Most common failures | No# failures |
---|
Headlamp aim out of alignment | 13 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 12 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 10 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
Registration plate lamp issues | 6 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 6 |
Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 6 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 5 |
Brakes imbalanced across an axle | 4 |
Rear parking brake recording little or no effort | 4 |
Windscreen wiper does not clear the windscreen effectively | 4 |
Rear brake binding | 3 |
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
Front brake application uneven | 3 |
Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 3 |
Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
Horn not working |1.6.2a| | 3 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Rear Rear wheel bearing rough when rotated |2.6.1| | 2 |
Front Windscreen wiper blade deteriorated |8.2.2| | 2 |
Service brake: efficiency below requirements |3.7.B.7| | 2 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Offside Rear fog lamp not working |1.3.2b| | 2 |
Nearside Headlamp not working on main beam |1.7.5a| | 2 |
Nearside Rear Rear wheel bearing has excessive play |2.6.2| | 2 |
Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 2 |
Offside Front Front wheel bearing rough when rotated |2.5.A.2| | 2 |
Offside Front position lamp|s| not working |1.1.A.3b| | 2 |
Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 2 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Rear wheel bearing has excessive play |2.6.2| | 2 |
Offside Rear wheel bearing has excessive play |2.6.2| | 2 |
Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Outer Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Front Direction indicator incorrect colour |1.4.A.2f| | 2 |
Parking brake: efficiency below requirements |3.7.B.7| | 2 |
Nearside Rear wheel bearing rough when rotated |2.6.1| | 2 |
Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
Offside Rear Rear wheel bearing rough when rotated |2.6.1| | 2 |
Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
Steering rack damaged and unserviceable |2.2.C.1d| | 1 |
Offside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
Nearside Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Nearside Steering rack gaiter split |2.2.D.2d| | 1 |
Nearside Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Front Headlamp not working on main beam |1.7.5a| | 1 |
Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
Nearside Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front brake disc excessively pitted |3.5.1h| | 1 |
Brake pedal creeps down while the pedal is held under pressure |3.3.B.1a| | 1 |
Nearside Steering system has excessive free play detected at the steering wheel |steering rack fitted| |2.2.A.1b| | 1 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
Steering column top bearing excessively worn |2.1.2c| | 1 |
Nearside Shock absorber has negligible damping effect |2.7.5| | 1 |
Offside Shock absorber has negligible damping effect |2.7.5| | 1 |
Position lamp switch faulty |1.1.A.1| | 1 |
Offside Headlamp not working on main beam |1.7.5a| | 1 |
Offside Rear Direction indicator not working |1.4.A.2c| | 1 |
Offside Rear Rear fog lamp not working |1.3.2b| | 1 |
Offside Front Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Offside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded X member |2.4.A.3| | 1 |
Offside Front Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength X member |2.4.A.3| | 1 |
Nearside Rear Upper Suspension component mounting prescribed area is excessively corroded Shock absober mount |2.4.A.3| | 1 |
Nearside Front Lower Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength suspension arm mount |2.4.A.3| | 1 |
Offside Rear Stop lamp not working |1.2.1b| | 1 |
Nearside Rear Upper Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Nearside Rear Lower Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Nearside Front Lower Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded chassis |2.4.A.3| | 1 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded chassis |2.4.A.3| | 1 |
Nearside Rear Brake pipe inadequately supported |3.6.B.1| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded anti-roll bar |2.4.A.3| | 1 |
Offside Rear coil spring incomplete |2.4.C.1a| | 1 |
Nearside Front Lower Ball joint has excessive play |2.2.B.1f| | 1 |
Nearside Steering rack damaged and unserviceable |2.2.C.1d| | 1 |
Offside Steering rack damaged and unserviceable |2.2.C.1d| | 1 |
Nearside Front Lower Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
Offside Front Lower Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
Nearside Front Steering rack gaiter split |2.2.D.2d| | 1 |
Nearside Side repeater not working |1.4.A.2c| | 1 |
Nearside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.2| | 1 |
Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 1 |
Nearside Rear Seat belt retracting mechanism defective |5.2.5b| | 1 |
Offside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Steering rack gaiter split |2.2.D.2d| | 1 |
Nearside Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
Offside Headlamp aim beam image too far to the left |1.6.B4| | 1 |
Nearside Headlamp aim beam image too far to the left |1.6.B4| | 1 |
Fuel system component leaking |7.2.3| | 1 |
Nearside Front coil spring fractured |2.4.C.1a| | 1 |
Offside Rear Brake actuating linkage mounting prescribed area is excessively corroded |3.3.A.2| | 1 |
Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Outer Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Headlamp aim beam image kick up to the offside |1.8| | 1 |
Offside Headlamp aim beam image kick up to the offside |1.8| | 1 |
Centre Rear Stop lamp not working |1.2.1b| | 1 |
Offside Rear Seat belt has a cut which has significantly weakened the webbing |5.2.2a| | 1 |
Nearside Inner Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Brake hose excessively deteriorated | 1 |
Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Rear Seat belt damaged sufficient to obstruct correct operation of the belt |5.2.2a| | 1 |
Headlamp aim beam image kick up to the offside |1.8| | 1 |
Centre Stop lamp not working |1.2.1b| | 1 |
Nearside Front Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Exhaust mounting missing |7.1.1b| | 1 |
Nearside Stop lamp not working |1.2.1b| | 1 |
Brake pipe excessively corroded | 1 |
Offside Steering rack gaiter split |2.2.D.2d| | 1 |
Nearside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Nearside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 1 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Hazard warning switch faulty |1.4.B.1d| | 1 |
Offside Rear Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 1 |
Offside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Headlamp insecure |1.7.3| | 1 |
Nearside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
Offside Rear Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Rear Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Rear Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Offside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Offside Rear wheel bearing rough when rotated |2.6.1| | 1 |
Nearside front brake binding |3.7.B.1| | 1 |
Nearside Front An item not tested |Manual| | 1 |
Rear Fuel hose leaking |7.2.3| | 1 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 1 |
Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front passenger seat insecure |6.2.3| | 1 |
Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Front brake disc excessively pitted |3.5.1h| | 1 |
Offside Inner Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 1 |
Registration plate issues | 1 |
Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Nearside Front brake caliper has restricted free movement |3.5.1k| | 1 |
Nearside Front front brake binding |3.7.B.1| | 1 |
Nearside Windscreen wiper blade deteriorated |8.2.2| | 1 |
Offside Windscreen wiper blade deteriorated |8.2.2| | 1 |
Nearside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |