Most common failures | No# failures |
---|
Headlamp aim out of alignment | 48 |
Registration plate issues | 24 |
Rear Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 18 |
Rear reflector on motorcycle missing |1.4.1| | 15 |
Front Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 14 |
Drive chain excessively loose |6.2.1d| | 12 |
Registration plate lamp issues | 12 |
Front Roller brake test indicates a binding brake |3.3.A1a| | 10 |
Drive chain worn to excess |6.2.1e| | 9 |
Windscreen wiper does not clear the windscreen effectively | 8 |
Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 8 |
Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 7 |
Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 6 |
Rear reflector missing |4.8.2 |a| |ii|| | 6 |
Rear fog lamp missing |1.3.2a| | 5 |
Front shock absorber seal failed and leaking oil |2.3.3| | 5 |
Rear Brake disc|s| excessively worn |3.2.A1l| | 5 |
Steering headbearing has excessive free play |2.2.2| | 5 |
Front Brake disc|s| excessively worn |3.2.A1l| | 5 |
Nearside Front shock absorber seal failed and leaking oil |2.3.3| | 4 |
Offside Front shock absorber seal failed and leaking oil |2.3.3| | 4 |
Brake pipe excessively corroded | 4 |
Horn missing |1.7.1| | 4 |
Horn not working |1.7.3a| | 4 |
Roller brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.A2b| | 4 |
Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 4 |
Nearside Front position lamp|s| incorrect colour |1.1.A.3e| | 3 |
Rear reflector on motorcycle obscured |1.4.1| | 3 |
Anti-lock braking system warning lamp indicates an ABS fault | 3 |
Throttle has a significant change in engine speed whilst moving the steering from lock to lock |2.1.4| | 3 |
Front wheel bearings have excessive free play |2.3.5b| | 3 |
Rear wheel bearings have excessive free play |2.4.A.2c| | 3 |
Steering movement excessively `notchy` with the weight on the lower bearing |2.2.1a| | 3 |
Front Roller brake test indicates excessive fluctuation of brake effort |3.3.A1d| | 3 |
Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 3 |
Front Brake disc|s| is excessively distorted |3.2.A1m| | 3 |
Offside Front Front shock absorber seal failed and leaking oil |2.3.3| | 3 |
Rear Brake lever has inadequate reserve travel |3.1.3b| | 3 |
Throttle operating incorrectly |6.2.1f| | 3 |
Steering movement excessively `notchy` with the wheel raised |2.2.1b| | 3 |
Front Stop lamp not working (4.3.1 (a) (ii)) | 3 |
Offside Front Shock absorber has a serious fluid leak (5.3.2 (b)) | 3 |
Rear reflector missing (4.8.2 (a) (ii)) | 3 |
Offside Front position lamp|s| incorrect colour |1.1.A.3e| | 2 |
Rear fog lamp switch missing |1.3.1a| | 2 |
Offside Rear fog lamp missing |1.3.2a| | 2 |
Front Headlamp aim beam image kick up to the offside |1.8| | 2 |
Offside Rear fog lamp emits a light other than red |1.3.2e| | 2 |
Rear Rear reflector on motorcycle missing |1.4.1| | 2 |
Wheel alignment incorrect which adversely affects the handling |2.5.1| | 2 |
Headlamp at least one does not illuminate on main beam |1.2.2a|ii|| | 2 |
Parking brake efficiency below requirements |1.4.2 |a| |i|| | 2 |
Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 2 |
Rear brake disc in such a condition that it is seriously weakened | 2 |
Front position lamp|s| incorrect colour |1.1.A.3e| | 2 |
Side repeater missing |1.4.A.2b| | 2 |
Riders seat insecure |6.2.1a| | 2 |
Nearside Rear Anti-roll bar linkage pin or bush excessively worn |5.3.4 |a| |i|| | 2 |
Offside Rear Anti-roll bar linkage pin or bush excessively worn |5.3.4 |a| |i|| | 2 |
Front Motorcycle structure excessively damaged front wheel is out of alignment with rear wheel |6.1.1a| | 2 |
Rear shock absorber seal failed and leaking oil Both |2.4.A.1c| | 2 |
Indicator switch insecure |1.5.4| | 2 |
Throttle operating incorrectly loose /turns on handlebars |6.2.1f| | 2 |
Stop lamp remains on when the brake is released |1.3.1e| | 2 |
Front brake disc in such a condition that it is seriously weakened | 2 |
Stop lamp not working |4.3.1 |a| |ii|| | 2 |
Rear Position lamp not working |4.2.1 |a|| | 2 |
Front Headlamp at least one does not illuminate on main beam |1.2.2a|ii|| | 2 |
Direction indicators not working |1.5.1c| | 2 |
Drive chain excessively tight |6.2.1d| | 2 |
Rear Drive chain excessively loose |6.2.1d| | 2 |
Front Wheel alignment incorrect which adversely affects the handling |2.5.1| | 2 |
Rear Roller brake test indicates a binding brake |3.3.A1a| | 2 |
Rear Stop lamp remains on when the brake is released |1.3.1e| | 2 |
Front Motorcycle structure excessively damaged |6.1.1a| | 2 |
Exhaust is leaking and excessively noisey |7.1.1b| | 2 |
Roller brake test The less effective brake control does not achieve an efficiency of 25% |1.2.2 |a| |i|| | 2 |
Front Stop lamp not working |4.3.1 |a| |ii|| | 2 |
Rear Drive chain sprocket worn to excess |6.2.1e| | 2 |
Headlamp not working on main beam (4.1.1 (a) (ii)) | 2 |
Headlamp aim not tested (4.1.2 (b)) | 2 |
Throttle operating incorrectly (6.2.7 (a) (i)) | 2 |
Front Brake indicates excessive fluctuation of brake effort (1.2.1 (e)) | 2 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 2 |
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 2 |
Exhaust noise is clearly in excess of that emitted by a similar motorcycle fitted with a standard silencer in average condition (8.1.1 (a)) | 2 |
Rear Valve stem seriously damaged (5.2.3 (j)) | 2 |
Front Brake grabbing severely (1.2.1 (c)) | 2 |
Front Brake excessively binding (1.2.1 (f)) | 2 |
Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 2 |
Front Valve stem seriously damaged (5.2.3 (j)) | 2 |
Stop lamp remains on when the brakes are released | 2 |
Rear Rear reflector missing (4.8.2 (a) (ii)) | 2 |
Horn not working (7.7 (a)) | 2 |
Nearside Side repeater missing |1.4.A.2b| | 1 |
Offside Side repeater missing |1.4.A.2b| | 1 |
Rear fog lamp tell tale missing |1.3.1b| | 1 |
Offside Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Side repeater has less than 50% of the light sources illuminating |1.4.A.2c| | 1 |
Nearside Side repeater excessively deteriorated so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
Offside Steering control has Insufficient clearance at full lock affecting the riders grasp of handlebars |2.1.2b| | 1 |
Wheel alignment incorrect which adversely affects the steering |2.5.1| | 1 |
Rear Roller brake test indicates excessive fluctuation of brake effort |3.3.A1d| | 1 |
Supplementary Restraint System warning lamp indicates a fault |5.4.2| | 1 |
Brake performance not tested |1.2.1 |g|| | 1 |
Nearside Front Suspension arm pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
Offside Front Suspension arm pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
Brake hose excessively deteriorated | 1 |
Rear fog lamp emits a light other than red |1.3.2e| | 1 |
Rear Roller brake test indicates a sticking brake |3.3.A1a| | 1 |
Parking brake: efficiency below requirements |3.7.B.7| | 1 |
Rear Braking system leaking |3.6.A.1| | 1 |
Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
Exhaust emissions likely to be affected by an induction leak |8.2.1.1 |b|| | 1 |
Windscreen has damage | 1 |
Nearside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Front Motorcycle structure excessively distorted Front wheel out of alignment with rear wheel |6.1.1a| | 1 |
Headlamp aim beam image kick up to the offside |1.6| | 1 |
Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 1 |
Parking brake lever has no reserve travel |3.1.6b| | 1 |
Offside Rear wheel spindle securing nut locking device insecure |2.4.A.2b| | 1 |
Front Front wheel bearings have excessive free play |2.3.5b| | 1 |
Drive chain sprocket worn to excess |6.2.1e| | 1 |
Nearside Front Direction indicators not working |1.5.1c| | 1 |
Front Throttle has a significant change in engine speed whilst moving the steering from lock to lock |2.1.4| | 1 |
Rear Axle beam has excessive vertical movement between stub axle and axle beam |2.5.A.1a| | 1 |
Horn not working |1.6.2a| | 1 |
Stop lamp not working |1.2.1b| | 1 |
Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Front Brake disc contaminated |1.1.14 |b|| | 1 |
Front Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 1 |
Nearside Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 1 |
All position lamps do not illuminate immediately when switched on |1.1.3a| | 1 |
Stop lamp remains on when the brake is released when rear brake applied light stays on. |1.3.1e| | 1 |
Steering movement excessively stiff with the weight on the lower bearing |2.2.1a| | 1 |
Rear Brake component has restricted free movement and operation is likely to be impeded |3.2.A1h| | 1 |
Offside Front Direction indicator not working |1.5.1c| | 1 |
Front Motorcycle structure insecure and likely to affect the correct functioning of the steering or braking |6.1.1c| | 1 |
Rear wheel rotation likely to be impeded |6.2.1b| | 1 |
Offside Wheel alignment incorrect which adversely affects the steering |2.5.1| | 1 |
Rear Brake back plate|s| securing bolt|s| missing |3.2.A1j| | 1 |
Nearside Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Nearside Front Shock absorber has a serious fluid leak |5.3.2 |b|| | 1 |
Offside Front Headlamp incorrect colour |4.1.4 |a|| | 1 |
Nearside Front Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Rear Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 1 |
Nearside Rear Rear shock absorber seal failed and leaking oil |2.4.A.1c| | 1 |
Offside Rear Rear shock absorber seal failed and leaking oil |2.4.A.1c| | 1 |
Offside Rear Brake performance not tested |3.3| | 1 |
Plate brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.B2b| | 1 |
Rear Stop lamp remains on when the brake is released control |1.3.1e| | 1 |
Rear wheel spindle securing nut locking device insecure |2.4.A.2b| | 1 |
Offside Rear shock absorber insecurely mounted |2.4.A.3b| | 1 |
Front Brake lever has inadequate reserve travel |3.1.3b| | 1 |
Roller brake test No brake control achieves an efficiency of 30%. |3.3.A2a| | 1 |
Front Fairings so located that it is likely to impede the steering |2.1.2e| | 1 |
Floor brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.C1b| | 1 |
Rear wheel spindle securing nut|s| loose |2.4.A.2b| | 1 |
Rear position lamp incorrect colour |1.1.2b| | 1 |
Steering headbearing has excessive wear or free play |2.2.2 |f| |i|| | 1 |
Front Brake fluid reservoir fluid level dangerously low |3.2.B1d| | 1 |
Front Front suspension has excessive stiffness in the suspension movement. |2.3.6b| | 1 |
Rear Brake disc|s| excessively scored |3.2.A1l| | 1 |
Stop lamp does not illuminate immediately a brake applies both brakes |1.3.1a| | 1 |
Offside Front Brake indicates excessive fluctuation of brake effort |1.2.1 |e|| | 1 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
Rear fog lamp not working |1.3.2b| | 1 |
Front Valve stem seriously damaged |5.2.3 |j|| | 1 |
Front Brake lever is so short and the brake cannot be readily applied |3.1.3c| | 1 |
Rear Stop lamp does not illuminate immediately a brake applies switch |1.3.1a| | 1 |
Front Steering movement excessively `notchy` with the weight on the lower bearing |2.2.1a| | 1 |
Front Exhaust is leaking and excessively noisey |7.1.1b| | 1 |
Rear Brake disc|s| is excessively distorted |3.2.A1m| | 1 |
Dipswitch does not deflect the main beam/s, making them into dipped beam/s |1.2.2b|ii|| | 1 |
Exhaust emissions likely to be affected by an exhaust leak |8.2.1.1 |b|| | 1 |
Exhaust Lambda reading after 2nd fast idle outside specified limits |8.2.1.2 |c|| | 1 |
Undertray likely to become detached |6.2.1 |a| |ii|| | 1 |
Exhaust system not adequately supported |7.1.1| | 1 |
Front Floor brake test indicates a binding brake |3.3.C2c| | 1 |
Rear Brake lever has insufficient reserve travel |1.1.2 |a|| | 1 |
Steering headbearing excessively stiff or notchy |2.2.2 |f| |i|| | 1 |
Front Brake master cylinder fluid level dangerously low |3.2.B1d| | 1 |
Rear shock absorber seal failed and leaking oil |2.4.A.1c| | 1 |
Exhaust mounting does not fully support the exhaust system |7.1.1.c| | 1 |
Offside Rear Direction indicator insecure |1.4.A.2b| | 1 |
Locking device|s| not correctly fitted which may make the motor bicycle dangerous to ride chain adjusters |6.2.1h| | 1 |
Rear Wheel bearing has excessive play |5.1.3 |a| |i|| | 1 |
Stop lamp not working From front brake lever |4.3.1 |a| |ii|| | 1 |
Throttle operating incorrectly revs to fast on idle |6.2.1f| | 1 |
Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Headlamp aim not tested |4.1.2 |b|| | 1 |
Brake lever has insufficient reserve travel |1.1.2 |a|| | 1 |
Stop lamp switch with a delay in operation |4.3.2 |a| |ii|| | 1 |
Rear Roller brake test indicates brake effort fall disproportional to brake lever or pedal effort |3.3.A1c| | 1 |
Nearside Brake lever attachment screws loose |3.1.2b| | 1 |
Headlamp insecure |1.2.3b| | 1 |
Front Front wheel insecure |4.2.3b| | 1 |
Vehicle Identification Number not permanently displayed |6.3.5.a| | 1 |
Nearside Front Obligatory mirror missing |8.1.1| | 1 |
Offside Rear Rear reflector missing |1.5.1a| | 1 |
Front Front position lamp does not illuminate immediately when switched on |1.1.3a| | 1 |
Rear Rear position lamp adversely affected by the operation of another lamp |1.1.3b| | 1 |
Nearside Front Front position lamp does not illuminate immediately when switched on |1.1.3a| | 1 |
Offside Front Front position lamp does not illuminate immediately when switched on |1.1.3a| | 1 |
Front Steering headbearing has excessive free play |2.2.2| | 1 |
Rear All position lamps do not illuminate immediately when switched on |1.1.3a| | 1 |
Offside Rear Exhaust excessively deteriorated |7.1.1a| | 1 |
Offside Rear Exhaust is leaking and excessively noisey |7.1.1b| | 1 |
Offside Rear Upper Direction indicator not working |1.5.1c| | 1 |
Front Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Handlebar deformed |2.1.1b| | 1 |
Exhaust noise is clearly in excess of that emitted by a similar motorcycle fitted with a standard silencer in average condition |8.1.1 |a|| | 1 |
Nearside Direction indicator not working |1.5.1c| | 1 |
Brake lever cannot be applied smoothly |3.1.3d| | 1 |
Rear Brake lever is damaged and the brake cannot be readily applied |3.1.3c| | 1 |
Nearside Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 1 |
Exhaust excessively deteriorated |7.1.1a| | 1 |
Offside Front Wheel bearing play so excessive it is likely to break up |5.1.3 |a| |ii|| | 1 |
Offside Front Shock absorber has a serious fluid leak |5.3.2 |b|| | 1 |
Steering lock stop maladjusted |2.1.3| | 1 |
Nearside Front Brake disc|s| has excessive run out |3.2.A1m| | 1 |
Front Floor brake test indicates a severely juddering brake |3.3C2d.| | 1 |
Front Brake fluid reservoir severely corroded inspection glass |3.2.B1b| | 1 |
Rear reflector missing |1.5.1a| | 1 |
Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Rear Brake lever pivot has excessive free play (1.1.1 (b)) | 1 |
Headlamp insecure (4.1.1 (c)) | 1 |
Front Shock absorber has negligible damping effect (5.3.2 (b)) | 1 |
Front Stop lamp not working brake switch (4.3.1 (a) (ii)) | 1 |
Front Horn not working (7.7 (a) (ii)) | 1 |
Drive chain horseshoe locking device incorrectly fitted (6.1.7 (j) (i)) | 1 |
Handlebar fouling on the fuel tank or bodywork on full lock (2.1.4 (b)) | 1 |
Steering headbearing excessively stiff or notchy (2.2.2 (f) (i)) | 1 |
Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Windscreen washer not working | 1 |
Drive chain excessively tight (6.1.7 (k) (i)) | 1 |
Front Position lamp not working (4.2.1 (a)) | 1 |
Horn not working (7.7 (a) (ii)) | 1 |
Offside Front Upper Brake hose excessively twisted hose fowling fairing on full right lock resulting in dangerous folding of brakeline at master cylinder (1.1.12 (b) (ii)) | 1 |
Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
Rear Position lamp not working (4.2.1 (a)) | 1 |
Wheel alignment incorrect which adversely affects the handling (2.4 (a)) | 1 |
Drive chain excessively loose (6.1.7 (c) (i)) | 1 |
Throttle control functioning such that safe operation of the motorcycle is adversely affected (6.2.7 (a) (ii)) | 1 |
Rear Brake indicates excessive fluctuation of brake effort (1.2.1 (e)) | 1 |
Rear Brake excessively binding (1.2.1 (f)) | 1 |
Front Brake fluid significantly below minimum mark (1.1.10 (d) (ii)) | 1 |
Front Brake fluid not visible (1.1.10 (d) (iii)) | 1 |
Floor brake test The less effective brake control does not achieve an efficiency of 25% (1.2.2 (a) (i)) | 1 |
Rear All position lamps not working (4.2.1 (a)) | 1 |
Stop lamp not working (4.3.1 (a) (ii)) | 1 |
Nearside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
Brakes imbalanced across an axle | 1 |
Handlebar grip insecure to handlebar Right hand grip not stuck to throttle tube (2.2.1 (d) (ii)) | 1 |
Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
Rear Stop lamp does not illuminate by the operation of both brake controls (4.3.2 (a) (iii)) | 1 |
Rear Stop lamp not working (4.3.1 (a) (ii)) | 1 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 1 |
Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Nearside Front Macpherson strut top bush or bearing has excessive wear or free play (5.3.4 (a) (i)) | 1 |
Offside Front Macpherson strut top bush or bearing has excessive wear or free play (5.3.4 (a) (i)) | 1 |
Nearside Front Service brake excessively binding (1.2.1 (f)) | 1 |
Offside Service brake excessively binding (1.2.1 (f)) | 1 |
Offside Front Stop lamp does not illuminate by the operation of both brake controls (4.3.2 (a) (iii)) | 1 |
Nearside Front Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Front Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
Nearside Front Engine mounting damaged or deteriorated resulting in excessive movement (6.1.8 (a) (i)) | 1 |
Offside Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
Rear Lower Floor excessively deteriorated Inner valence (6.2.4 (a) (i)) | 1 |
Rear Upper Direction indicator obviously incorrectly positioned (4.4.3 (a)) | 1 |
Headlamp has a product on the lens so that the light output is severely reduced both (4.1.4 (b)) | 1 |
Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
Drive chain worn to excess (6.1.7 (c) (i)) | 1 |
Rear Shock absorber has negligible damping effect (5.3.2 (b)) | 1 |
Power steering component leaking rack (2.1.5 (a)) | 1 |
Front Exhaust has a major leak of exhaust gases and plate loose (6.1.2 (a)) | 1 |
Front Track rod end ball joint has excessive play both (2.1.3 (b) (i)) | 1 |
Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
Headlamp aim so that beam "kick up" is not visible on the screen (4.1.2 (a)) | 1 |
Steering headbearing has excessive wear or free play (2.2.2 (f) (i)) | 1 |
Position lamp adversely affected by the operation of another lamp headlamp dip beam (4.2.3 (b)) | 1 |
Headlamp not working on dipped beam flickering on and off (4.1.1 (a) (ii)) | 1 |
Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Rear Wheel spindle loose (5.2.1 (c) (i)) | 1 |
Drive chain so worn it is likely to fail (6.1.7 (c) (ii)) | 1 |
Drive chain sprocket worn to excess (6.1.7 (c) (i)) | 1 |
All direction indicators not working (4.4.1 (a) (ii)) | 1 |
Rear Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |