| Most common failures | No# failures |
|---|
| Brake pipe excessively corroded | 40 |
| Brake hose excessively deteriorated | 40 |
| Headlamp aim out of alignment | 29 |
| Windscreen wiper does not clear the windscreen effectively | 22 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 20 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 17 |
| Nearside Stop lamp not working |1.2.1b| | 14 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 14 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 13 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 11 |
| Offside Stop lamp not working |1.2.1b| | 11 |
| Horn not working |1.6.2a| | 10 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 10 |
| Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 10 |
| Brakes imbalanced across an axle | 10 |
| Service brake: efficiency below requirements |3.7.B.7| | 9 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 9 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
| Rear parking brake recording little or no effort | 7 |
| Parking brake: efficiency below requirements |3.7.B.7| | 7 |
| Offside Rear fog lamp not working |1.3.2b| | 7 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 7 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 7 |
| Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 6 |
| Rear brake application uneven | 6 |
| Nearside Rear Stop lamp not working |1.2.1b| | 6 |
| Emissions not tested |7.0| | 5 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
| Driver`s seat insecure |6.2.A.1| | 5 |
| Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 5 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 5 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 4 |
| Nearside Side repeater not working |1.4.A.2c| | 4 |
| Rear Exhaust system not adequately supported |7.1.1| | 4 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
| Exhaust engine idle speed too high |7.3.D.1| | 4 |
| Offside Windscreen wiper blade deteriorated |8.2.2| | 4 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Registration plate issues | 4 |
| Fuel system component leaking |7.2.3| | 3 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 3 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 3 |
| Offside Rear Stop lamp not working |1.2.1b| | 3 |
| Brake hose damaged | 3 |
| Rear fog lamp tell tale not working |1.3.1b| | 3 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 3 |
| Nearside Rear Direction indicator not working |1.4.A.2c| | 2 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Fuel pipe leaking |7.2.3| | 2 |
| Brake pedal spongy |3.3.B.1b| | 2 |
| Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 2 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Front Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 2 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 2 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 2 |
| Nearside Front Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Front Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 2 |
| Nearside Rear Braking system leaking |3.6.A.1| | 2 |
| Offside Steering rack gaiter split |2.2.D.2d| | 2 |
| Centre Exhaust system not adequately supported |7.1.1| | 2 |
| Front Fuel hose leaking |7.2.3| | 2 |
| Offside Outer Front Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Nearside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 2 |
| Nearside Rear passenger seat cannot be secured in the upright position. |6.2.3| | 2 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 2 |
| Registration plate lamp issues | 2 |
| Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 2 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 2 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 2 |
| Rear Stop lamp not working |1.2.1b| | 2 |
| Offside Rear wheel cylinder leaking |3.6.A.1| | 2 |
| Brake pedal has insufficient reserve movement |3.3.A.5| | 2 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 2 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 2 |
| Mechanical brake component has restricted free movement | 2 |
| Rear Fuel pipe leaking |7.2.3| | 2 |
| Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Brake load sensing valve linkage seized |3.6.E.3| | 2 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Side repeater incomplete |1.5.A1b| | 2 |
| Nearside Front Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 2 |
| Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Front Brake hose twisted |found during steering lock to lock check| |2.2.D.2b| | 1 |
| Nearside front brake juddering severely |3.7.A.2b| | 1 |
| Rear Front passenger seat cannot be secured in the upright position. |6.2.4| | 1 |
| Brake pedal anti-slip provision incomplete |3.3.A.1b| | 1 |
| Nearside Front position lamp|s| not in good working order |function impaired| |1.1.4a| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Front passenger seat insecure |6.2.3| | 1 |
| An item not tested |Manual| | 1 |
| Nearside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Parking brake lever releases when knocked |3.1.6a| | 1 |
| Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Steering column shaft has excessive end float |2.1.3| | 1 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Inner Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Offside Rear Braking system leaking |3.6.A.1| | 1 |
| Offside Front Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| Outer Exhaust system not adequately supported |7.1.1| | 1 |
| Front Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Offside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Nearside Obligatory mirror insecure |8.1.1| | 1 |
| Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Offside Rear Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Side repeater incomplete |1.5.A1b| | 1 |
| Rear Fuel hose leaking |7.2.3| | 1 |
| Nearside Front Track rod end ball pin shank loose |2.2.B.1c| | 1 |
| Offside Front Side repeater not working |1.4.A.2c| | 1 |
| Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Horn not loud enough to be heard by another road user |1.6.2b| | 1 |
| Nearside Headlamps matched pair are not the same colour |1.7.6| | 1 |
| Centre Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Nearside Rear Sub-frame corroded and seriously weakened |2.4.G.1| | 1 |
| Rear Seat belt affected by an insecure seat fixing |5.2.1b| | 1 |
| Rear Emissions not tested |7.0| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Braking system leaking |3.6.A.1| | 1 |
| Offside Front Seat belt affected by an insecure seat fixing |5.2.1b| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 1 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Front Brake hose excessively damaged (1.1.12 (b) (ii)) | 1 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 1 |
| Service brake efficiency less than 50% of the required value this vehicle should not be driven until repairs have been carried out (1.2.2 (a) (ii)) | 1 |
| Offside Front Upper Macpherson strut top bush or bearing has excessive wear or free play (5.3.4 (a) (i)) | 1 |
| Exhaust catalytic converter missing where one was fitted as standard (8.2.1.1 (a)) | 1 |
| Brake performance not tested front road wheel brakes , foot to the floor (1.2.1 (g)) | 1 |
| Nearside Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Rear brake binding | 1 |
| Nearside Front Valve stem seriously damaged splitting at base of valve |4.1.D.1e| | 1 |
| Electrical wiring insecure at various points under bonnet |1.9.2a| | 1 |
| Nearside Rear Rear position lamp|s| has less than 50% of the light sources illuminating side light |1.1.A.3b| | 1 |
| Service brake efficiency below requirements |1.2.2 |a| |i|| | 1 |
| Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
| Rear Brake load sensing valve has been disconnected and was fitted as standard |3.6.E.2| | 1 |
| Nearside Rear Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Direction indicators not working |1.4.A.2c| | 1 |
| Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 1 |
| Nearside Front Steering rack gaiter split |2.2.D.2d| | 1 |
| Offside Service brake: efficiency below requirements |3.7.B.7| | 1 |
| Offside Parking brake: efficiency below requirements |3.7.B.7| | 1 |
| Nearside Front Body or chassis is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Body or chassis is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Coil spring modified so the suspension is inoperative (5.3.1 (d) (ii)) | 1 |
| Offside Front Coil spring modified so the suspension is inoperative (5.3.1 (d) (ii)) | 1 |
| Electrical wiring insulation in such a condition there is an imminent risk of fire or formation of sparks Wiring touching steering rack and sparking (4.11 (c) (iii)) | 1 |
| Nearside Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Offside Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Nearside Rear Service brake lagging in operation (1.2.1 (d)) | 1 |
| Nearside Front Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Offside Front Shock absorbers has negligible damping effect (5.3.2 (d)) | 1 |
| Nearside Rear Lower Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear passenger seat cannot be secured in the upright position. |6.2.3| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Front Road wheel bead rim badly distorted |4.2.A.1a| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Front Side repeater excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Nearside Front Side repeater not working |1.4.A.2c| | 1 |
| Nearside Rear Direction indicators not working |1.4.A.2c| | 1 |
| Offside Rear Fuel hose leaking |7.2.3| | 1 |
| Offside Lower Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Front position lamp|s| not in good working order |function impaired| |1.1.4a| | 1 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 1 |
| Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 1 |
| Centre Front Upper Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Inner Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Centre Front Fuel hose leaking |7.2.3| | 1 |
| Centre Rear Fuel hose leaking |7.2.3| | 1 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Rear fog lamp switch inoperative (4.5.3 (a)) | 1 |
| Fuel cap/sealing device sealing washer torn |7.2.4c| | 1 |
| Nearside rear brakes release unevenly |3.7.B.4| | 1 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Nearside Windscreen washer jets misaligned and not providing sufficient fluid to the windscreen (3.5 (a)) | 1 |
| Offside Rear Wheel bearing rough when rotated |5.1.3 |b| |i|| | 1 |
| Exhaust system insecure centre & rear Pipes |6.1.2 |a|| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Rear fog lamp switch faulty |1.3.1a| | 1 |
| Nearside Front Front drive shaft coupling is insecure |2.5.C.1c| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Centre Rear Statutory seat belt missing |5.1.1| | 1 |
| Offside Rear Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Driver`s door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Nearside Front Side repeater missing |1.4.A.2b| | 1 |
| Main beam `tell-tale` not working |1.7.4c| | 1 |
| Offside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
| Nearside Rear Exhaust mounting missing |7.1.1b| | 1 |
| Nearside Front front brake binding |3.7.B.1| | 1 |
| Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Outer Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Front brake disc excessively scored |3.5.1h| | 1 |
| Nearside rear brake grabbing severely |3.7.A.5b| | 1 |
| Brake pipe leaking |3.6.A.1| | 1 |
| Obligatory mirror missing |8.1.1| | 1 |
| Centre Exhaust mounting missing |7.1.1b| | 1 |
| Nearside Valve stem seriously misaligned |4.1.D.1e| | 1 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Direction indicators not working |1.4.A.2c| | 1 |
| Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Fuel hose leaking |7.2.3| | 1 |
| Offside Rear Fuel pipe leaking |7.2.3| | 1 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear position lamp|s| insecure |1.1.A.3a| | 1 |
| Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Rear Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Steering rack gaiter split |2.2.D.2d| | 1 |
| Nearside Rear Lower Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Offside Rear Lower Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Side repeater not working |1.4.A.2c| | 1 |
| Nearside Rear Shock absorbers has a serious fluid leak | 1 |
| Offside Front Side repeater insecure |1.4.A.2b| | 1 |
| Centre Front Steering rack gaiter split |2.2.D.2d| | 1 |
| Nearside Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Offside Side repeater incorrect colour |1.4.A.2f| | 1 |
| Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded Quarter panel area |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Under arch |2.4.A.3| | 1 |