| Most common failures | No# failures |
|---|
| Brake pipe excessively corroded | 21 |
| Brake hose excessively deteriorated | 17 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 9 |
| Windscreen wiper does not clear the windscreen effectively | 8 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 7 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
| Headlamp aim out of alignment | 7 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 6 |
| Rear brake application uneven | 5 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 5 |
| Rear parking brake recording little or no effort | 5 |
| Service brake: efficiency below requirements |3.7.B.7| | 5 |
| Parking brake: efficiency below requirements |3.7.B.7| | 5 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 5 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 5 |
| Brake hose damaged | 4 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 4 |
| Windscreen has damage | 4 |
| Exhaust system not adequately supported |7.1.1| | 4 |
| Nearside Stop lamp not working |1.2.1b| | 4 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 4 |
| Registration plate lamp issues | 4 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 4 |
| Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 4 |
| Brakes imbalanced across an axle | 4 |
| Rear Exhaust system not adequately supported |7.1.1| | 3 |
| Horn not working |1.6.2a| | 3 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 3 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 2 |
| Nearside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Rear Exhaust mounting missing |7.1.1b| | 2 |
| Centre Exhaust mounting missing |7.1.1b| | 2 |
| Rear Fuel pipe leaking |7.2.3| | 2 |
| Centre Exhaust system not adequately supported |7.1.1| | 2 |
| Offside Rear fog lamp not working |1.3.2b| | 2 |
| Offside Side repeater incorrect colour |1.4.A.2f| | 2 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 2 |
| Rear Fuel hose leaking |7.2.3| | 2 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 2 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 2 |
| Rear Rear fog lamp not working |1.3.2b| | 2 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 2 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 2 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Offside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Rear Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
| Nearside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Obligatory mirror insecure |8.1.1| | 1 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 1 |
| Offside Front Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| Front Fuel hose leaking |7.2.3| | 1 |
| Nearside Front Brake hose twisted |found during steering lock to lock check| |2.2.D.2b| | 1 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Outer Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Hazard warning switch faulty |1.4.B.1d| | 1 |
| Offside Front Side repeater excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Offside Rear Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| Nearside Front Steering rack gaiter split |2.2.D.2d| | 1 |
| Offside Front Steering rack gaiter split |2.2.D.2d| | 1 |
| Rear Brake valve leaking |3.6.A.1| | 1 |
| Nearside Rear Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| Exhaust mounting missing |7.1.1b| | 1 |
| Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Offside Front Seat belt damaged sufficient to obstruct correct operation of the belt |5.2.2a| | 1 |
| Nearside Obligatory mirror insecure |8.1.1| | 1 |
| Nearside Rear Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Side repeater not working |1.4.A.2c| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Rear Service brake imbalanced across an axle (1.2.1 (b) (i)) | 1 |
| Emissions unable to be completed (8.2.1.2 (d)) | 1 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |
| Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced floor (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Brake load sensing valve seized and ABS not fitted or inoperative (1.1.17 (c) (ii)) | 1 |
| Offside Outer Front Side repeater not working |1.4.A.2c| | 1 |
| Nearside Outer Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Outer Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Front Side repeater not working |1.4.A.2c| | 1 |
| Nearside Rear Stop lamp not working |1.2.1b| | 1 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Front Seat belt insecurely fixed to the seat |5.2.1a| | 1 |
| Offside Front Seat belt insecurely fixed to the seat |5.2.1a| | 1 |
| Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Front brake application uneven | 1 |
| Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Emissions not tested |7.0| | 1 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Fuel system component leaking |7.2.3| | 1 |
| Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
| Offside Rear passenger seat cannot be secured in the upright position. |6.2.3| | 1 |
| Offside Rear Stop lamp not working |1.2.1b| | 1 |
| Registration plate issues | 1 |
| Nearside Front Obligatory mirror missing |8.1.1| | 1 |
| Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Centre Front Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Rear Lower Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Rear Rear passenger seat cannot be secured in the upright position. |6.2.3| | 1 |
| Offside Stop lamp not working |1.2.1b| | 1 |
| Tailgate cannot be secured in the closed position |6.4.1| | 1 |
| Offside Rear Brake hose bulging under pressure |3.6.B.3| | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Centre Fuel hose leaking |7.2.3| | 1 |
| Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 1 |
| Offside Obligatory mirror missing |8.1.1| | 1 |
| Offside Front Driver`s seat insecure |6.2.A.1| | 1 |
| Offside Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Rear Parking brake is not capable of being maintained in operation by direct mechanical action only |3.1.2| | 1 |
| Offside Rear Macpherson strut corroded and seriously weakened |2.4.G.1| | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Offside Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Offside Rear fog lamp adversely affected by the operation of another lamp |1.3.2f| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Rear Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Fuel pipe leaking |7.2.3| | 1 |
| Exhaust engine idle speed too high |7.3.D.1| | 1 |
| Brake pedal creeps down while the pedal is held under pressure |3.3.B.1a| | 1 |
| Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Rear Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 1 |
| Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Centre Front Brake pedal spongy |3.3.B.1b| | 1 |
| Offside Front Headlamps matched pair are incorrectly positioned |1.7.3| | 1 |
| Offside Rear Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 1 |
| Centre Front Horn not working |1.6.2a| | 1 |
| Nearside Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |