Most common failures | No# failures |
---|
Headlamp aim out of alignment | 23 |
Drive chain excessively loose |6.2.1d| | 16 |
Rear Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 15 |
Horn not working |1.7.3a| | 12 |
Registration plate issues | 9 |
Drive chain worn to excess |6.2.1e| | 9 |
Rear Roller brake test indicates a binding brake |3.3.A1a| | 9 |
Front Roller brake test indicates a binding brake |3.3.A1a| | 9 |
Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 8 |
Front Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 7 |
Rear Drive chain sprocket worn to excess |6.2.1e| | 7 |
Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 7 |
Nearside Handlebar handgrip not secure to handlebars. |2.1.1c| | 7 |
Rear reflector on motorcycle missing |1.4.1| | 7 |
Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 6 |
Roller brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.A2b| | 6 |
Registration plate lamp issues | 5 |
Nearside Front Direction indicator not working |1.5.1c| | 4 |
Locking device|s| not correctly fitted which may make the motor bicycle dangerous to ride |6.2.1h| | 4 |
Rear wheel bearings have excessive free play |2.4.A.2c| | 4 |
Nearside Front shock absorber seal failed and leaking oil |2.3.3| | 4 |
Nearside Rear Direction indicator not working |1.5.1c| | 4 |
Nearside Rear Footrest missing |6.2.1a| | 4 |
Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 4 |
Rear Brake pedal is inoperative |3.1.3c| | 4 |
Nearside Rear Direction indicators not working |1.5.1c| | 3 |
Headlamp not working on main beam (4.1.1 (a) (ii)) | 3 |
Steering movement excessively `notchy` with the weight on the lower bearing |2.2.1a| | 3 |
Steering movement excessively `notchy` with the wheel raised |2.2.1b| | 3 |
Rear Exhaust mounting does not fully support the exhaust system |7.1.1.c| | 3 |
Front Brake excessively binding (1.2.1 (f)) | 3 |
Rear Brake excessively binding (1.2.1 (f)) | 3 |
Headlamp aim headlamp deteriorated and function impaired |1.2.3a| | 3 |
Exhaust is leaking and excessively noisey |7.1.1b| | 3 |
Direction indicators flashing more than 120 times per minute |1.5.1c| | 3 |
Drive chain excessively tight |6.2.1d| | 3 |
Horn not working (7.7 (a) (ii)) | 3 |
Horn not loud enough to be heard by another road user |1.7.3a| | 3 |
Rear Wheel bearing play so excessive it is likely to break up |5.1.3 |a| |ii|| | 3 |
Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 3 |
Offside Front Direction indicator incorrect colour |1.5.1b| | 3 |
Throttle has a significant change in engine speed whilst moving the steering from lock to lock |2.1.4| | 3 |
Offside Front Direction indicator missing |1.5.1a| | 3 |
Nearside Front Direction indicators not working |1.5.1c| | 3 |
Offside Handlebar handgrip not secure to handlebars. |2.1.1c| | 3 |
Nearside Front Shock absorber has a serious fluid leak (5.3.2 (b)) | 2 |
Wheel alignment incorrect which adversely affects the handling |2.5.1| | 2 |
Rear Drive chain worn to excess |6.2.1e| | 2 |
Offside Front Direction indicator damaged and function impaired |1.5.3a| | 2 |
Exhaust noise is clearly in excess of that emitted by a similar motor bicycle fitted with a standard silencer in average condition |7.1.2| | 2 |
Front Brake excessively binding |1.2.1 |f|| | 2 |
Front Roller brake test indicates a sticking brake |3.3.A1a| | 2 |
Offside Front shock absorber seal failed and leaking oil |2.3.3| | 2 |
Steering operation restricted in free movement from lock to lock |2.1.4 |c|| | 2 |
Rear Brake disc|s| excessively scored |3.2.A1l| | 2 |
Central Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 2 |
Drive chain so loose it is likely to fail |6.1.7 |c| |ii|| | 2 |
Rear Brake pedal has inadequate reserve travel |3.1.3b| | 2 |
Exhaust mounting does not fully support the exhaust system |7.1.1.c| | 2 |
Steering control has Insufficient clearance at full lock affecting the riders grasp of handlebars |2.1.2b| | 2 |
Stop lamp remains on when the brake is released |1.3.1e| | 2 |
Headlamp at least one does not illuminate on main beam |1.2.2a|ii|| | 2 |
Rear reflector missing (4.8.2 (a) (ii)) | 2 |
Roller brake test Neither brake control achieves an efficiency of 25% |3.3.A2b| | 2 |
Front position lamp does not illuminate immediately when switched on |1.1.3a| | 2 |
Front Plate brake test indicates a binding brake |3.3.B1a| | 2 |
Headlamp insecure |1.2.3b| | 2 |
Offside Front Direction indicators not working |1.5.1c| | 2 |
Rear Rear reflector on motorcycle missing |1.4.1| | 2 |
Rear Wheel alignment incorrect which adversely affects the handling |2.5.1| | 2 |
Offside Front Shock absorber has a serious fluid leak (5.3.2 (b)) | 1 |
Brake hose damaged | 1 |
Steering operation restricted in free movement from lock to lock (2.1.4 (c)) | 1 |
Footrest missing rear right hand |6.2.12 |a|| | 1 |
Motorcycle structure has a fracture which is likely to adversely affect braking or steering inner bodywork of fairing |6.1.1 |a| |ii|| | 1 |
Offside Throttle has a significant change in engine speed whilst moving the steering from lock to lock |2.1.4| | 1 |
Nearside Handlebar mounting clamp bolt loose |2.1.1a| | 1 |
Offside Handlebar mounting clamp bolt loose |2.1.1a| | 1 |
Offside Steering control has Insufficient clearance at full lock affecting the riders grasp of handlebars |2.1.2b| | 1 |
Steering headbearing in such a condition that steering control is adversely affected |2.2.2 |f| |ii|| | 1 |
Nearside Front position lamp missing |1.1.1a| | 1 |
Offside Front position lamp missing |1.1.1a| | 1 |
Rear Brake caliper|s| insecure |3.2.A1j| | 1 |
Rear Brake caliper|s| securing bolt|s| missing |3.2.A1j| | 1 |
Rear Brake disc|s| excessively worn |3.2.A1l| | 1 |
Rear Brake master cylinder insecurely mounted |3.2.B1a| | 1 |
Rear Position lamp not working (4.2.1 (a)) | 1 |
Headlamp aim headlamp damaged and function impaired |1.2.3a| | 1 |
Rear suspension component seized |2.4A2a|ii|| | 1 |
Indicator tell tale not functioning |1.5.2| | 1 |
Nearside Front Direction indicator insecure |1.5.3b| | 1 |
Fairing insecure and likely to impede the steering |2.1.2e| | 1 |
Steering control handlebar movement restricted by taut cables |2.1.2c| | 1 |
Rear Stop lamp not working not working on rear brake pedal (4.3.1 (a) (ii)) | 1 |
Front Brake lever is so short that the brake cannot be readily applied (1.1.2 (d)) | 1 |
Drive chain sprocket excessively loose bolt missing (6.1.7 (c) (i)) | 1 |
Offside Rear Direction indicator not working |1.5.1c| | 1 |
Nearside Rear Direction indicator flashing more than 120 times per minute |1.5.1c| | 1 |
Steering headbearing has excessive wear or free play headstock nut loose |2.2.2 |f| |i|| | 1 |
Steering operation fouling on the fuel tank or bodywork on full lock brake lever applied on full lock |2.1.4 |b|| | 1 |
Steering operation fouling on the fuel tank or bodywork on full lock full lock not achieved |2.1.4 |b|| | 1 |
Rear reflector missing |4.8.2 |a| |ii|| | 1 |
Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Headlamp insecure Fairing bracket loose |4.1.1 |c|| | 1 |
Suspension arm mounting modified so the suspension is likely to fail other components r/h footrest fouling swingarm |5.3.3 |c| |ii|| | 1 |
Fuel tank insecure |6.1.3 |a| |i|| | 1 |
Front suspension has excessive stiffness in the suspension movement. |2.3.6b| | 1 |
Rear Roller brake test indicates brake effort rise disproportional to brake lever or pedal effort |3.3.A1c| | 1 |
Lower Rear mono-shock pivot excessively worn |2.4.B.4| | 1 |
Indicator switch insecure |1.5.4| | 1 |
Front Floor brake test indicates a binding brake |3.3.C2c| | 1 |
Central Rear Rear reflector missing missing and placed it (4.8.2 (a) (ii)) | 1 |
Horn sounds harsh or grating |1.7.3c| | 1 |
Rear reflector on motorcycle deteriorated and function impaired |1.4.2a| | 1 |
Roller brake test indicates a binding brake |3.3.A1a| | 1 |
Steering control fouling between components which interferes with the free movement of the steering |2.1.2a| | 1 |
Indicator switch defective |1.5.4| | 1 |
Nearside Front Handlebar deformed |2.1.1b| | 1 |
Rear Suspension component pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
Rear Brake master cylinder has a seized master cylinder pivot. |3.2.B5| | 1 |
Front Exhaust mounting does not fully support the exhaust system |7.1.1.c| | 1 |
Front Horn not loud enough to be heard by another road user |1.7.3a| | 1 |
Nearside Front Direction indicator damaged and function impaired |1.5.3a| | 1 |
Headlamp aim not tested |4.1.2 |b|| | 1 |
Dipswitch does not operate immediately when selected on dipped beam |4.1.3 |b|| | 1 |
Fuel cap does not fasten securely maintaining the sealing arrangement |7.2.2b| | 1 |
Fuel cap sealing washer deteriorated |7.2.2c| | 1 |
Lower Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 1 |
Headlamp damaged and function impaired |1.2.3a| | 1 |
Steering lock stop maladjusted |2.1.3| | 1 |
Front Front position lamp missing |1.1.1a| | 1 |
Steering control has Insufficient clearance at full lock affecting the riders operation of the controls |2.1.2b| | 1 |
Throttle operating incorrectly switch and throttle only cable tied on handlebars very loose |6.2.1f| | 1 |
Central Front Lower Valve stem seriously damaged (5.2.3 (j)) | 1 |
Rear Brake pedal attachment screws loose |3.1.2b| | 1 |
Fairing so located that it is likely to impede the steering |2.1.2e| | 1 |
Rear Shock absorber has negligible damping effect |5.3.2 |b|| | 1 |
Offside Front Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 1 |
Fuel cap does not fasten securely by a positive means |7.2.2b| | 1 |
Nearside Front Footrest insecure |6.2.1a| | 1 |
Front suspension assembly component loose |2.3.1| | 1 |
Offside Rear Footrest insecure |6.2.1a| | 1 |
Front Brake linkage has abnormal movement due to excessive wear |3.2.A1i| | 1 |
Rear reflector on motorcycle deteriorated and function impaired Reflector not red |1.4.2a| | 1 |
Stop lamp does not illuminate by the operation of both brake controls (4.3.2 (a) (iii)) | 1 |
Nearside Steering control has Insufficient clearance at full lock affecting the riders grasp of handlebars |2.1.2b| | 1 |
Rear Floor brake test indicates a binding brake |3.3.C2c| | 1 |
Front Brake lever mounting insecure |3.1.2a| | 1 |
Rear Brake fluid reservoir fluid level dangerously low |3.2.B1d| | 1 |
Front Brake disc|s| friction surface contaminated by oil or grease |3.2.A1k| | 1 |
Roller brake test No brake control achieves an efficiency of 30%. |3.3.A2a| | 1 |
Rear Drive chain excessively loose |6.2.1d| | 1 |
Rear Stop lamp not working (4.3.1 (a) (ii)) | 1 |
Drive chain excessively loose (6.1.7 (c) (i)) | 1 |
Wheel alignment incorrect which adversely affects the handling (2.4 (a)) | 1 |
Nearside Front Direction indicator incorrect colour |1.5.1b| | 1 |
Rear suspension bush excessively deteriorated |2.4.A2a|i|| | 1 |
Exhaust markings indicating not for road use or similar wording |7.1.4| | 1 |
Nearside Indicator switch defective |1.5.4| | 1 |
Front Indicator tell tale not functioning |1.5.2| | 1 |
Brake hose excessively deteriorated | 1 |
Front wheel spindle securing nut locking device missing |2.3.3a| | 1 |
Offside Front Roller brake test indicates brake effort rise disproportional to brake lever or pedal effort |3.3.A1c| | 1 |
Outer Front Roller brake test indicates a sticking brake |3.3.A1a| | 1 |
Handlebar deformed |2.1.1b| | 1 |
Throttle operating incorrectly |6.2.1f| | 1 |
Plate brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.B2b| | 1 |
Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
Stop lamp not working on both front and rear brake levers (4.3.1 (a) (ii)) | 1 |
Drive chain excessively tight (6.1.7 (k) (i)) | 1 |
Nearside Rear Direction indicator obscured |1.5.1a| | 1 |
Offside Rear Direction indicator obscured |1.5.1a| | 1 |
Nearside Handlebar mounting clamp loose |2.1.1a| | 1 |
Wheel alignment incorrect which adversely affects the steering |2.5.1| | 1 |
Nearside Front Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Offside Front Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Rear Headlamp at least one does not illuminate on main beam |1.2.2a|ii|| | 1 |
Stop lamp not working foot pedal (4.3.1 (a) (ii)) | 1 |
Offside Front Footrest insecure |6.2.1a| | 1 |
Rear Stop lamp remains on when the brake is released |1.3.1e| | 1 |
Brake performance not tested |3.3| | 1 |
Rear suspension bearing has excessive free play |2.4.A2a|i|| | 1 |
Rear shock absorber seal failed and leaking oil |2.4.A.1c| | 1 |
Rear Roller brake test indicates brake effort fall disproportional to brake lever or pedal effort |3.3.A1c| | 1 |
Rear Rear wheel bearings have excessive free play |2.4.A.2c| | 1 |
Front Drive chain sprocket worn to excess |6.2.1e| | 1 |
Offside Handlebar grip insecure to handlebar (2.2.1 (d) (ii)) | 1 |
Footrest missing |6.2.1a| | 1 |
Rear Brake cylinder severely corroded |3.2.B1b| | 1 |
Offside Front Direction indicators flashing more than 120 times per minute |1.5.1c| | 1 |
Nearside Front Direction indicators flashing more than 120 times per minute |1.5.1c| | 1 |
Offside Rear Brake disc|s| cracked |3.2.A1g| | 1 |
Headlamp main beam affected by the operation of another lamp |1.2.2c| | 1 |
Front Brake hose is likely to be fouled or trapped by moving parts |3.2.B2c| | 1 |
Front Brake component has restricted free movement and operation is likely to be impeded |3.2.A1h| | 1 |
Offside Handlebar cracked |2.1.1b| | 1 |
Rear Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 1 |
Rear Brake disc|s| cracked |3.2.A1g| | 1 |
Stop lamp not working |4.3.1 |a| |ii|| | 1 |
Front Brake caliper|s| insecure calliper fitted incorrectly |3.2.A1j| | 1 |
Front Front position lamp incorrect colour |1.1.2a| | 1 |
Front Roller brake test indicates a severely grabbing brake |3.3.A1b| | 1 |
Front Roller brake test indicates excessive fluctuation of brake effort |3.3.A1d| | 1 |
Headlamp switch faulty |1.2.4| | 1 |
Indicator switch does not operate the direction indicators on the side selected |1.5.4| | 1 |
Nearside Front Direction indicator missing |1.5.1a| | 1 |
Front Steering control handlebar movement restricted by trapped cables |2.1.2c| | 1 |
Rear suspension bush has excessive free play |2.4.A2a|i|| | 1 |
Offside Front Direction indicator insecure |1.5.3b| | 1 |
Rear Hydraulic brake control feels spongy |3.1.4a| | 1 |
Front Direction indicator incorrect colour |1.5.1b| | 1 |
Steering movement excessively stiff with the wheel raised |2.2.1b| | 1 |
Riders seat insecure |6.2.1a| | 1 |
Front Brake disc|s| excessively worn |3.2.A1l| | 1 |
Front Brake lever has inadequate reserve travel |3.1.3b| | 1 |
Offside Front Upper Fairings so located that it is likely to impede the steering |2.1.2e| | 1 |
Rear position lamp damaged and function impaired |1.1.1b| | 1 |
An item not tested |Manual| | 1 |
Nearside Direction indicator flashing more than 120 times per minute |1.5.1c| | 1 |
Front Brake disc|s| excessively scored |3.2.A1l| | 1 |
Front Stop lamp does not illuminate by the operation of both brake controls (4.3.2 (a) (iii)) | 1 |
Fuel tank insecure (6.1.3 (a) (i)) | 1 |
Front Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 1 |
Nearside Rear Direction indicator incorrect colour |1.5.1b| | 1 |
Rear reflector on motorcycle does not reflect squarely to the rear |1.4.1| | 1 |
Exhaust noise is clearly in excess of that emitted by a similar motorcycle fitted with a standard silencer in average condition (8.1.1 (a)) | 1 |