Most common failures | No# failures |
---|
Headlamp aim out of alignment | 20 |
Rear reflector on motorcycle missing |1.4.1| | 15 |
Registration plate issues | 8 |
Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 8 |
Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 7 |
Horn not working |1.7.3a| | 6 |
Front Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 6 |
Steering headbearing has excessive free play |2.2.2| | 5 |
Wheel alignment incorrect which adversely affects the handling |2.5.1| | 5 |
Drive chain worn to excess |6.2.1e| | 4 |
Rear Rear reflector on motorcycle missing |1.4.1| | 4 |
Rear suspension movement is excessively stiff |2.4.A.3b| | 3 |
Locking devices not correctly fitted which may make the motor bicycle dangerous to ride |6.2.1h| | 3 |
Drive chain excessively loose |6.2.1d| | 3 |
Rear Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 3 |
Direction indicators not working |1.5.1c| | 3 |
Front Brake lever has inadequate reserve travel |3.1.3b| | 3 |
Horn not loud enough to be heard by another road user |1.7.3a| | 3 |
Rear reflector missing (4.8.2 (a) (ii)) | 3 |
Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 3 |
Front Brake disc|s| excessively worn |3.2.A1l| | 3 |
Rear Brake disc|s| excessively worn |3.2.A1l| | 3 |
Rear Roller brake test indicates a binding brake |3.3.A1a| | 3 |
Rear wheel spindle securing nut locking device missing |2.4.A.2b| | 2 |
Exhaust is leaking and excessively noisey |7.1.1b| | 2 |
Drive chain excessively tight |6.2.1d| | 2 |
Rear Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 2 |
Fuel system component insecure |7.2.1b| | 2 |
Rear Wheel spoke excessively loose |4.2.1b| | 2 |
Front Direction indicator not working |1.5.1c| | 2 |
Front Roller brake test indicates a binding brake |3.3.A1a| | 2 |
Nearside Rear Direction indicators not working |1.5.1c| | 2 |
Rear suspension bearing has excessive free play |2.4.A2a|i|| | 2 |
Offside Rear Direction indicator not working |1.5.1c| | 2 |
Nearside Front shock absorber seal failed and leaking oil |2.3.3| | 2 |
Nearside Rear Footrest missing |6.2.1a| | 2 |
Offside Rear Footrest missing |6.2.1a| | 2 |
Locking device|s| not correctly fitted which may make the motor bicycle dangerous to ride |6.2.1h| | 2 |
Front position lamp does not illuminate immediately when switched on |1.1.3a| | 2 |
Brake hose damaged | 2 |
Front wheel bearings have excessive free play |2.3.5b| | 2 |
Brake hose excessively deteriorated | 2 |
Rear Rear mono-shock pivot excessively worn |2.4.B.4| | 2 |
Roller brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.A2b| | 2 |
Nearside Handlebar handgrip not secure to handlebars. |2.1.1c| | 2 |
Front Position lamp not working side light in-op (4.2.1 (a)) | 2 |
Fuel system component leaking |7.2.1a| | 1 |
Direction indicator not working |1.5.1c| | 1 |
Front Floor brake test indicates a binding brake |3.3.C2c| | 1 |
Rear Footrest missing |6.2.1a| | 1 |
Rear Direction indicator missing |1.5.1a| | 1 |
Rear position lamp damaged and function impaired |1.1.1b| | 1 |
All position lamps do not illuminate immediately when switched on |1.1.3a| | 1 |
Rear All position lamps do not illuminate immediately when switched on |1.1.3a| | 1 |
Nearside Front Front wheel spindle securing nut locking device missing |2.3.3a| | 1 |
Nearside Rear Front wheel spindle securing nut locking device missing |2.3.3a| | 1 |
Rear Wheel more than one fixing loose |5.2.1 |a| |ii|| | 1 |
Front Wheel bearing has excessive play |5.1.3 |a| |i|| | 1 |
Rear reflector missing |4.8.2 |a| |ii|| | 1 |
Front Brake disc|s| has excessive run out |3.2.A1m| | 1 |
Front Roller brake test indicates excessive fluctuation of brake effort |3.3.A1d| | 1 |
Offside Front Direction indicator not working |1.5.1c| | 1 |
Front Direction indicator affected by the operation of another lamp |1.5.1c| | 1 |
Rear Direction indicator affected by the operation of another lamp |1.5.1c| | 1 |
Front Direction indicator deteriorated and function impaired |1.5.3a| | 1 |
Rear Direction indicator deteriorated and function impaired |1.5.3a| | 1 |
Central Rear Wheel fixing missing |single fixing| |5.2.1 |a| |ii|| | 1 |
Brake component modification unsafe brake disc fouling calliper (1.1.21 (d) (i)) | 1 |
Rear Lower Suspension component pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Front Direction indicator not working |1.5.1c| | 1 |
Offside Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Front Wheel spoke excessively loose |4.2.1b| | 1 |
Nearside Steering lock stop ineffective |2.1.3| | 1 |
Nearside Rear Direction indicator not working |1.5.1c| | 1 |
Front Brake master cylinder fluid level dangerously low |3.2.B1d| | 1 |
Plate brake test No brake control achieves an efficiency of 30%. |3.3.B2a| | 1 |
Indicator tell tale not operating correctly |1.5.2| | 1 |
Steering movement excessively stiff with the weight on the lower bearing |2.2.1a| | 1 |
Roller brake test No brake control achieves an efficiency of 30%. |3.3.A2a| | 1 |
Steering control fouling between components which interferes with the free movement of the steering |2.1.2a| | 1 |
Indicator switch does not operate the direction indicators on the side selected |1.5.4| | 1 |
Front Brake pipe excessively chafed |3.2.B2a| | 1 |
Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 1 |
Nearside Front Direction indicators not working |1.5.1c| | 1 |
Rear wheel bearings have excessive free play |2.4.A.2c| | 1 |
Rear suspension bush has excessive free play |2.4.A2a|i|| | 1 |
Offside Rear wheel spindle securing nut locking device insecure |2.4.A.2b| | 1 |
Front Brake hose fouling |3.2.B3b| | 1 |
Front Front wheel bearings are excessively rough |2.3.5b| | 1 |
Rear Rear position lamp insecure |1.1.1c| | 1 |
Rear Exhaust mounting does not fully support the exhaust system |7.1.1.c| | 1 |
Rear Rear wheel spindle securing nut locking device missing |2.4.A.2b| | 1 |
Front Headlamp aim beam image too far to the right |1.6.4| | 1 |
Front Direction indicator insecure |1.5.3b| | 1 |
Lower Rear mono-shock pivot excessively worn |2.4.B.4| | 1 |
Rear position lamp incorrect colour |1.1.2b| | 1 |
Wheel corroded significantly reducing the original strength |4.2.1a| | 1 |
Rear Lower Rear mono-shock pivot excessively worn |2.4.B.4| | 1 |
Rear wheel spindle loose |2.4.A.2b| | 1 |
Rear Brake cylinder insecurely mounted |3.2.B1a| | 1 |
Rear Drive chain excessively loose |6.2.1d| | 1 |
Nearside Rear Footrest insecure |6.2.1a| | 1 |
Offside Rear Footrest insecure |6.2.1a| | 1 |
Offside Front Handlebar handgrip not secure to handlebars. |2.1.1c| | 1 |
Rear Lower Rear suspension bush has excessive free play |2.4.A2a|i|| | 1 |
Rear Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 1 |
Rear Brake pedal has inadequate reserve travel |3.1.3b| | 1 |
Rear Brake pedal cannot be applied smoothly |3.1.3d| | 1 |
Front Throttle has a significant change in engine speed whilst moving the steering from lock to lock |2.1.4| | 1 |
Handlebar deformed |2.1.1b| | 1 |
Nearside Rear Drive chain horseshoe locking device incorrectly fitted |6.1.7 |j| |i|| | 1 |
Front Handlebar handgrip not secure to handlebars. |2.1.1c| | 1 |
Exhaust noise is clearly in excess of that emitted by a similar motor bicycle fitted with a standard silencer in average condition |7.1.2| | 1 |
Rear position lamp deteriorated and function impaired |1.1.1b| | 1 |
Rear Locking devices not correctly fitted which may make the motor bicycle dangerous to ride |6.2.1h| | 1 |
Front Hydraulic brake control feels spongy |3.1.4a| | 1 |
Lower Rear suspension bush has excessive free play |2.4.A2a|i|| | 1 |
Rear Stop lamp remains on when the brake is released |1.3.1e| | 1 |
Horn is not a constant note |1.7.3c| | 1 |
Front Direction indicators affected by the operation of another lamp |1.5.1c| | 1 |
Rear Direction indicators flashing less than 60 times a minute |1.5.1c| | 1 |
Offside Rear Direction indicators not working |1.5.1c| | 1 |
Front Wheel corroded significantly reducing the original strength |4.2.1a| | 1 |
Rear Suspension arm pin or bush excessively worn linkage bearings/bushes (5.3.4 (a) (i)) | 1 |
Rear Drive chain sprocket worn to excess (6.1.7 (c) (i)) | 1 |
Drive chain worn to excess (6.1.7 (c) (i)) | 1 |
Front wheel spindle securing nut locking device missing |2.3.3a| | 1 |
Rear Front wheel spindle securing nut locking device missing |2.3.3a| | 1 |
Headlamp at least one does not illuminate on main beam |1.2.2a|ii|| | 1 |
Rear Roller brake test indicates excessive fluctuation of brake effort |3.3.A1d| | 1 |
Horn sound not in accordance with requirements not loud enough (7.7 (c)) | 1 |
Wheel spindle locking device missing split pin missing (5.2.1 (d)) | 1 |
Rear Wheel spindle or securing nut(s) so insecure that wheel security or steering control is adversely affected wheel insecure (5.2.1 (c) (ii)) | 1 |
Brake lever has inadequate reserve travel |3.1.3b| | 1 |
Front position lamp obscured more than 50% |1.1.1d| | 1 |
Direction indicators affected by the operation of another lamp |1.5.1c| | 1 |
Front Exhaust mounting does not fully support the exhaust system |7.1.1.c| | 1 |
Exhaust excessively deteriorated |7.1.1a| | 1 |
Rear Exhaust is leaking and excessively noisey |7.1.1b| | 1 |
Rear Rear wheel bearings have excessive free play |2.4.A.2c| | 1 |
Rear Direction indicator not working |1.5.1c| | 1 |