| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 30 |
| Headlamp aim out of alignment | 10 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 7 |
| Brakes imbalanced across an axle | 7 |
| Registration plate lamp issues | 6 |
| Registration plate issues | 5 |
| Rear brake binding | 5 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 5 |
| Offside front brake binding |3.7.B.1| | 4 |
| Offside Rear fog lamp not working |1.3.2b| | 4 |
| Rear fog lamp not working |1.3.2b| | 4 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 3 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 3 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Stop lamp not working |1.2.1b| | 3 |
| Engine MIL inoperative or indicates a malfunction |8.2.1.2 |h|| | 2 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 2 |
| Service brake: efficiency below requirements |3.7.B.7| | 2 |
| Rear Rear fog lamp not working |1.3.2b| | 2 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 2 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 2 |
| Horn not working |1.6.2a| | 2 |
| Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 2 |
| Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 2 |
| Nearside Rear Service brake excessively binding |1.2.1 |f|| | 1 |
| Rear fog lamp missing |4.5.1 |a| |ii|| | 1 |
| Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Nearside Headlamp aim not tested |1.8.A.1c| | 1 |
| Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Rear fog lamp does not emit a steady red light |4.5.4 |a|| | 1 |
| Brake pipe excessively corroded | 1 |
| Offside Front Body has a sharp edge caused by corrosion door |6.1.C.1| | 1 |
| brake disc in such a condition that it is seriously weakened |3.5.1i| | 1 |
| Parking brake: efficiency below requirements |3.7.B.7| | 1 |
| Nearside Front front brake binding |3.7.B.1| | 1 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded outter sill |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
| Nearside Front Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement stablizer bar bushes |2.4.G.2| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Braking system leaking |3.6.A.1| | 1 |
| Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Obligatory mirror insecure |8.1.1| | 1 |
| Brake fluid contaminated |1.8 |a|| | 1 |
| Offside Front Position lamp not working |4.2.1 |a|| | 1 |
| Service brake efficiency below requirements |1.2.2 |a| |i|| | 1 |
| Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
| Offside Drive shaft which forms part of the suspension coupling gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.4.G.4e| | 1 |
| Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Front brake application uneven | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Rear fog lamp switch faulty |1.3.1a| | 1 |
| Battery insecure |1.9.1| | 1 |
| Nearside Rear wheel bearing has excessive play |2.6.2| | 1 |
| Offside Rear Inner Drive shaft which forms part of the suspension coupling gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.4.G.4e| | 1 |
| Nearside Stop lamp not working |1.2.1b| | 1 |
| Hazard warning switch faulty |1.4.B.1d| | 1 |
| front brakes release unevenly |3.7.B.4| | 1 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Rear Rear fog lamp does not emit a steady red light |4.5.4 |a|| | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Mechanical brake component has restricted free movement | 1 |
| Rear Mechanical brake component has restricted free movement | 1 |
| Rear fog lamp tell tale not working |1.3.1b| | 1 |
| Offside Front Service brake excessively binding |1.2.1 |f|| | 1 |
| Offside Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Offside Rear Position lamp not working |4.2.1 |a|| | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Exhaust emits clearly visible black smoke during acceleration |7.3.A.2c| | 1 |
| Exhaust emits excessive dense blue smoke during acceleration |7.3.A.2c| | 1 |
| Emissions not tested |7.0| | 1 |
| Emissions not tested |8.2.1.2 |d|| | 1 |
| Front brake disc excessively pitted |3.5.1h| | 1 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Front brake disc excessively pitted |3.5.1h| | 1 |
| Rear Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.3.D.1| | 1 |
| Fuel system component leaking filter |7.2.3| | 1 |
| Rear fog lamp missing |1.3.2a| | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 1 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor (6.2.2 (d) (i)) | 1 |
| Rear fog lamp switch inoperative (4.5.3 (a) (ii)) | 1 |
| Rear brake application uneven | 1 |
| Nearside Front front brake binding (3.7.B.1) | 1 |
| Offside Front front brake binding (3.7.B.1) | 1 |
| Service brake: efficiency below requirements (3.7.B.7) | 1 |
| Rear fog lamp not working (1.3.2b) | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill corrosion (7.1.1 (a) (i)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill corrosion (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill corrosion (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill corrosion (5.3.6 (a) (i)) | 1 |
| Windscreen washer not working | 1 |
| Front Headlamp not working on dipped beam both (4.1.1 (a) (ii)) | 1 |
| Headlamp not working on main beam both (4.1.1 (a) (ii)) | 1 |
| Front Position lamp not working both (4.2.1 (a) (ii)) | 1 |
| Brake performance not tested caliper loose and rear binding (1.2.1 (g)) | 1 |
| Offside Rear Brake clevis joint insecure r clip missing (1.1.15 (c)) | 1 |
| Offside Front Brake disc significantly and obviously worn pad contact area severely reduced (1.1.14 (a) (i)) | 1 |
| Nearside Front Hydraulic brake calliper inadequately mounted bolt missing (1.1.16 (c) (i)) | 1 |
| Offside Rear Wheel bearing has excessive play not tested as brakes too tight (5.1.3 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases possible rear silencer behind heat shield (6.1.2 (a)) | 1 |
| Main beam tell-tale not working (4.9.1 (a) (ii)) | 1 |
| Central Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill below trailing arm bush (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Emissions not tested (8.2.1.2 (d)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Nearside Rear Boot lid insecure boot hinge insecure (6.2.1 (a) (i)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill corroded and holed (7.1.1 (a) (i)) | 1 |
| Nearside Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Cross member (5.3.6 (a) (i)) | 1 |
| Central Front Seat belt anchorage prescribed area strength or continuity significantly reduced Nearside (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Central Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced Offside (7.1.1 (a) (i)) | 1 |
| Nearside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Anti-roll bar attachment bracket/mounting corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 1 |
| Rear Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Front Suspension arm attachment bracket/mounting corroded and seriously weakened the floor area beside the lower arm rear mounting requires welding (5.3.3 (b) (i)) | 1 |