| Most common failures | No# failures |
|---|
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 13 |
| Headlamp aim out of alignment | 13 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 12 |
| Windscreen wiper does not clear the windscreen effectively | 10 |
| Rear brake binding | 8 |
| Parking brake: efficiency below requirements |3.7.B.7| | 8 |
| Brakes imbalanced across an axle | 7 |
| Windscreen washer not working | 5 |
| Registration plate lamp issues | 5 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 5 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 5 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Mechanical brake component has restricted free movement | 5 |
| Rear parking brake recording little or no effort | 5 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Brake pipe excessively corroded | 4 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 4 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 3 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Rear Mechanical brake component has restricted free movement | 3 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 3 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 3 |
| Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 3 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 2 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 2 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Stop lamp not working |1.2.1b| | 2 |
| Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
| Offside Rear Shock absorbers has a serious fluid leak | 2 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 2 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside front brake binding |3.7.B.1| | 2 |
| Parking brake lever has no reserve travel |3.1.6b| | 2 |
| Nearside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Registration plate issues | 2 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor (5.3.6 (a) (i)) | 1 |
| Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Offside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Brake performance not tested (1.2.1 (g)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Exhaust emissions - engine idle speed too high (8.2.1.2 (e)) | 1 |
| Central Exhaust has a major leak of exhaust gases blowing and holed (6.1.2 (a)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Rear Service brake lagging in operation (1.2.1 (d)) | 1 |
| Nearside Rear Service brake lagging in operation (1.2.1 (d)) | 1 |
| Offside Rear Inner Body mounting fixings insecure sill to outer sill not fully welded (6.2.2 (c) (i)) | 1 |
| Centre Rear Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
| Nearside Indicator switch faulty |1.4.A.1| | 1 |
| Offside Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Horn not working |1.6.2a| | 1 |
| Nearside Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
| Offside Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
| Offside Front Direction indicator not working |1.4.A.2c| | 1 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 1 |
| Nearside Rear Service brake excessively binding |1.2.1 |f|| | 1 |
| Offside Headlamp insecure |4.1.1 |c|| | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Lower Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Front Lower Ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Windscreen wiper missing (3.4 (a)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect both (4.1.2 (c)) | 1 |
| Brake hose excessively deteriorated | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength subframe fractured (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill going into arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength top strut mount area (5.3.6 (a) (i)) | 1 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Exhaust emissions hydrocarbon content excessive |8.2.1.2 |b|| | 1 |
| Exhaust emissions carbon monoxide content excessive |8.2.1.2 |b|| | 1 |
| Offside Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
| Offside Front Seat belt anchorage prescribed area is fractured |5.2.6| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
| Exhaust has a major leak of exhaust gases back box joiner (6.1.2 (a)) | 1 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Nearside Rear Upper Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Upper Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer (5.3.6 (a) (i)) | 1 |
| Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Nearside Front Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Stop lamp not working |1.2.1b| | 1 |
| Braking system leaking |3.6.A.1| | 1 |
| Nearside front brake binding |3.7.B.1| | 1 |
| Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
| Offside Rear An item not tested |Manual| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
| Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Bonnet cannot be secured in the closed position |8.4.1| | 1 |
| Nearside Suspension component mounting prescribed area is inadequately repaired outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength suspension mount (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure is cracked, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Centre Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is severely distorted |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is severely distorted |2.4.A.3| | 1 |
| Horn control insecure |1.6.1| | 1 |
| Windscreen has damage | 1 |
| Nearside Front Lower Suspension arm locating pin retaining device not properly locked |2.4.G.3b| | 1 |
| Offside Outer Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Front brake disc excessively pitted |3.5.1h| | 1 |
| Nearside Front front brake juddering severely |3.7.A.2b| | 1 |
| Nearside Rear An item not tested |Manual| | 1 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Driver`s seat insecure |6.2.A.1| | 1 |
| Rear brake application uneven | 1 |
| Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 1 |
| Nearside Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Brake cable has restricted free movement (1.1.15 (e)) | 1 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Rear Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |