Most common failures | No# failures |
---|
Headlamp aim out of alignment | 10 |
Front Roller brake test indicates a binding brake |3.3.A1a| | 6 |
Front Floor brake test indicates a binding brake |3.3.C2c| | 5 |
Stop lamp remains on when the brakes are released | 4 |
Front Brake excessively binding |1.2.1 |f|| | 3 |
Front Roller brake test indicates excessive fluctuation of brake effort |3.3.A1d| | 2 |
Roller brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.A2b| | 2 |
Front Brake fluid reservoir fluid level dangerously low |3.2.B1d| | 2 |
Rear Roller brake test indicates a binding brake |3.3.A1a| | 2 |
Front Floor brake test indicates a sticking brake |3.3.C2c| | 2 |
Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 2 |
Headlamp aim so that beam "kick up" is not visible on the screen (4.1.2 (a)) | 2 |
Rear Stop lamp insecure |1.3.3b| | 2 |
Rear Brake lever has insufficient reserve travel (1.1.2 (a)) | 2 |
Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 2 |
Offside Front shock absorber seal failed and leaking oil |2.3.3| | 2 |
Front Brake disc|s| excessively worn |3.2.A1l| | 2 |
Nearside Front Front shock absorber seal failed and leaking oil |2.3.3| | 2 |
Front Front wheel bearings are excessively rough |2.3.5b| | 1 |
Rear Brake lining|s| less than 1.5 mm thick |3.2.A1f|i|| | 1 |
Stop lamp does not illuminate by the operation of both brake controls (4.3.2 (a) (iii)) | 1 |
Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Front position lamp does not illuminate immediately when switched on |1.1.3a| | 1 |
Rear Stop lamp switch with a delay in operation (4.3.2 (a) (ii)) | 1 |
Front Brake excessively binding (1.2.1 (f)) | 1 |
Front Steering headbearing has excessive free play |2.2.2| | 1 |
Riders seat insecure |6.2.1a| | 1 |
Brake lever mounting insecure |3.1.2a| | 1 |
Nearside Rear shock absorber seal failed and leaking oil |2.4.A.1c| | 1 |
Offside Rear shock absorber seal failed and leaking oil |2.4.A.1c| | 1 |
Rear Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 1 |
Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Rear Brake grabbing severely (1.2.1 (c)) | 1 |
Front Throttle operating incorrectly |6.2.1f| | 1 |
Front wheel bearings are excessively rough cant test as front brake binding |2.3.5b| | 1 |
Front Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 1 |
Exhaust mounting missing |7.1.1c| | 1 |
Rear Rear reflector missing (4.8.2 (a) (ii)) | 1 |
Rear Brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
Front Dipswitch does not operate immediately when selected on dipped beam (4.1.3 (b)) | 1 |
Steering headbearing has excessive wear or free play (2.2.2 (f) (i)) | 1 |
Nearside Front Indicator tell tale not functioning |1.5.2| | 1 |
Front Brake lever is bent and the brake cannot be readily applied |3.1.3c| | 1 |
Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Steering headbearing has excessive free play |2.2.2| | 1 |
Front Stop lamp not working (4.3.1 (a) (ii)) | 1 |
Stop lamp does not emit a steady light |1.3.1b| | 1 |
Front Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Front Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 1 |
Front Handlebar mounting clamp bolt loose |2.1.1a| | 1 |
Front Front position lamp does not illuminate immediately when switched on |1.1.3a| | 1 |
Rear reflector on motorcycle missing |1.4.1| | 1 |
Roller brake test No brake control achieves an efficiency of 30%. |3.3.A2a| | 1 |
Rear Position lamp not working |4.2.1 |a|| | 1 |
Rear Valve stem seriously damaged Leaking. (5.2.3 (j)) | 1 |
Nearside Rear Brake lever has insufficient reserve travel (1.1.2 (a)) | 1 |
Nearside Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 1 |
Offside Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 1 |
Rear Rear reflector on motorcycle obscured |1.4.1| | 1 |
Rear Wheel hub worn to the extent that wheel security is adversely affected (5.2.1 (b) (ii)) | 1 |
Front Stop lamp remains on when the brake is released |1.3.1e| | 1 |
Rear Stop lamp remains on when the brake is released |1.3.1e| | 1 |
Nearside Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Roller brake test indicates excessive fluctuation of brake effort |3.3.A1d| | 1 |
Rear Brake lever insecure |1.1.2 |e| |i|| | 1 |
Rear Brake lever is damaged and the brake cannot be readily applied |3.1.3c| | 1 |
Front Plate brake test indicates a sticking brake |3.3.B1a| | 1 |
Plate brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.B2b| | 1 |
Rear Brake lever has inadequate reserve travel |3.1.3b| | 1 |
Front Roller brake test indicates a sticking brake |3.3.A1a| | 1 |
Rear reflector on motorcycle obscured |1.4.1| | 1 |
Rear Brake lagging in operation (1.2.1 (d)) | 1 |
Nearside Front Brake disc|s| friction surface contaminated by oil or grease |3.2.A1k| | 1 |