MOT History from tests of petrol KAWASAKI ZZRs year 2002

Review the list of common KAWASAKI ZZR failures below or to perform a specific mot history check on your KAWASAKI then use our popular KnowYourCar service

mot history

Pass percent:80.88%

(The average a petrol KAWASAKI ZZR year 2002 passes without issue)

Based on:136 MOT Tests

Most common failures	No# failures
Headlamp aim beam image kick up to the offside \|1.6\|	5
Registration plate lamp issues	3
Headlamp aim beam image kick-up is to the offside \|1.6.1\|	2
Headlamp aim out of alignment	2
Front Stop lamp does not illuminate immediately a brake applies \|1.3.1a\|	2
Front Roller brake test indicates a binding brake \|3.3.A1a\|	1
Rear Stop lamp does not illuminate immediately a brake applies \|1.3.1a\|	1
Rear Drive chain excessively tight \|6.2.1d\|	1
Rear wheel bearings have excessive free play \|2.4.A.2c\|	1
Front Roller brake test indicates excessive fluctuation of brake effort \|3.3.A1d\|	1
Front wheel spindle securing nut\|s\| loose \|2.3.5a\|	1
Front wheel spindle securing nut locking device insecure \|2.3.5a\|	1
Front position lamp does not illuminate immediately when switched on \|1.1.3a\|	1
Headlamp at least one does not illuminate on dipped beam \|1.2.2a\|i\|\|	1
Headlamp at least one does not illuminate on main beam \|1.2.2a\|ii\|\|	1
Front Headlamp aim beam image kick up to the offside \|1.6\|	1
Rear wheel spindle securing nut locking device missing \|2.4.A.2b\|	1
Nearside Rear position lamp does not illuminate immediately when it is switched on \|1.1.3a\|	1
Offside Rear position lamp does not illuminate immediately when it is switched on \|1.1.3a\|	1
Centre Rear Rear reflector on motorcycle missing \|1.4.1\|	1
Nearside Drive chain excessively loose \|6.2.1d\|	1
Nearside Drive chain worn to excess \|6.2.1e\|	1
Front Drive chain sprocket worn to excess \|6.2.1e\|	1
Front Floor brake test indicates a binding brake \|3.3.C2c\|	1
Front suspension has excessive stiffness in the suspension movement. \|2.3.6b\|	1
Drive chain worn to excess \|6.2.1e\|	1
Front suspension assembly component excessively corroded. \|2.3.1\|	1
Headlamp aim beam image too far to the right \|1.6.4\|	1
Front position lamp insecure \|1.1.1c\|	1
Front Wheel damaged significantly reducing the original strength \|4.2.1a\|	1
Front Front shock absorber seal failed and leaking oil \|2.3.3\|	1
Exhaust has a major leak of exhaust gases (6.1.2 (a))	1
Front Stop lamp does not illuminate by the operation of both brake controls (4.3.2 (a) (iii))	1

We get to these numbers by trawling through over 1 billion MOT test results since 2004 and crunched the numbers. We remove anything to do with Tyres, as they are model independent and group together common non-model specific issues. We are trying to get to a picture of what models have what issues.

Please note: We take the data from the DVSA. This data is raw and can contain typos and spelling mistakes that garages may have entered while recording a MOT result. Specifically miss-match on names of models and makes. We are constantly cleaning the data so bear with the odd issue.

Got suggestions? We’re improving this section all the time. If you have any suggestions, please let us know.

Most common failures	No# failures
Headlamp aim beam image kick up to the offside \|1.6\|	5
Registration plate lamp issues	3
Headlamp aim beam image kick-up is to the offside \|1.6.1\|	2
Headlamp aim out of alignment	2
Front Stop lamp does not illuminate immediately a brake applies \|1.3.1a\|	2
Front Roller brake test indicates a binding brake \|3.3.A1a\|	1
Rear Stop lamp does not illuminate immediately a brake applies \|1.3.1a\|	1
Rear Drive chain excessively tight \|6.2.1d\|	1
Rear wheel bearings have excessive free play \|2.4.A.2c\|	1
Front Roller brake test indicates excessive fluctuation of brake effort \|3.3.A1d\|	1
Front wheel spindle securing nut\|s\| loose \|2.3.5a\|	1
Front wheel spindle securing nut locking device insecure \|2.3.5a\|	1
Front position lamp does not illuminate immediately when switched on \|1.1.3a\|	1
Headlamp at least one does not illuminate on dipped beam \|1.2.2a\|i\|\|	1
Headlamp at least one does not illuminate on main beam \|1.2.2a\|ii\|\|	1
Front Headlamp aim beam image kick up to the offside \|1.6\|	1
Rear wheel spindle securing nut locking device missing \|2.4.A.2b\|	1
Nearside Rear position lamp does not illuminate immediately when it is switched on \|1.1.3a\|	1
Offside Rear position lamp does not illuminate immediately when it is switched on \|1.1.3a\|	1
Centre Rear Rear reflector on motorcycle missing \|1.4.1\|	1
Nearside Drive chain excessively loose \|6.2.1d\|	1
Nearside Drive chain worn to excess \|6.2.1e\|	1
Front Drive chain sprocket worn to excess \|6.2.1e\|	1
Front Floor brake test indicates a binding brake \|3.3.C2c\|	1
Front suspension has excessive stiffness in the suspension movement. \|2.3.6b\|	1
Drive chain worn to excess \|6.2.1e\|	1
Front suspension assembly component excessively corroded. \|2.3.1\|	1
Headlamp aim beam image too far to the right \|1.6.4\|	1
Front position lamp insecure \|1.1.1c\|	1
Front Wheel damaged significantly reducing the original strength \|4.2.1a\|	1
Front Front shock absorber seal failed and leaking oil \|2.3.3\|	1
Exhaust has a major leak of exhaust gases (6.1.2 (a))	1
Front Stop lamp does not illuminate by the operation of both brake controls (4.3.2 (a) (iii))	1

MOT History from tests of petrol KAWASAKI ZZRs year 2002

Find us on Facebook