| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 14 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 6 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 5 |
| Registration plate lamp issues | 5 |
| Headlamp aim out of alignment | 5 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Brakes imbalanced across an axle | 3 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 3 |
| Offside Steering rack gaiter split |2.2.D.2d| | 3 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Offside Side repeater not working |1.4.A.2c| | 3 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Front Steering rack gaiter split |2.2.D.2d| | 2 |
| Parking brake: efficiency below requirements |3.7.B.7| | 2 |
| Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 2 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 2 |
| Brake pipe excessively corroded | 2 |
| Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.3.B.1| | 2 |
| Exhaust engine idle speed too high |7.3.A.2a| | 2 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 2 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Steering column top bearing excessively worn |2.1.2c| | 2 |
| Nearside Rear Body has a projection caused by corrosion |6.1.C.1| | 2 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Driver`s seat cannot be secured in the upright position. |6.2.A.2| | 2 |
| Nearside Outer Front Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
| Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Offside Front Steering rack gaiter split |2.2.D.2d| | 1 |
| Offside Front Lower Suspension arm corroded and seriously weakened |2.4.G.1| | 1 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Horn not working (7.7 (a) (ii)) | 1 |
| Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected o/s+n/s rear crossmember (5.3.6 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area damaged to the extent that control of the vehicle is likely to be adversely affected front of spring hanger (5.3.6 (a) (ii)) | 1 |
| Nearside Suspension component ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Centre Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Rear Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Offside Rear Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Nearside Front Statutory seat belt missing |5.1.1| | 1 |
| Front Exhaust system not adequately supported |7.1.1| | 1 |
| Offside Rear Brake pipe leaking on an air braking system (1.1.11 (b) (i)) | 1 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Offside Rear Braking system leaking |3.6.A.1| | 1 |
| Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 1 |
| Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front suspension locking device missing subframe mounting bolt |2.5.A.4| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded rear mounting |2.4.A.3| | 1 |
| Offside Obligatory mirror seriously deteriorated, affecting the rear view |8.1.2a| | 1 |
| All position lamps not working |1.1.A.3b| | 1 |
| Offside Stop lamp excessively damaged so that it is not visible from a reasonable distance |1.2.1d| | 1 |
| Nearside Front Lower Suspension arm corroded and seriously weakened |2.4.G.1| | 1 |
| Nearside Front Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Lower Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Brake pedal anti-slip provision incomplete |3.3.A.1b| | 1 |
| Nearside Headlamp insecure |1.7.3| | 1 |
| Offside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
| Steering box has relative movement between sector shaft and the drop arm |2.2.B.1b| | 1 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Front brake disc excessively pitted |3.5.1h| | 1 |
| Exhaust emits dense blue smoke at idle |7.3.A.2b| | 1 |
| Nearside Stop lamp not working |1.2.1b| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Rear Braking system leaking |3.6.A.1| | 1 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Rear parking brake recording little or no effort | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill panel/ inner sill (6.2.2 (d) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area is excessively corroded sill/box section |2.4.A.3| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded sill/box section |2.4.A.3| | 1 |
| Nearside Front Leaf spring shackle bracket corroded and seriously weakened |5.3.1 |b| |i|| | 1 |
| Offside Front Hydraulic brake calliper leaking |1.1.16 |b| |i|| | 1 |
| Offside Rear Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear position lamp|s| incomplete |1.1.4a| | 1 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Rear Brake valve leaking |3.6.A.1| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Battery insecure and likely to fall from carrier Both (4.13 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Nearside Side repeater not working |1.4.A.2c| | 1 |
| Battery insecure |1.9.1| | 1 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Rear brake binding | 1 |
| Nearside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Offside Rear Body has a projection caused by corrosion |6.1.C.1| | 1 |
| Offside Rear Leaf spring has excessive side play at eye |anchor| |2.4.B.4| | 1 |
| Brake pedal pad not secure to the pedal |3.3.A.1c| | 1 |
| Registration plate issues | 1 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 1 |
| Nearside rear brake juddering severely |3.7.A.5b| | 1 |
| Offside rear brake juddering severely |3.7.A.5b| | 1 |
| Nearside Front Battery insecure |1.9.1| | 1 |
| Offside Front Battery insecure |1.9.1| | 1 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Rear position lamp|s| adversely affected by the operation of another lamp both sides |1.1.A.3f| | 1 |
| Offside Battery insecure |1.9.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings step |underbody| |6.1.B.2| | 1 |
| Offside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Rear Upper Suspension component mounting prescribed area is excessively corroded chassis rail |2.4.A.3| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded inner step/door shut |5.2.6| | 1 |
| Front Outer Body has a sharp edge caused by corrosion wheel arches both sides |6.1.C.1| | 1 |
| Front Body has a sharp edge caused by corrosion bonnet |underside| |6.1.C.1| | 1 |
| Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Nearside Front Passenger`s seat insecure |6.2.A.1| | 1 |
| Offside Bonnet retaining device ineffective |8.4.2| | 1 |
| Nearside Inner Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Outer Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Battery insecure and likely to fall from carrier both battery tray|s| corroded |4.13 |a| |ii|| | 1 |
| Exhaust has a major leak of exhaust gases manifold downpipe joining flange |6.1.2 |a|| | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment |1.1.6 |c|| | 1 |
| Nearside Side repeater not working |4.4.1 |a| |ii|| | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross-member/panel |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill |6.2.2 |d| |i|| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Nearside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower wheel arch both sides |5.3.6 |a| |i|| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Rear Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Front Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wheel arch/step area |6.1.B.2| | 1 |
| Offside Front Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings wheel arch/step area |6.1.B.2| | 1 |
| Offside Rear Suspension spring mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Nearside Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |