Most common failures | No# failures |
---|
Headlamp aim out of alignment | 24 |
Roller brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.A2b| | 11 |
Steering headbearing has excessive free play |2.2.2| | 8 |
Front Roller brake test indicates a binding brake |3.3.A1a| | 7 |
Rear Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 6 |
Headlamp at least one does not illuminate on main beam |1.2.2a|ii|| | 6 |
Front Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 6 |
Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 5 |
Front shock absorber seal failed and leaking oil |2.3.3| | 4 |
Throttle operating incorrectly |6.2.1f| | 4 |
Drive chain excessively loose |6.2.1d| | 4 |
Wheel alignment incorrect which adversely affects the handling |2.5.1| | 4 |
Front position lamp does not illuminate immediately when switched on |1.1.3a| | 4 |
Front Front position lamp does not illuminate immediately when switched on |1.1.3a| | 3 |
Rear Drive chain sprocket worn to excess |6.2.1e| | 3 |
Registration plate issues | 3 |
Front Brake lever has inadequate reserve travel |3.1.3b| | 3 |
Steering control has Insufficient clearance at full lock affecting the riders grasp of handlebars |2.1.2b| | 2 |
Front Brake disc|s| excessively worn |3.2.A1l| | 2 |
Steering headbearing has excessive wear or free play (2.2.2 (f) (i)) | 2 |
Nearside Front Brake disc|s| excessively worn |3.2.A1l| | 2 |
Offside Front Brake disc|s| excessively worn |3.2.A1l| | 2 |
Nearside Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 2 |
Offside Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 2 |
Brake lever has inadequate reserve travel |3.1.3b| | 2 |
Rear Roller brake test indicates excessive fluctuation of brake effort |3.3.A1d| | 2 |
Horn not working |1.7.3a| | 2 |
Rear Brake reaction bracket insecure |3.2.A1j| | 2 |
Rear Motorcycle structure excessively corroded |6.1.1a| | 2 |
Rear Drive chain worn to excess |6.2.1e| | 2 |
Rear Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 2 |
Front Floor brake test indicates a binding brake |3.3.C2c| | 2 |
Front Headlamp at least one does not illuminate on main beam |1.2.2a|ii|| | 2 |
Fuel tank leaking |7.2.1a| | 2 |
Drive chain sprocket carrier worn to excess |6.2.1e| | 2 |
Rear Stop lamp remains on when the brake is released |1.3.1e| | 2 |
Front Steering headbearing has excessive free play |2.2.2| | 2 |
Handlebar mounting excessively deteriorated |flexible type| |2.1.1d| | 2 |
Nearside Handlebar handgrip not secure to handlebars. |2.1.1c| | 2 |
Offside Handlebar handgrip not secure to handlebars. |2.1.1c| | 2 |
Exhaust is leaking and excessively noisey |7.1.1b| | 2 |
Front Front wheel bearings have excessive free play |2.3.5b| | 2 |
Rear Roller brake test indicates a sticking brake |3.3.A1a| | 2 |
Front Brake master cylinder leaking hydraulic fluid |3.2.B1e| | 2 |
Steering movement excessively `notchy` with the weight on the lower bearing |2.2.1a| | 2 |
Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 2 |
Steering movement excessively rough with the wheel raised |2.2.1b| | 1 |
Offside Rear Drive chain worn to excess |6.2.1e| | 1 |
Rear wheel bearings have excessive free play |2.4.A.2c| | 1 |
Rear Brake pedal has insufficient reserve travel |1.1.2 |a|| | 1 |
Nearside Front Shock absorber has a serious fluid leak (5.3.2 (b)) | 1 |
Rear Rear suspension has corrosion which reduces the strength of a load bearing member or its supporting structure. |2.4.A.2d| | 1 |
Front Roller brake test indicates a severely juddering brake |3.3.A1b| | 1 |
Front Brake component leaking fluid brake master cyclinder fluid level window |3.2.B4| | 1 |
Front Horn not loud enough to be heard by another road user |1.7.3a| | 1 |
Front Position lamp not working (4.2.1 (a)) | 1 |
Front Steering headbearing has excessive wear or free play (2.2.2 (f) (i)) | 1 |
Steering headbearing has excessive wear or free play |2.2.2 |f| |i|| | 1 |
Front Brake lever cannot be applied smoothly |3.1.3d| | 1 |
Offside Rear Rear shock absorber seal failed and leaking oil |2.4.A.1c| | 1 |
Nearside Rear Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 1 |
Nearside Front Brake component has restricted free movement and operation is likely to be impeded |3.2.A1h| | 1 |
Offside Rear Direction indicator not working |1.5.1c| | 1 |
Headlamp aim not tested |4.1.2 |b|| | 1 |
Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Rear Stop lamp not working (4.3.1 (a) (ii)) | 1 |
Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 1 |
Offside Locking device|s| not correctly fitted which may make the motor bicycle dangerous to ride |6.2.1h| | 1 |
Offside Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 1 |
Nearside Front Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Front Stop lamp remains on when the brake is released |1.3.1e| | 1 |
Offside Steering control has Insufficient clearance at full lock affecting the riders grasp of handlebars |2.1.2b| | 1 |
Front Roller brake test indicates excessive fluctuation of brake effort |3.3.A1d| | 1 |
Exhaust excessively deteriorated |7.1.1a| | 1 |
Offside Rear Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 1 |
Rear reflector missing (4.8.2 (a) (ii)) | 1 |
Front Brake disc|s| has excessive run out |3.2.A1m| | 1 |
Steering control has Insufficient clearance at full lock affecting the riders operation of the controls |2.1.2b| | 1 |
Brake lever attachment screws missing |3.1.2b| | 1 |
Rear suspension component loose |2.4.A.1a| | 1 |
Front suspension has inadequate damping effect. |2.3.6c| | 1 |
Offside Rear Brake pedal attachment screws missing. |3.1.2b| | 1 |
Locking device|s| not correctly fitted which may make the motor bicycle dangerous to ride |6.2.1h| | 1 |
Brake disc|s| excessively worn |3.2.A1l| | 1 |
Footrest insecure |6.2.1a| | 1 |
Offside Lower Rear suspension has corrosion which reduces the strength of a load bearing member or its supporting structure. |2.4.A.2d| | 1 |
Front Stop lamp does not emit a steady light Front Brake lever does not light up rear brake light |1.3.1b| | 1 |
Lower Motorcycle structure excessively corroded |6.1.1a| | 1 |
Nearside Front Sidecar direction indicator not working |1.5.1c| | 1 |
Nearside Rear Sidecar direction indicator flashing more than 120 times per minute |1.5.1c| | 1 |
Front Stop lamp does not illuminate by the operation of both brake controls (4.3.2 (a) (iii)) | 1 |
Front Suspension component modified so the suspension is inoperative (5.3.3 (c) (ii)) | 1 |
Front Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 1 |
Centre Exhaust is leaking and excessively noisey |7.1.1b| | 1 |
Centre Lower Motorcycle structure cracked |6.1.1a| | 1 |
Headlamp aim not tested |1.6| | 1 |
Front position lamp deteriorated and function impaired |1.1.1b| | 1 |
Rear wheel spindle securing nut locking device missing |2.4.A.2b| | 1 |
Front Brake disc|s| friction surface contaminated by oil or grease |3.2.A1k| | 1 |
Front wheel bearings have excessive free play |2.3.5b| | 1 |
Brake performance not tested |3.3| | 1 |
Centre Handlebar handgrip not secure to handlebars. |2.1.1c| | 1 |
Hydraulic brake control creeps under load. |3.1.4a| | 1 |
Stop lamp does not illuminate immediately a brake applies from front |1.3.1a| | 1 |
An item not tested |Manual| | 1 |
Front wheel spindle securing nut locking device missing |2.3.5a| | 1 |
Offside Rear Motorcycle structure excessively corroded |6.1.1a| | 1 |
Rear Drive chain excessively loose |6.2.1d| | 1 |
Plate brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.B2b| | 1 |
Front Gradient brake test indicates a sticking brake |3.3.D1c| | 1 |
Fuel cap does not fasten securely maintaining the sealing arrangement |7.2.2b| | 1 |
Nearside Front Brake cylinder leaking hydraulic fluid |3.2.B1e| | 1 |
Front Brake component has restricted free movement and operation is likely to be impeded |3.2.A1h| | 1 |
Front Brake excessively binding (1.2.1 (f)) | 1 |
Rear Brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
Roller brake test The less effective brake control does not achieve an efficiency of 25% (1.2.2 (a) (i)) | 1 |
Nearside Front Brake disc|s| has excessive run out |3.2.A1m| | 1 |
Front Brake hose leaking fluid |3.2.B4| | 1 |
Offside Front Brake pipe union leaking fluid |3.2.B4| | 1 |
Rear Rear suspension component excessively corroded. |2.4.A.1a| | 1 |
Brake lever is positioned so that the brake cannot be readily applied |3.1.3c| | 1 |
Rear Floor brake test indicates a sticking brake |3.3.C2c| | 1 |
Nearside Front Direction indicators not working |1.5.1c| | 1 |
Brake lever cannot be applied smoothly |3.1.3d| | 1 |
Headlamp insecure |1.2.3b| | 1 |
Steering lock stop ineffective |2.1.3| | 1 |
Front Hydraulic brake control feels spongy |3.1.4a| | 1 |
Rear Brake pedal is bent and the brake cannot be readily applied |3.1.3c| | 1 |
Front Brake pedal is so short and the brake cannot be readily applied |3.1.3c| | 1 |
Nearside Rear shock absorber seal failed and leaking oil |2.4.A.1c| | 1 |
Offside Rear shock absorber seal failed and leaking oil |2.4.A.1c| | 1 |
Rear Brake locking device missing |3.2.A1e| | 1 |
Rear reflector on motorcycle missing |1.4.1| | 1 |
Direction indicator missing |1.5.1a| | 1 |
Offside Rear suspension has corrosion which reduces the strength of a load bearing member or its supporting structure. |2.4.A.2d| | 1 |
Brake hose damaged | 1 |
Brake excessively binding front brakes binding (1.2.1 (f)) | 1 |
Stop lamp not working front brake light switch not working (4.3.1 (a) (ii)) | 1 |
Front Floor brake test indicates a sticking brake |3.3.C2c| | 1 |
Nearside Steering lock stop ineffective |2.1.3| | 1 |
Steering control handlebar movement restricted by taut cables |2.1.2c| | 1 |
Rear Stop lamp deteriorated and function impaired |1.3.3a| | 1 |
Rear Rear shock absorber seal failed and leaking oil |2.4.A.1c| | 1 |
Steering movement excessively stiff with the weight on the lower bearing |2.2.1a| | 1 |
Drive chain fouling another component |6.2.1d| | 1 |
Brake pedal has inadequate reserve travel |3.1.3b| | 1 |
Rear position lamp damaged and function impaired |1.1.1b| | 1 |
Direction indicators flashing more than 120 times per minute |1.5.1c| | 1 |
Nearside Front Footrest insecure |6.2.1a| | 1 |
Centre Rear Roller brake test indicates a binding brake |3.3.A1a| | 1 |
Centre Rear Motorcycle structure excessively corroded |6.1.1a| | 1 |
Brake locking device missing split pin missing from rear brake anchor |3.2.A1e| | 1 |
Front wheel insecure |4.2.3b| | 1 |
Rear suspension has corrosion which reduces the strength of a load bearing member or its supporting structure. |2.4.A.2d| | 1 |
Rear Brake reaction bracket securing bolt|s| missing |3.2.A1j| | 1 |
Rear Roller brake test indicates a binding brake |3.3.A1a| | 1 |
Rear Roller brake test indicates brake effort rise disproportional to brake lever or pedal effort |3.3.A1c| | 1 |
Rear Brake pedal has inadequate reserve travel |3.1.3b| | 1 |
Nearside Rear Locking device|s| not correctly fitted which may make the motor bicycle dangerous to ride |6.2.1h| | 1 |
Horn not working |7.7 |a| |ii|| | 1 |
Offside Front Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Offside Front Footrest insecure |6.2.1a| | 1 |
Nearside Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Offside Front shock absorber seal failed and leaking oil |2.3.3| | 1 |