Most common failures | No# failures |
---|
Registration plate issues | 47 |
Rear reflector on motorcycle missing |1.4.1| | 26 |
Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 10 |
Horn missing |1.7.1| | 9 |
Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 9 |
Rear reflector missing (4.8.2 (a) (ii)) | 9 |
Headlamp aim out of alignment | 8 |
Horn not working |1.7.3a| | 7 |
Headlamp at least one does not illuminate on main beam |1.2.2a|ii|| | 6 |
Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 5 |
Horn not working |7.7 |a| |ii|| | 4 |
Rear Rear reflector missing (4.8.2 (a) (ii)) | 4 |
Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 4 |
Headlamp not working on main beam (4.1.1 (a) (ii)) | 4 |
Front Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 3 |
Offside Front shock absorber seal failed and leaking oil |2.3.3| | 3 |
Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 3 |
Front Stop lamp remains on when the brake is released |1.3.1e| | 3 |
Nearside Front shock absorber seal failed and leaking oil |2.3.3| | 3 |
Front position lamp does not illuminate immediately when switched on |1.1.3a| | 2 |
Rear wheel bearings have excessive free play |2.4.A.2c| | 2 |
Front shock absorber seal failed and leaking oil |2.3.3| | 2 |
Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 2 |
Rear Rear reflector on motorcycle missing |1.4.1| | 2 |
Headlamp aim not tested |1.6| | 2 |
Rear reflector missing |4.8.2 |a| |ii|| | 2 |
Stop lamp remains on when the brakes are released | 2 |
Rear Wheel spoke excessively loose (5.2.2 (d)) | 2 |
Rear Stop lamp not working (4.3.1 (a) (ii)) | 2 |
Horn not working (7.7 (a)) | 2 |
Front Brake disc|s| excessively worn |3.2.A1l| | 1 |
Front Floor brake test indicates a binding brake |3.3.C2c| | 1 |
Vehicle identification number not legible |6.3.5a| | 1 |
Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 1 |
Drive chain sprocket worn to excess |6.2.1e| | 1 |
Rear Hydraulic brake control feels spongy |3.1.4a| | 1 |
Fairings so located that it is likely to impede the steering Front mudguard fouling frame. |2.1.2e| | 1 |
Headlamp aim not tested Lights not working. |1.6| | 1 |
Floor brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.C1b| | 1 |
Stop lamp remains on when the brake is released |1.3.1e| | 1 |
Front wheel bearings are excessively rough |2.3.5b| | 1 |
Front wheel bearings are excessively tight |2.3.5b| | 1 |
Offside Front Shock absorber has a serious fluid leak |5.3.2 |b|| | 1 |
Rear Rear reflector missing |4.8.2 |a| |ii|| | 1 |
Front Handlebar mounting clamp loose |2.1.1a| | 1 |
Front Handlebar mounting clamp bolt loose |2.1.1a| | 1 |
Rear Drive chain excessively loose |6.2.1d| | 1 |
Offside Rear reflector on motorcycle missing |1.4.1| | 1 |
Front Front wheel bearings have excessive free play |2.3.5b| | 1 |
Rear wheel spindle securing nut|s| loose |2.4.A.2b| | 1 |
Brake lever has inadequate reserve travel Front brake |3.1.3b| | 1 |
Drive chain excessively tight |6.2.1d| | 1 |
Central Rear Rear reflector on motorcycle does not reflect squarely to the rear |1.4.1| | 1 |
Rear Brake disc|s| excessively worn |3.2.A1l| | 1 |
Rear reflector on motorcycle incorrectly positioned |1.4.2d| | 1 |
Rear Rear wheel bearings have excessive free play |2.4.A.2c| | 1 |
Front Drive chain sprocket worn to excess |6.2.1e| | 1 |
Drive chain excessively loose |6.2.1d| | 1 |
Rear Stop lamp remains on when the brake is released |1.3.1e| | 1 |
Brake lever has inadequate reserve travel |3.1.3b| | 1 |
Locking device|s| not correctly fitted which may make the motor bicycle dangerous to ride |6.2.1h| | 1 |
Throttle operating incorrectly |6.2.1f| | 1 |
Front Brake locking device missing Pad Pin Clip Missing |3.2.A1e| | 1 |
Front Horn missing |1.7.1| | 1 |
Stop lamp does not illuminate immediately a brake applies Front And Rear |1.3.1a| | 1 |
Drive chain fouling another component |6.2.1d| | 1 |
Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Front Hydraulic brake control feels spongy |3.1.4a| | 1 |
Centre Rear Rear reflector on motorcycle missing |1.4.1| | 1 |
Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
Front wheel bearings have excessive free play |2.3.5b| | 1 |
Rear Wheel bearing play so excessive it is likely to break up (5.1.3 (a) (ii)) | 1 |
Horn not working (7.7 (a) (ii)) | 1 |
Wheel spoke excessively loose |4.2.1b| | 1 |
Stop lamp not working (4.3.1 (a) (ii)) | 1 |
Front Position lamp not working (4.2.1 (a)) | 1 |
Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
Throttle operating incorrectly dosnt return fully when on left hand full lock, cable too tight |6.2.1f| | 1 |
Nearside Front Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Rear Wheel bearing so rough it is likely to overheat or break up (5.1.3 (b) (ii)) | 1 |
Offside Front Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
All direction indicators missing |4.4.1 |a| |ii|| | 1 |
Drive chain excessively loose (6.1.7 (c) (i)) | 1 |
All position lamps not working |4.2.1 |a|| | 1 |
Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
Offside Front Upper Stop lamp switch with a delay in operation (4.3.2 (a) (ii)) | 1 |
Clutch lever shortened so it cannot be readily operated (6.2.7 (b)) | 1 |
Headlamp aim projected beam image obviously incorrect (4.1.2 (c)) | 1 |
Rear Position lamp not working (4.2.1 (a)) | 1 |
Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
Front Wheel bearing so rough it is likely to overheat or break up (5.1.3 (b) (ii)) | 1 |
Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
All position lamps not working (4.2.1 (a)) | 1 |
Stop lamp not working |4.3.1 |a| |ii|| | 1 |
Front Brake disc|s| is excessively distorted |3.2.A1m| | 1 |
Front Wheel bearing play so excessive it is likely to break up (5.1.3 (a) (ii)) | 1 |
Wheel alignment incorrect which adversely affects the steering (2.4 (a)) | 1 |
Stop lamp does not illuminate by the operation of both brake controls (4.3.2 (a) (iii)) | 1 |
Dipswitch does not operate immediately when selected on dipped beam (4.1.3 (b)) | 1 |