| Most common failures | No# failures |
|---|
| Parking brake: efficiency below requirements |3.7.B.7| | 11 |
| Rear parking brake recording little or no effort | 9 |
| Rear brake binding | 9 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Windscreen wiper does not clear the windscreen effectively | 5 |
| Brakes imbalanced across an axle | 4 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 4 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Parking brake lever has no reserve travel |3.1.6b| | 4 |
| Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 3 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 3 |
| Headlamp aim out of alignment | 3 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 3 |
| Offside front brake binding |3.7.B.1| | 3 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Nearside Side repeater not working |1.4.A.2c| | 2 |
| Registration plate lamp issues | 2 |
| Nearside Headlamp not working on main beam |1.7.5a| | 2 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside front brake binding |3.7.B.1| | 2 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 2 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 2 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 2 |
| Registration plate issues | 2 |
| Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 2 |
| Nearside Front Lower Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 2 |
| Parking brake: efficiency below requirements |3.7.C.1b| | 2 |
| Offside Front front brake binding |3.7.B.1| | 2 |
| Nearside Rear Braking system leaking |3.6.A.1| | 2 |
| Exhaust engine idle speed too high |7.3.A.2a| | 2 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 2 |
| Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Headlamp not working on main beam |1.7.5a| | 1 |
| Brake pipe excessively corroded | 1 |
| Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Mechanical brake component has restricted free movement | 1 |
| Offside Front Lower Front suspension locking device missing |2.5.A.4| | 1 |
| Nearside Front Lower Front suspension locking device missing |2.5.A.4| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Front Headlamp not working on main beam |1.7.5a| | 1 |
| Offside Front Headlamp not working on main beam |1.7.5a| | 1 |
| Nearside Rear Vehicle structure has damage which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Direction indicator not working |1.4.A.2c| | 1 |
| Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition |7.1.4| | 1 |
| Nearside Rear Wheel nut|s| loose |4.2.A.1e| | 1 |
| Offside Inner Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Front Steering system has excessive free play detected at the steering wheel |steering rack fitted| |2.2.A.1b| | 1 |
| Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Offside Rear Hydraulic brake cylinder leaking and braking performance affected (1.1.16 (b) (ii)) | 1 |
| Nearside Front front brake binding |3.7.B.1| | 1 |
| Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Windscreen wiper blade missing |8.2.2| | 1 |
| Offside Windscreen wiper blade missing |8.2.2| | 1 |
| Horn not working |1.6.2a| | 1 |
| Offside Rear fog lamp not working |1.3.2b| | 1 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Nearside Rear Stop lamp not working |1.2.1b| | 1 |
| Rear brake application uneven | 1 |
| Service brake: efficiency below requirements |3.7.C.1a| | 1 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Nearside Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Nearside Front brake disc has restricted free movement |3.5.1j| | 1 |
| Offside Front Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt New clip required? |6.1.7 |g| |ii|| | 1 |
| Nearside Front Service brake excessively binding |1.2.1 |f|| | 1 |
| Nearside Rear Service brake excessively binding |1.2.1 |f|| | 1 |
| Offside Obligatory mirror insecure |8.1.1| | 1 |
| Nearside Front Upper Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Front Upper Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Offside Inner Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
| Nearside Front Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Front Side repeater not working |1.4.A.2c| | 1 |
| Offside Outer Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| An item not tested |Manual| | 1 |
| Nearside Rear Obligatory mirror does not provide a view to the rear |8.1.2b| | 1 |
| Offside Front Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Nearside Front Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Offside Front Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Offside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Offside Rear Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Bonnet cannot be secured in the closed position |8.4.1| | 1 |
| Exhaust emits visible black smoke at idle |7.3.A.2b| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Brake pedal anti-slip provision incomplete |3.3.A.1b| | 1 |
| Offside Stop lamp not working |1.2.1b| | 1 |
| Offside Steering rack gaiter split |2.2.D.2d| | 1 |
| Offside Front Front position lamp|s| not in good working order |function impaired| |1.1.4a| | 1 |
| Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Offside Rear Direction indicator not working |1.4.A.2c| | 1 |
| Nearside Rear Brake lever has restricted free movement |3.5.1k| | 1 |
| Offside Rear Brake lever has restricted free movement |3.5.1k| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Front Sub-frame corroded and seriously weakened |2.4.G.1| | 1 |
| Nearside Front Sub-frame inappropriately repaired |2.4.A.2| | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Offside Rear Stop lamp not working |1.2.1b| | 1 |
| Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Brake pedal spongy |3.3.B.1b| | 1 |
| Brake pedal has insufficient reserve movement |3.3.A.5| | 1 |
| Brake pedal creeps down while the pedal is held under pressure |3.3.B.1a| | 1 |
| Battery insecure |1.9.1| | 1 |
| Offside Rear Braking system leaking |3.6.A.1| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Upper Suspension component mounting prescribed area is excessively corroded x2 |2.4.A.3| | 1 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Service brake: efficiency below requirements |3.7.B.7| | 1 |
| Offside Obligatory mirror missing |8.1.1| | 1 |
| Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Exhaust emits clearly visible black smoke during acceleration |7.3.A.2c| | 1 |
| Rear Headlamp not in good working order |not working| |1.2.4a| | 1 |
| Nearside Front Front drive shaft coupling flexible rubber or fabric coupling unit breaking up |2.5.C.1d| | 1 |
| Offside Front Front drive shaft coupling flexible rubber or fabric coupling unit breaking up |2.5.C.1d| | 1 |
| Inner Front Tie bar/rod rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Outer Front Tie bar/rod rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |