Most common failures | No# failures |
---|
Headlamp aim out of alignment | 32 |
Rear reflector on motorcycle missing |1.4.1| | 27 |
Front Roller brake test indicates a binding brake |3.3.A1a| | 14 |
Registration plate issues | 12 |
Rear Roller brake test indicates a binding brake |3.3.A1a| | 12 |
Horn not working |1.7.3a| | 11 |
Nearside Front shock absorber seal failed and leaking oil |2.3.3| | 10 |
Front Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 8 |
Offside Front shock absorber seal failed and leaking oil |2.3.3| | 7 |
Rear Rear reflector on motorcycle missing |1.4.1| | 6 |
Front Roller brake test indicates excessive fluctuation of brake effort |3.3.A1d| | 6 |
Front Front shock absorber seal failed and leaking oil |2.3.3| | 5 |
Headlamp aim beam image kick up to the offside |1.6| | 5 |
Offside Front Brake disc|s| friction surface contaminated by oil or grease |3.2.A1k| | 4 |
Drive chain excessively loose |6.2.1d| | 4 |
Rear Roller brake test indicates excessive fluctuation of brake effort |3.3.A1d| | 4 |
Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 4 |
Roller brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.A2b| | 4 |
Rear wheel bearings have excessive free play |2.4.A.2c| | 4 |
Front position lamp does not illuminate immediately when switched on |1.1.3a| | 4 |
Steering headbearing has excessive free play |2.2.2| | 4 |
Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 4 |
Horn not working |7.7 |a| |ii|| | 4 |
Rear Stop lamp remains on when the brake is released |1.3.1e| | 3 |
Rear Rear wheel bearings have excessive free play |2.4.A.2c| | 3 |
Rear Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 3 |
Drive chain excessively tight |6.2.1d| | 3 |
Throttle operating incorrectly |6.2.1f| | 3 |
Front wheel bearings are excessively rough |2.3.5b| | 3 |
Drive chain fouling another component |6.2.1d| | 3 |
Riders seat insecure |6.2.1a| | 3 |
Rear wheel spindle loose |2.4.A.2b| | 3 |
Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 3 |
Front shock absorber seal failed and leaking oil |2.3.3| | 3 |
Front Horn not working |1.7.3a| | 3 |
Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 3 |
Registration plate lamp issues | 3 |
Offside Front Shock absorber has a serious fluid leak (5.3.2 (b)) | 3 |
Front Position lamp not working |4.2.1 |a|| | 2 |
Exhaust noise is clearly in excess of that emitted by a similar motor bicycle fitted with a standard silencer in average condition |7.1.2| | 2 |
Nearside Handlebar handgrip not secure to handlebars. |2.1.1c| | 2 |
Horn not loud enough to be heard by another road user |1.7.3a| | 2 |
Rear Wheel alignment incorrect which adversely affects the handling |2.5.1| | 2 |
Throttle has a significant change in engine speed whilst moving the steering from lock to lock |2.1.4| | 2 |
Front suspension has excessive stiffness in the suspension movement. |2.3.6b| | 2 |
Wheel alignment incorrect which adversely affects the handling |2.5.1| | 2 |
Brake pedal has inadequate reserve travel |3.1.3b| | 2 |
Drive chain worn to excess |6.2.1e| | 2 |
Handlebar mounting clamp bolt loose |2.1.1a| | 2 |
Rear Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 2 |
Front Stop lamp remains on when the brake is released |1.3.1e| | 2 |
Front Brake lever has inadequate reserve travel |3.1.3b| | 2 |
Exhaust mounting does not fully support the exhaust system |7.1.1.c| | 2 |
Rear Roller brake test indicates a sticking brake |3.3.A1a| | 2 |
Rear Brake pedal has inadequate reserve travel |3.1.3b| | 2 |
Rear Rear suspension bush has excessive free play |2.4.A2a|i|| | 2 |
Wheel alignment incorrect which adversely affects the steering |2.5.1| | 2 |
Horn control defective |1.7.2a| | 2 |
Brake hose excessively deteriorated | 2 |
Front Floor brake test indicates a binding brake |3.3.C2c| | 2 |
Front Direction indicators not working |1.5.1c| | 2 |
Front Brake disc|s| friction surface contaminated by oil or grease |3.2.A1k| | 2 |
Rear Position lamp not working (4.2.1 (a)) | 2 |
Throttle operating incorrectly (6.2.7 (a) (i)) | 2 |
Roller brake test The less effective brake control does not achieve an efficiency of 25% (1.2.2 (a) (i)) | 2 |
Rear reflector missing (4.8.2 (a) (ii)) | 2 |
Drive chain excessively loose |6.1.7 |c| |i|| | 1 |
Offside Front Direction indicator not working |1.5.1c| | 1 |
Front Brake disc|s| is excessively distorted |3.2.A1m| | 1 |
Offside Rear Brake disc|s| excessively worn |3.2.A1l| | 1 |
Offside Rear Brake pipe likely to be fouled or trapped by moving parts |3.2.B2c| | 1 |
Offside Rear Brake pipe inadequately supported |3.2.B2b| | 1 |
Rear Brake reaction bracket securing bolt|s| loose |3.2.A1j| | 1 |
Rear Drive chain excessively loose |6.2.1d| | 1 |
Rear Drive chain worn to excess |6.2.1e| | 1 |
Rear Drive chain sprocket carrier worn to excess |6.2.1e| | 1 |
Rear Drive chain sprocket worn to excess |6.2.1e| | 1 |
Rear Brake reaction bracket insecure |3.2.A1j| | 1 |
Front Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 1 |
Position lamp switch insecure |1.1.4b| | 1 |
Rear Brake excessively binding |1.2.1 |f|| | 1 |
Rear Stop lamp not working |4.3.1 |a| |ii|| | 1 |
Floor brake test The less effective brake control does not achieve an efficiency of 25% |1.2.2 |a| |i|| | 1 |
Front Lower Rear suspension bearing has excessive free play |2.4.A2a|i|| | 1 |
Rear Brake hose is likely to be fouled or trapped by moving parts |3.2.B2c| | 1 |
Rear suspension bush has excessive free play |2.4.A2a|i|| | 1 |
Rear Roller brake test indicates brake effort rise disproportional to brake lever or pedal effort |3.3.A1c| | 1 |
Front Roller brake test indicates a severely grabbing brake |3.3.A1b| | 1 |
Front Plate brake test indicates a binding brake |3.3.B1a| | 1 |
Offside Front Upper Roller brake test indicates brake effort rise disproportional to brake lever or pedal effort |3.3.A1c| | 1 |
Headlamp at least one does not illuminate on main beam |1.2.2a|ii|| | 1 |
Nearside Front Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Rear Brake disc|s| cracked |3.2.A1g| | 1 |
Upper Rear suspension bush has excessive free play |2.4.A2a|i|| | 1 |
Offside Front Lower Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Brake hose damaged | 1 |
Steering movement excessively `notchy` with the wheel raised |2.2.1b| | 1 |
Rear suspension bearing has excessive free play |2.4.A2a|i|| | 1 |
Rear mono-shock pivot excessively worn |2.4.B.4| | 1 |
Offside Front Brake pipe union leaking fluid |3.2.B4| | 1 |
Fuel tank leaking |7.2.1a| | 1 |
Nearside Handlebar handgrip missing |2.1.1c| | 1 |
Rear Exhaust is leaking and excessively noisey |7.1.1b| | 1 |
Front Brake disc|s| excessively pitted |3.2.A1l| | 1 |
Rear Locking device|s| not correctly fitted which may make the motor bicycle dangerous to ride |6.2.1h| | 1 |
Exhaust excessively deteriorated |7.1.1a| | 1 |
Centre Rear Lower Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 1 |
Nearside Handlebar deformed |2.1.1b| | 1 |
Direction indicators flashing more than 120 times per minute |1.5.1c| | 1 |
Rear mono-shock pivot seized |2.4.B.4| | 1 |
Headlamp switch faulty |1.2.4| | 1 |
Exhaust has part of the system missing |7.1.1a| | 1 |
Nearside Handlebar deformed BENT |2.1.1b| | 1 |
Nearside Front Brake disc|s| has excessive run out |3.2.A1m| | 1 |
Offside Front Brake disc|s| has excessive run out |3.2.A1m| | 1 |
Centre Rear Lower Rear reflector on motorcycle missing |1.4.1| | 1 |
Rear Stop lamp damaged and function impaired |1.3.3a| | 1 |
Front Brake lever mounting insecure |3.1.2a| | 1 |
Front Front wheel bearings have excessive free play |2.3.5b| | 1 |
Front Front wheel bearings are excessively rough |2.3.5b| | 1 |
Centre Rear reflector on motorcycle missing |1.4.1| | 1 |
Rear Fuel tank leaking |7.2.1a| | 1 |
Front suspension has inadequate damping effect. |2.3.6c| | 1 |
Stop lamp affected by the operation of another lamp |1.3.2| | 1 |
Rear Stop lamp affected by the operation of another lamp |1.3.2| | 1 |
Rear position lamp adversely affected by the operation of another lamp |1.1.3b| | 1 |
Front wheel bearings have excessive free play |2.3.5b| | 1 |
Rear Brake lever has inadequate reserve travel |3.1.3b| | 1 |
Roller brake test No brake control achieves an efficiency of 30%. |3.3.A2a| | 1 |
Roller brake test Neither brake control achieves an efficiency of 25% |3.3.A2b| | 1 |
Nearside Rear Footrest insecure |6.2.1a| | 1 |
Exhaust mounting missing |7.1.1c| | 1 |
Front Headlamp aim beam image too far to the right |1.6.4| | 1 |
Offside Front Fuel tank leaking |7.2.1a| | 1 |
Fuel system component insecure |7.2.1b| | 1 |
Nearside Rear Lower Motorcycle structure excessively damaged |6.1.1a| | 1 |
Lower Front position lamp does not illuminate immediately when switched on |1.1.3a| | 1 |
Offside Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 1 |
Rear Roller brake test indicates a severely juddering brake |3.3.A1b| | 1 |
Drive chain sprocket carrier worn to excess |6.2.1e| | 1 |
Chain guard insecure |6.2.1c| | 1 |
Front Decelerometer brake test indicates a binding brake |3.3.E1d| | 1 |
Offside Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 1 |
Rear Stop lamp does not emit a steady light |1.3.1b| | 1 |
Nearside Steering control has Insufficient clearance at full lock affecting the riders grasp of handlebars |2.1.2b| | 1 |
Front Brake disc|s| has excessive run out |3.2.A1m| | 1 |
Offside Front Brake hose stretched by suspension movement |3.2.B3b| | 1 |
Nearside Front Direction indicator incorrect colour |1.5.1b| | 1 |
Offside Front Direction indicator incorrect colour |1.5.1b| | 1 |
Nearside Rear Direction indicator incorrect colour |1.5.1b| | 1 |
Offside Rear Direction indicator incorrect colour |1.5.1b| | 1 |
Brake disc|s| has excessive run out |3.2.A1m| | 1 |
Nearside Front Brake disc|s| cracked |3.2.A1g| | 1 |
Nearside Front Brake disc|s| excessively pitted |3.2.A1l| | 1 |
Offside Front Brake disc|s| excessively pitted |3.2.A1l| | 1 |
Nearside Front Brake disc|s| excessively scored |3.2.A1l| | 1 |
Offside Front Brake disc|s| excessively scored |3.2.A1l| | 1 |
Front wheel insecure Front |4.2.3b| | 1 |
Rear Plate brake test indicates a sticking brake |3.3.B1a| | 1 |
Indicator switch insecure |1.5.4| | 1 |
Exhaust is leaking and excessively noisey |7.1.1b| | 1 |
Rear Shock absorber has negligible damping effect |5.3.2 |b|| | 1 |
Fuel system component leaking |7.2.1a| | 1 |
Nearside Front Direction indicator not working |1.5.1c| | 1 |
Nearside Rear Direction indicator not working |1.5.1c| | 1 |
Rear Rear mono-shock pivot seized |2.4.B.4| | 1 |
Rear Exhaust noise is clearly in excess of that emitted by a similar motor bicycle fitted with a standard silencer in average condition |7.1.2| | 1 |
Floor brake test indicates a sticking brake |3.3.C2c| | 1 |
Rear Direction indicators not working |1.5.1c| | 1 |
Throttle operating incorrectly sticks open |6.2.1f| | 1 |
Exhaust mounting does not fully support the exhaust system Rear exhaust bolt missing |7.1.1.c| | 1 |
Centre Exhaust noise is clearly in excess of that emitted by a similar motor bicycle fitted with a standard silencer in average condition |7.1.2| | 1 |
Fuel system component leaking n/s carb |7.2.1a| | 1 |
Rear Brake disc|s| excessively worn |3.2.A1l| | 1 |
Offside Front Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Offside Handlebar deformed bent |2.1.1b| | 1 |
Nearside Front Lower Brake hose excessively kinked |3.2.B3a| | 1 |
Rear Floor brake test indicates a severely grabbing brake when turned by hand wheel stops at one point of rotation |3.3.C2d| | 1 |
Decelerometer brake test the less effective brake control does not achieve an efficiency of 25%. |3.3.E1b| | 1 |
Offside Front Shock absorber has a serious fluid leak |5.3.2 |b|| | 1 |
Nearside Front Handlebar handgrip not secure to handlebars. |2.1.1c| | 1 |
Offside Front Brake disc contaminated (1.1.14 (b)) | 1 |
Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Steering headbearing has excessive wear or free play (2.2.2 (f) (i)) | 1 |
Rear Stop lamp switch with a delay in operation (4.3.2 (a) (ii)) | 1 |
Rear Rear reflector missing (4.8.2 (a) (ii)) | 1 |
Headlamp aim so that beam "kick up" is not visible on the screen no pattern, incorrect headlight bulb fitted (4.1.2 (a)) | 1 |
Front Stop lamp does not illuminate by the operation of both brake controls (4.3.2 (a) (iii)) | 1 |
Fuel system component leaking carburetor (6.1.3 (b) (i)) | 1 |
Nearside Front Shock absorber has a serious fluid leak (5.3.2 (b)) | 1 |
Rear Brake excessively binding (1.2.1 (f)) | 1 |