Most common failures | No# failures |
---|
Headlamp aim out of alignment | 25 |
Riders seat insecure |6.2.1a| | 8 |
Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 8 |
Roller brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.A2b| | 7 |
Steering headbearing has excessive free play |2.2.2| | 7 |
Rear Brake lever has inadequate reserve travel |3.1.3b| | 7 |
Front Brake lever has inadequate reserve travel |3.1.3b| | 7 |
Front position lamp does not illuminate immediately when switched on |1.1.3a| | 6 |
Offside Rear shock absorber seal failed and leaking oil |2.4.A.1c| | 6 |
Rear Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 5 |
Horn not working |1.7.3a| | 5 |
Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 5 |
Rear Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 5 |
Nearside Rear shock absorber seal failed and leaking oil |2.4.A.1c| | 5 |
Rear Roller brake test indicates a binding brake |3.3.A1a| | 4 |
Front Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 4 |
Front Stop lamp remains on when the brake is released |1.3.1e| | 4 |
Horn not loud enough to be heard by another road user |1.7.3a| | 4 |
Front Horn not working |1.7.3a| | 3 |
Registration plate issues | 3 |
Front wheel bearings have excessive free play |2.3.5b| | 3 |
Front Roller brake test indicates a binding brake |3.3.A1a| | 3 |
Rear Roller brake test indicates a sticking brake |3.3.A1a| | 3 |
Direction indicators affected by the operation of another lamp |1.5.1c| | 3 |
Nearside Handlebar handgrip not secure to handlebars. |2.1.1c| | 3 |
Nearside Front Direction indicator not working |1.5.1c| | 3 |
Direction indicators flashing less than 60 times a minute |1.5.1c| | 3 |
Rear Stop lamp remains on when the brake is released |1.3.1e| | 3 |
Roller brake test No brake control achieves an efficiency of 30%. |3.3.A2a| | 3 |
Front Direction indicators not working |1.5.1c| | 2 |
Rear Direction indicators not working |1.5.1c| | 2 |
Nearside Rear Direction indicator not working |1.5.1c| | 2 |
Throttle operating incorrectly |6.2.1f| | 2 |
Rear Motorcycle structure insecure and likely to affect the correct functioning of the steering or braking |6.1.1c| | 2 |
Exhaust is leaking and excessively noisey |7.1.1b| | 2 |
Front suspension assembly excessive wear or free play in a front suspension component |2.3.4| | 2 |
Rear shock absorber seal failed and leaking oil |2.4.A.1c| | 2 |
Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 2 |
Front wheel bearings are excessively rough |2.3.5b| | 2 |
Headlamp at least one does not illuminate on main beam |1.2.2a|ii|| | 2 |
Front Front suspension assembly excessive wear or free play in a front suspension component |2.3.4| | 2 |
Front Roller brake test indicates a sticking brake |3.3.A1a| | 2 |
Riders seat insecure (6.2.5 (a) (ii)) | 2 |
Brake lever has inadequate reserve travel |3.1.3b| | 2 |
All position lamps do not illuminate immediately when switched on |1.1.3a| | 2 |
Direction indicators not working |1.5.1c| | 2 |
Rear Roller brake test indicates a severely grabbing brake |3.3.A1b| | 2 |
Roller brake test Neither brake control achieves an efficiency of 25% |3.3.A2b| | 2 |
Rear Brake lining|s| less than 1.5 mm thick |3.2.A1f|i|| | 2 |
Handlebar mounting clamp loose |2.1.1a| | 2 |
Offside Rear Direction indicator not working |4.4.1 |a| |ii|| | 1 |
Chain guard insecure |6.2.1c| | 1 |
Rear wheel spindle securing nut|s| loose |2.4.A.2b| | 1 |
Rear Wheel spoke excessively loose |4.2.1b| | 1 |
Central Rear Wheel spoke missing |5.2.2 |d|| | 1 |
Centre Rear Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 1 |
Front Horn not working (7.7 (a) (ii)) | 1 |
Rear Brake lever cannot be released smoothly |3.1.3d| | 1 |
Front Direction indicator not working |1.5.1c| | 1 |
Rear Wheel damaged significantly reducing the original strength |4.2.1a| | 1 |
Roller brake test indicates a sticking brake |3.3.A1a| | 1 |
Rear position lamp damaged and function impaired |1.1.1b| | 1 |
Nearside Rear Direction indicators not working |1.5.1c| | 1 |
Offside Direction indicators affected by the operation of another lamp |1.5.1c| | 1 |
Front Front mudguard can easily contact any fixed point of the motor bicycle. |2.3.7| | 1 |
Handlebar mounting clamp bolt loose |2.1.1a| | 1 |
Front Handlebar mounting clamp loose |2.1.1a| | 1 |
Headlamp insecure |1.2.3b| | 1 |
Nearside Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 1 |
Offside Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 1 |
Rear Rear wheel bearings are excessively rough |2.4.A.2c| | 1 |
Exhaust excessively deteriorated |7.1.1a| | 1 |
Front Roller brake test indicates a severely grabbing brake |3.3.A1b| | 1 |
Stop lamp affected by the operation of the horn |1.3.2| | 1 |
Lower Steering headbearing has excessive free play |2.2.2| | 1 |
Front Handlebar mounting clamp bolt loose |2.1.1a| | 1 |
Front Steering movement excessively stiff with the weight on the lower bearing |2.2.1a| | 1 |
Fuel hose leaking |7.2.1a| | 1 |
Nearside Direction indicators flashing less than 60 times a minute |1.5.1c| | 1 |
Nearside Indicator switch insecure |1.5.4| | 1 |
Offside Steering control handlebar movement restricted by trapped cables |2.1.2c| | 1 |
Nearside Brake lever cannot be released smoothly |3.1.3d| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill panel |5.3.6 |a| |i|| | 1 |
Nearside Front Outer Direction indicator not working |4.4.1 |a| |ii|| | 1 |
Offside Rear Rear fog lamp missing |1.3.2a| | 1 |
Nearside Rear Stop lamp not working |1.2.1b| | 1 |
Nearside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front front brake binding |3.7.B.1| | 1 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 1 |
Brakes imbalanced across an axle | 1 |
Offside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
rear parking |secondary| brakes imbalanced | 1 |
Rear parking brake recording little or no effort | 1 |
Steering system has a road wheel fouling a part of the vehicle Both front |2.2.D.2a| | 1 |
Rear Rear wheel bearings have excessive free play |2.4.A.2c| | 1 |
Front Upper Handlebar mounting clamp loose |2.1.1a| | 1 |
Nearside Front Brake lever is so short and the brake cannot be readily applied |3.1.3c| | 1 |
Brake lever excessively damaged |3.2.A1c| | 1 |
Rear Floor brake test indicates a sticking brake |3.3.C2c| | 1 |
Offside Front Direction indicator not working |1.5.1c| | 1 |
Offside Rear Direction indicator not working |1.5.1c| | 1 |
Indicator tell tale not functioning |1.5.2| | 1 |
Nearside Rear Direction indicator flashing less than 60 times a minute |1.5.1c| | 1 |
All direction indicators not working when running (4.4.1 (a) (ii)) | 1 |
Handlebar retaining device loose (2.2.1 (b) (i)) | 1 |
Brake excessively binding FRONT (1.2.1 (f)) | 1 |
Nearside Direction indicator not working |1.5.1c| | 1 |
Offside Direction indicator flashing more than 120 times per minute |1.5.1c| | 1 |
Steering movement excessively stiff with the weight on the lower bearing |2.2.1a| | 1 |
Front Front suspension has inadequate damping effect. |2.3.6c| | 1 |
Exhaust mounting does not fully support the exhaust system |7.1.1.c| | 1 |
Front wheel spindle loose |2.3.3a| | 1 |
Front Brake excessively binding (1.2.1 (f)) | 1 |
Rear Wheel spoke cracked. |4.2.1b| | 1 |
Direction indicator flashing less than 60 times a minute |1.5.1c| | 1 |
Front Horn not loud enough to be heard by another road user |1.7.3a| | 1 |
Offside Brake lever has inadequate reserve travel |3.1.3b| | 1 |
Front mudguard insecure |2.3.7| | 1 |
Offside Brake lever is positioned so that the brake cannot be readily applied |3.1.3c| | 1 |
Nearside Front Handlebar handgrip not secure to handlebars. |2.1.1c| | 1 |
Front Front position lamp does not illuminate immediately when switched on |1.1.3a| | 1 |
All direction indicators not working (4.4.1 (a) (ii)) | 1 |
Steering headbearing excessively stiff or notchy (2.2.2 (f) (i)) | 1 |
Rear Wheel spoke excessively bent (5.2.2 (d)) | 1 |
All position lamps adversely affected by the operation of another lamp |1.1.3b| | 1 |
All position lamps adversely affected by the operation of the horn |1.1.3b| | 1 |
Nearside Direction indicator flashing less than 60 times a minute |1.5.1c| | 1 |
Offside Direction indicator flashing less than 60 times a minute |1.5.1c| | 1 |
Nearside Lower Front suspension assembly excessive wear or free play in a front suspension component |2.3.4| | 1 |
Offside Lower Front suspension assembly excessive wear or free play in a front suspension component |2.3.4| | 1 |
Rear Roller brake test indicates excessive fluctuation of brake effort |3.3.A1d| | 1 |
Rear wheel bearings have excessive free play |2.4.A.2c| | 1 |
Rear Roller brake test indicates brake effort rise disproportional to brake lever or pedal effort |3.3.A1c| | 1 |
Front Brake lever is inoperative |3.1.3c| | 1 |
Rear Stop lamp insecure |1.3.3b| | 1 |
Brake performance not tested |3.3| | 1 |
Offside Front Brake lever has insufficient reserve travel (1.1.2 (a)) | 1 |
Front Position lamp not working (4.2.1 (a)) | 1 |
Throttle operating incorrectly Engine Revs Excessive on idle |6.2.1f| | 1 |
Nearside Brake lever has inadequate reserve travel |3.1.3b| | 1 |
Footrest insecure |6.2.1a| | 1 |
Stop lamp affected by the operation of another lamp |1.3.2| | 1 |
Horn is not continous or uniform |1.7.3c| | 1 |
Front Floor brake test indicates a severely grabbing brake |3.3.C2d| | 1 |
Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 1 |
Front Front wheel bearings have excessive free play |2.3.5b| | 1 |
Front Brake cable knotted |3.2.A1b| | 1 |
Front Brake lining|s| less than 1.5 mm thick |3.2.A1f|i|| | 1 |
Front mudguard can easily contact any fixed point of the motor bicycle. |2.3.7| | 1 |
Nearside Rear Rear shock absorber seal failed and leaking oil |2.4.A.1c| | 1 |
Front Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 1 |
Front Steering headbearing has excessive free play |2.2.2| | 1 |
Nearside Rear Brake lever has inadequate reserve travel |3.1.3b| | 1 |
Leg shield insecure and likely to impede the steering |2.1.2e| | 1 |
Fairings insecure and likely to impede the steering front fender |2.1.2e| | 1 |
Rear position lamp adversely affected by the operation of another lamp |1.1.3b| | 1 |
Rear Wheel spoke excessively loose (5.2.2 (d)) | 1 |
Centre Exhaust excessively deteriorated |7.1.1a| | 1 |
Front Headlamp dipped beam flickers when tapped lightly by hand |1.2.2c| | 1 |
Front Headlamp main beam flickers when tapped lightly by hand |1.2.2c| | 1 |
Locking devices not correctly fitted which may make the motor bicycle dangerous to ride |6.2.1h| | 1 |