Most common failures | No# failures |
---|
Headlamp aim out of alignment | 4 |
Headlamp aim beam image kick up to the offside |1.6| | 3 |
Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 3 |
Registration plate issues | 3 |
Exhaust is leaking and excessively noisey |7.1.1b| | 2 |
Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 2 |
Lower Exhaust is leaking and excessively noisey |7.1.1b| | 2 |
Rear shock absorber seal failed and leaking oil |2.4.A.1c| | 2 |
Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 2 |
Nearside Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Offside Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Front An item not tested |Manual| | 1 |
Locking device|s| not correctly fitted which may make the motor bicycle dangerous to ride |6.2.1h| | 1 |
Front Roller brake test indicates a binding brake |3.3.A1a| | 1 |
Front Roller brake test indicates excessive fluctuation of brake effort |3.3.A1d| | 1 |
Offside Front Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Steering movement excessively `notchy` with the weight on the lower bearing |2.2.1a| | 1 |
Rear Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 1 |
Centre Exhaust is leaking and excessively noisey |7.1.1b| | 1 |
Front Brake disc|s| excessively worn |3.2.A1l| | 1 |
Rear Locking devices not correctly fitted which may make the motor bicycle dangerous to ride |6.2.1h| | 1 |
Front Locking devices not correctly fitted which may make the motor bicycle dangerous to ride |6.2.1h| | 1 |
Centre Front Horn not working |1.7.3a| | 1 |
Nearside Rear Direction indicator not working |1.5.1c| | 1 |
Front Brake excessively binding (1.2.1 (f)) | 1 |
Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 1 |
Brake lever cannot be applied smoothly |3.1.3d| | 1 |
Front wheel bearings are excessively rough |2.3.5b| | 1 |
Steering movement excessively `notchy` with the wheel raised |2.2.1b| | 1 |
Rear Roller brake test indicates a sticking brake |3.3.A1a| | 1 |
Headlamp aim projected beam image obviously incorrect Kick up to offside - Headlamp mask fitted (4.1.2 (c)) | 1 |
Stop lamp does not illuminate by the operation of both brake controls Front brake light switch replaced (4.3.2 (a) (iii)) | 1 |
Rear Stop lamp remains on when the brake is released |1.3.1e| | 1 |
Throttle operating incorrectly Revs rising on R/H lock - cable adjusted (6.2.7 (a) (i)) | 1 |
Steering headbearing excessively stiff or notchy |2.2.2 |f| |i|| | 1 |
Rear Floor brake test indicates a binding brake |3.3.C2c| | 1 |
Nearside Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 1 |
Offside Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 1 |
Nearside Direction indicator flashing more than 120 times per minute |1.5.1c| | 1 |
Front Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 1 |
Front Brake component is excessively corroded piston in caliper seized --replaced on prs |3.1.5| | 1 |
Rear Brake component is excessively corroded spindle on operating arm seized--- freed off and lubricated |3.1.5| | 1 |
Fuel system component leaking fuel tap leaking---new tap fitted |7.2.1a| | 1 |
Exhaust is leaking and excessively noisey exhaust loose and leaking ---resealed and tightened |7.1.1b| | 1 |
Rear Brake lever has restricted free movement brake lever |1.1.15 |e|| | 1 |
Nearside Front Shock absorber has negligible damping effect |5.3.2 |b|| | 1 |
Offside Front Shock absorber has negligible damping effect |5.3.2 |b|| | 1 |
Stop lamp remains on when the brakes are released | 1 |
Front Stop lamp switch with a delay in operation |4.3.2 |a| |ii|| | 1 |
Front Headlamp aim so that beam "kick up" is not visible on the screen |4.1.2 |a|| | 1 |
Drive chain so loose it is likely to fail |6.1.7 |c| |ii|| | 1 |
Wheel alignment incorrect which adversely affects the steering |2.4 |a|| | 1 |