Most common failures | No# failures |
---|
Windscreen wiper does not clear the windscreen effectively | 11 |
Headlamp aim out of alignment | 10 |
Parking brake: efficiency below requirements |3.7.B.7| | 5 |
Registration plate lamp issues | 5 |
Brakes imbalanced across an axle | 4 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 4 |
Anti-lock braking system warning lamp indicates an ABS fault | 4 |
Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 4 |
Offside Headlamp not working on main beam |1.7.5a| | 2 |
Drivers seat insecure (6.2.5 (a) (ii)) | 2 |
Parking brake lever has no reserve travel |3.1.6b| | 2 |
Brake pedal has insufficient reserve travel (1.1.2 (a)) | 2 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 2 |
Brake pipe excessively corroded | 2 |
Nearside Front Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 2 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
Nearside Stop lamp|s| not working |4.3.1 |a| |ii|| | 2 |
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Offside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Front Body mounting fixings insecure Bolt loose (6.2.2 (c) (i)) | 1 |
Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
Nearside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
Offside Rear Outline marker lamp not working |4.2.1 |a|| | 1 |
Offside Front Upper Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
Rear brake disc in such a condition that it is seriously weakened | 1 |
Nearside Rear Leaf spring has excessive wear in a shackle pin and/or bush |2.4.B.2| | 1 |
Nearside Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
Supplementary Restraint System warning lamp indicates a fault |5.4.2| | 1 |
Nearside Front Valve stem seriously damaged |4.1.D.1e| | 1 |
Direction indicator adversely affected by the operation of another lamp Aux Lights at Front Working with Hazards (4.4.3 (b)) | 1 |
Nearside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Fuel tank insecure Tank Strap Broken (6.1.3 (a) (i)) | 1 |
Front Body has a sharp edge caused by corrosion bonnet front edge holed corroded. |6.1.C.1| | 1 |
Nearside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance very dim |1.1.A.3d| | 1 |
Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
Offside Rear Brake cable has restricted free movement |1.1.15 |e|| | 1 |
Nearside Parking brake inoperative on one side |1.4.1 |a|| | 1 |
Offside Parking brake inoperative on one side |1.4.1 |a|| | 1 |
Offside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
Parking brake efficiency less than 50% of the required value |1.4.2 |a| |ii|| | 1 |
Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Close to suspension arm front sub frame to chassis (5.3.6 (a) (i)) | 1 |
Nearside Rear Service brake lagging in operation (1.2.1 (d)) | 1 |
Braking system leaking rear master cylinder leaking |3.6.A.1| | 1 |
Nearside Front Brake performance not tested N/S/F wheel brake caliper seized unable to turn (1.2.1 (g)) | 1 |
Offside Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Front passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
Front passenger door cannot be opened from inside the vehicle (6.2.3 (a)) | 1 |
Offside Stop lamp not working |1.2.1b| | 1 |
Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting in bonnet (6.2.2 (d) (i)) | 1 |
Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting marked yellow (6.2.2 (d) (i)) | 1 |
Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting next to spring mounting (6.2.2 (d) (i)) | 1 |
Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced arch (6.1.1 (c) (i)) | 1 |
Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sill (6.1.1 (c) (i)) | 1 |
Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
rear parking |secondary| brakes imbalanced | 1 |
Offside Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Inner Suspension component mounting prescribed area is excessively corroded wheel arch |2.4.A.3| | 1 |
Nearside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Brake fluid warning lamp illuminated |3.6.G.2| | 1 |
Brake master cylinder leaking (1.1.10 (b) (ii)) | 1 |
Offside Rear Position lamp has a product on the lens or light source which shows white light to the rear (4.2.3 (b) (ii)) | 1 |
Nearside Rear Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
Offside Rear Outline marker lamp missing (4.2.1 (a) (ii)) | 1 |
Horn not working (7.7 (a) (ii)) | 1 |
Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Nearside Headlamp aim not tested |1.8.A.1c| | 1 |
Horn not working |1.6.2a| | 1 |
Offside Front Electrical wiring deteriorated and bare connector exposed at inner wing air box area |1.9.2c| | 1 |
Brake hose has insufficient room to move | 1 |
Offside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Offside Front Inner Brake master cylinder/servo mounting prescribed area is excessively corroded wing at servo/master area |3.6.C.3| | 1 |
Offside Front Front suspension has excessive movement at a suspension ball joint |2.5.A.1c| | 1 |
Front brake application uneven | 1 |
front brakes release unevenly |3.7.B.4| | 1 |
Rear brake application uneven | 1 |
Nearside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wing at subframe mounting |6.1.B.2| | 1 |
Nearside Front Body has a sharp edge caused by damage indicator lamp |6.1.C.1| | 1 |
Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
Front drive shaft support bearing excessively worn |2.5.C.2c| | 1 |
Service brake: efficiency below requirements |3.7.B.7| | 1 |
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings above rear axle (6.1.B.2) | 1 |
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings above rear axle (6.1.B.2) | 1 |
Nearside Rear Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings tail lift mounting (6.1.B.2) | 1 |
Offside Rear Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings tail lift mounting (6.1.B.2) | 1 |
Parking brake lever has no reserve travel (3.1.6b) | 1 |
Nearside Rear rear brake recording little or no effort (3.7.B.5a) | 1 |
Brake fluid warning lamp illuminated (3.6.G.2) | 1 |
Headlamp aim not tested (1.8.A.1c) | 1 |
All position lamps not working (1.1.A.3b) | 1 |
Battery insecure (1.9.1) | 1 |
Offside Rear Rear position lamp(s) insecure (1.1.A.3a) | 1 |
Nearside Front Power steering pipe(s) or hose(s) leaking from a seal (2.3.3b) | 1 |
Nearside Front Torsion bar excessive play at an end fixing (2.4.E.2) | 1 |
Offside Front Torsion bar excessive play at an end fixing (2.4.E.2) | 1 |
Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
Drivers view of the road through the swept area of the windscreen materially affected by an obstruction (3.1 (a) (ii)) | 1 |
Nearside Front All position lamps not working (4.2.1 (a)) | 1 |
Front Upper All outline marker lamps not working (4.2.1 (a)) | 1 |
Rear Upper All outline marker lamps not working (4.2.1 (a)) | 1 |
Offside Rear All position lamps not working (4.2.1 (a)) | 1 |
Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Speedometer cannot be illuminated (7.8 (c) (ii)) | 1 |
Nearside Front Upper Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
Nearside Front Upper Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Offside Front Upper Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Nearside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Rear fog lamp not working |1.3.2b| | 1 |
Offside Rear Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
Nearside Front Lower Direction indicator incorrect colour |1.4.A.2f| | 1 |
Offside Front Lower Direction indicator incorrect colour |1.4.A.2f| | 1 |
Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings door step |6.1.B.2| | 1 |
Additional braking device insecure Air Tank Strap Broken |3.6.I.1| | 1 |
Braking system leaking Main Rear Brake Chamber Leaking |3.6.A.1| | 1 |
Offside Front Seat belt anchorage prescribed area is excessively corroded Cab Floor |5.2.6| | 1 |
Offside Front Upper Position lamp not working (4.2.1 (a) (ii)) | 1 |
Drag link end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Nearside Rear Suspension bellows damaged or deteriorated and function affected (5.3.5 (b) (i)) | 1 |
Offside Rear Upper Position lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Fuel tank insecure (6.1.3 (a) (i)) | 1 |
Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Supplementary restraint system warning lamp indicates a fault |7.1.6 |a|| | 1 |
Nearside Side repeater incorrect colour |4.4.3 |a|| | 1 |
Offside Side repeater incorrect colour |4.4.3 |a|| | 1 |
Rear Position lamp switch allows the rear position lamps to be switched off when the headlamps are on |4.2.2 |a|| | 1 |
Offside Rear Position lamp not working |4.2.1 |a| |ii|| | 1 |
Fuel tank insecure |6.1.3 |a| |i|| | 1 |
Nearside Front Lower Suspension arm ball joint excessively worn |5.3.4 |a| |i|| | 1 |
Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
Offside Exhaust emissions exceed level of metered smoke for a turbo charged engine (8.2.2.2 (b)) | 1 |
Offside Exhaust emissions exceed manufacturers specified limit (8.2.2.2 (a)) | 1 |
Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner arch (6.2.2 (d) (i)) | 1 |
Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner arch (6.2.2 (d) (i)) | 1 |
Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Side repeater incorrect colour (4.4.3 (a)) | 1 |
Nearside Front Lower Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Offside Front Upper Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength INNER WHEEL ARCH AREA (5.3.6 (a) (i)) | 1 |
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength INNER WHEEL ARCH AREA (5.3.6 (a) (i)) | 1 |
Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill / outrigger (6.2.2 (d) (i)) | 1 |
Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting in wheel arch (6.2.2 (d) (i)) | 1 |
Brake performance not tested brake pipe bust when doing brake test (1.2.1 (g)) | 1 |
Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
Nearside Front Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
Offside Front Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
Stop lamp|s| all not working |4.3.1 |a| |iii|| | 1 |
Battery insecure |1.9.1| | 1 |
Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Offside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
Rear fog lamp switch inoperative (4.5.3 (a)) | 1 |
Windscreen wiper not working (3.4 (a)) | 1 |
Windscreen washer not working | 1 |
Offside Front Leaf spring main leaf fractured |5.3.1 |b| |ii|| | 1 |
Front Exhaust has a major leak of exhaust gases major leak after manifold |6.1.2 |a|| | 1 |