| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 232 |
| Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 170 |
| Registration plate lamp issues | 152 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 126 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 119 |
| Headlamp aim out of alignment | 103 |
| Nearside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 70 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 61 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 51 |
| Windscreen washer not working | 43 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 36 |
| Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 36 |
| Brakes imbalanced across an axle | 34 |
| Offside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 31 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 30 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 29 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 29 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 29 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 28 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 27 |
| Brake hose excessively deteriorated | 26 |
| Registration plate issues | 25 |
| Anti-lock braking system warning lamp indicates an ABS fault | 24 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 23 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 23 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 22 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 22 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 21 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 21 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 21 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 21 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 20 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 17 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 17 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 16 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 16 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 16 |
| Nearside Front Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 14 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 14 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 14 |
| Nearside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 14 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 13 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 13 |
| Offside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 13 |
| Nearside Rear Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 12 |
| Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 12 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 12 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 12 |
| Emissions unable to be completed (8.2.1.2 (d)) | 12 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 12 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 11 |
| Offside Rear Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 11 |
| Parking brake lever has no reserve travel |3.1.6b| | 11 |
| Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 11 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 11 |
| Offside Front Lower Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 11 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 11 |
| Nearside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 10 |
| Rear brake disc in such a condition that it is seriously weakened | 10 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 10 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 10 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 10 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 10 |
| Brake lever has insufficient reserve travel (1.1.2 (a)) | 9 |
| Nearside Front Lower Suspension arm pin or bush excessively worn front bush (5.3.4 (a) (i)) | 9 |
| Nearside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 9 |
| Nearside Front Suspension arm pin or bush excessively worn front bush (5.3.4 (a) (i)) | 9 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 9 |
| Emissions not tested (8.2.1.2 (d)) | 9 |
| Nearside Rear Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 8 |
| Offside Rear Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 8 |
| Offside Front Road wheel fixing missing (5.2.1 (a) (i)) | 8 |
| Offside Front Suspension arm pin or bush excessively worn front bush (5.3.4 (a) (i)) | 8 |
| Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 8 |
| Offside Rear Stop lamp not working |1.2.1b| | 8 |
| Offside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 8 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 8 |
| Offside Stop lamp not working |1.2.1b| | 8 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 8 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 7 |
| Offside Front Lower Suspension arm pin or bush excessively worn front bush (5.3.4 (a) (i)) | 7 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 7 |
| Offside Rear Anti-roll bar linkage fractured (5.3.3 (b) (ii)) | 7 |
| Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 7 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 7 |
| Offside Front Shock absorbers has a serious fluid leak | 7 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 7 |
| Front brake disc in such a condition that it is seriously weakened | 7 |
| Offside Rear Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 7 |
| Central Stop lamp(s) not working (4.3.1 (a) (ii)) | 7 |
| Nearside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 7 |
| Offside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 7 |
| Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 7 |
| Nearside Rear Stop lamp not working |1.2.1b| | 7 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 6 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 6 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 6 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 6 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 6 |
| Nearside Front Shock absorbers has a serious fluid leak | 6 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 6 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 6 |
| Brake pedal anti-slip provision missing (1.1.2 (c)) | 6 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 6 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 6 |
| Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 6 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 5 |
| Offside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 5 |
| Nearside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 5 |
| Nearside Rear Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 5 |
| Offside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 5 |
| Front Position lamp not working (4.2.1 (a) (ii)) | 5 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 5 |
| Nearside Rear Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 5 |
| Nearside Side repeater not working (4.4.1 (a) (ii)) | 5 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 5 |
| Nearside Rear Anti-roll bar linkage fractured (5.3.3 (b) (ii)) | 5 |
| Offside Rear Direction indicator incorrect colour (4.4.3 (a)) | 5 |
| Nearside Front Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 5 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 5 |
| Rear brake binding | 5 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 5 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 5 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 5 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 5 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 5 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 5 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 5 |
| Nearside Front Position lamp not working |4.2.1 |a|| | 5 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 5 |
| Offside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 5 |