Most common failures | No# failures |
---|
Brake pipe excessively corroded | 432 |
Windscreen wiper does not clear the windscreen effectively | 368 |
Registration plate lamp issues | 323 |
Headlamp aim out of alignment | 294 |
Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 210 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 201 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 167 |
Registration plate issues | 128 |
Brake hose excessively deteriorated | 120 |
Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 114 |
Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 106 |
Exhaust has a major leak of exhaust gases |7.1.2| | 104 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 100 |
Parking brake: efficiency below requirements |3.7.B.7| | 91 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 84 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 84 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 81 |
Brakes imbalanced across an axle | 74 |
Brake pedal anti-slip provision missing |3.3.A.1b| | 73 |
Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 73 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 70 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 69 |
Nearside Front coil spring fractured |2.4.C.1a| | 65 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 62 |
Offside Stop lamp not working |1.2.1b| | 62 |
Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 62 |
Windscreen has damage | 60 |
Nearside Stop lamp not working |1.2.1b| | 60 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 59 |
Front brake disc in such a condition that it is seriously weakened | 58 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 57 |
Rear brake application uneven | 56 |
Emissions not tested |7.0| | 55 |
Rear parking brake recording little or no effort | 55 |
Offside Front coil spring fractured |2.4.C.1a| | 54 |
Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 53 |
Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 53 |
Offside Front position lamp|s| not working |1.1.A.3b| | 52 |
Rear brake binding | 49 |
Service brake: efficiency below requirements |3.7.B.7| | 45 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 38 |
Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 36 |
Nearside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 35 |
Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 34 |
Nearside Rear Stop lamp not working |1.2.1b| | 34 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 33 |
Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 32 |
Offside Front coil spring incomplete |2.4.C.1a| | 32 |
Offside Rear fog lamp not working |1.3.2b| | 30 |
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 29 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 29 |
Horn not working |1.6.2a| | 28 |
Nearside Front coil spring incomplete |2.4.C.1a| | 27 |
Offside Rear Stop lamp not working |1.2.1b| | 27 |
Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 26 |
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 24 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 24 |
Battery insecure |1.9.1| | 23 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 23 |
Nearside Front wheel bearing has excessive play |2.5.A.3c| | 22 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 22 |
Hazard warning switch faulty |1.4.B.1d| | 22 |
Offside Front wheel bearing has excessive play |2.5.A.3c| | 21 |
Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 20 |
Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 20 |
Offside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 19 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 19 |
Exhaust system not adequately supported |7.1.1| | 18 |
Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 18 |
Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 18 |
Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 18 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 18 |
Parking brake lever has no reserve travel |3.1.6b| | 17 |
Offside Front Front position lamp|s| not working |1.1.A.3b| | 17 |
Body has a sharp edge caused by corrosion |6.1.C.1| | 17 |
Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 16 |
Nearside Headlamp not working on main beam |1.7.5a| | 16 |
Nearside Windscreen wiper blade deteriorated |8.2.2| | 16 |
Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 15 |
Offside Headlamp not working on dipped beam |1.7.5a| | 15 |
Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 15 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 15 |
Offside Windscreen wiper blade deteriorated |8.2.2| | 14 |
Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 14 |
Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 14 |
Exhaust has part of the system excessively deteriorated |7.1.1a| | 14 |
Nearside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 14 |
Brake load sensing valve linkage defective and function impaired |3.6.E.3| | 13 |
Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 13 |
Offside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 13 |
Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 12 |
Brake load sensing valve linkage seized |3.6.E.3| | 12 |
Power steering pump leaking from a failed seal |2.3.3b| | 12 |
Nearside Inner Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 12 |
Nearside Rear Leaf spring fractured |2.4.B.1a| | 12 |
Offside Front brake disc excessively pitted |3.5.1h| | 11 |
Rear Exhaust system not adequately supported |7.1.1| | 11 |
Offside Track rod end ball joint has excessive play |2.2.B.1f| | 11 |
Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 11 |
Nearside Rear Body has a sharp edge caused by damage |6.1.C.1| | 11 |
Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 11 |
Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 11 |
Power steering pump leaking from a failed component |2.3.3b| | 11 |
Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 11 |
Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 11 |
Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 11 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 11 |
Nearside Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 11 |
Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 10 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded which significantly reduces the original strength |2.4.A.2| | 10 |
Nearside Front Headlamp not working on dipped beam |1.7.5a| | 10 |
Offside Rear Exhaust has a major leak of exhaust gases |7.1.2| | 10 |
Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 10 |
Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.3.D.1| | 10 |
Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 10 |
Centre Exhaust system not adequately supported |7.1.1| | 10 |
Nearside Front coil spring broken |2.4.C.1a| | 10 |
Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 10 |
Offside Rear Body has a sharp edge caused by damage |6.1.C.1| | 10 |
Nearside Front wheel bearing rough when rotated |2.5.A.2| | 10 |
Offside Rear position lamp|s| incomplete |1.1.4a| | 10 |
Nearside Front brake disc excessively pitted |3.5.1h| | 10 |
Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 10 |
Power steering fluid level below minimum |2.3.1| | 10 |
Nearside Rear Lower Shock absorber has an excessively worn bush |2.7.4| | 9 |
Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 9 |
Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 9 |
Offside Rear Rear fog lamp not working |1.3.2b| | 9 |
Rear Mechanical brake component has restricted free movement | 9 |
Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 9 |
Driver`s seat insecure |6.2.A.1| | 9 |
Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 9 |
Nearside Front coil spring cracked |2.4.C.1a| | 9 |
Nearside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 9 |
Centre Exhaust has part of the system excessively deteriorated |7.1.1a| | 9 |
Offside Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 9 |
Offside Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 9 |
Brake pedal anti-slip provision incomplete |3.3.A.1b| | 9 |
Exhaust engine idle speed too high |7.3.D.1| | 9 |
Offside Front Headlamp not working on dipped beam |1.7.5a| | 9 |
Brake pedal spongy |3.3.B.1b| | 8 |
Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 8 |
Offside Front coil spring broken |2.4.C.1a| | 8 |
Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded which significantly reduces the original strength |2.4.A.2| | 8 |
Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 8 |
Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 8 |
Offside Front coil spring cracked |2.4.C.1a| | 8 |
Offside Rear Shock absorber has an excessively worn bush |2.7.4| | 8 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 8 |
rear brakes release unevenly |3.7.B.4| | 8 |
Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 8 |
Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 8 |
Nearside Side repeater not working |1.4.A.2c| | 8 |
Rear Exhaust has a part missing |7.1.1a| | 8 |
Offside Rear position lamp|s| not working |1.1.A.3b| | 8 |
Power steering component|s| leaking |2.3.3b| | 8 |
Nearside Rear position lamp|s| incorrect colour |1.1.A.3e| | 8 |
Nearside Stop lamp emits other than a steady red light |1.2.1e| | 8 |
Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 8 |
Nearside Inner Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 8 |
Anti-lock braking system warning lamp indicates an ABS fault | 8 |
Offside Inner Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
Nearside Steering rack gaiter split |2.2.D.2d| | 8 |
Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 8 |