Most common failures | No# failures |
---|
Headlamp aim out of alignment | 75 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 54 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 45 |
Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 41 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 40 |
Registration plate lamp issues | 38 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 37 |
Brake pipe excessively corroded | 33 |
Brake hose excessively deteriorated | 27 |
Windscreen wiper does not clear the windscreen effectively | 25 |
Rear brake binding | 21 |
Brakes imbalanced across an axle | 17 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 16 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 15 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 15 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 14 |
Registration plate issues | 14 |
Parking brake: efficiency below requirements |3.7.B.7| | 13 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 12 |
Offside Front constant velocity joint gaiter split |2.5.C.1a| | 11 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 11 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 11 |
Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 10 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 10 |
Rear brake application uneven | 10 |
Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 10 |
Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 9 |
Service brake: efficiency below requirements |3.7.B.7| | 8 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
Offside Rear fog lamp not working |1.3.2b| | 8 |
Offside Rear coil spring fractured |2.4.C.1a| | 8 |
Exhaust has a major leak of exhaust gases |7.1.2| | 8 |
Nearside Rear wheel bearing has excessive play |2.6.2| | 8 |
Rear parking brake recording little or no effort | 8 |
Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 8 |
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 8 |
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 8 |
Front brake disc in such a condition that it is seriously weakened | 8 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 7 |
Offside Headlamp not working on dipped beam |1.7.5a| | 7 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 7 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 6 |
Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
Brake pipe inadequately clipped |3.6.B.1| | 6 |
Offside Rear Stop lamp not working |1.2.1b| | 6 |
Nearside Front coil spring fractured |2.4.C.1a| | 6 |
Offside Rear wheel bearing rough when rotated |2.6.1| | 6 |
Offside Rear wheel bearing has excessive play |2.6.2| | 6 |
Offside Stop lamp not working |1.2.1b| | 6 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 6 |
Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 6 |
Nearside Rear Stop lamp not working |1.2.1b| | 6 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 6 |
Nearside Windscreen wiper blade deteriorated |8.2.2| | 5 |
Nearside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
Horn not working |1.6.2a| | 5 |
Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
Offside Front position lamp|s| not working |1.1.A.3b| | 5 |
Rear Mechanical brake component has restricted free movement | 5 |
Nearside Front wheel bearing rough when rotated |2.5.A.2| | 5 |
Nearside Front Shock absorber has negligible damping effect |2.7.5| | 5 |
Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 5 |
Parking brake lever has no reserve travel |3.1.6b| | 5 |
Nearside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
Offside Front Front position lamp|s| not working |1.1.A.3b| | 4 |
Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 4 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 4 |
Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
Nearside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 4 |
Nearside Steering rack gaiter split |2.2.D.2d| | 4 |
Nearside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
Nearside Rear wheel bearing rough when rotated |2.6.1| | 4 |
Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 4 |
Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 4 |
Nearside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 4 |
Offside rear brake recording little or no effort |3.7.B.5a| | 4 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
Nearside Rear Seat belt locking mechanism does not secure or release |5.2.5a| | 4 |
Offside Front Shock absorber has negligible damping effect |2.7.5| | 4 |
Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 4 |
Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 4 |
Offside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
Offside Front Headlamp not working on dipped beam |1.7.5a| | 4 |
Fuel system component insecure |7.2.1| | 4 |
Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 4 |
Offside Front coil spring incomplete |2.4.C.1a| | 4 |
Offside Headlamp insecure |1.7.3| | 4 |
Offside Windscreen wiper blade deteriorated |8.2.2| | 3 |
Offside Headlamp not working on main beam |1.7.5a| | 3 |
Nearside Rear Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
Offside Side repeater not working |1.4.A.2c| | 3 |
Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 3 |
Offside Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Front brake application uneven | 3 |
Nearside Stop lamp not working |1.2.1b| | 3 |
Centre Rear Statutory seat belt missing |5.1.1| | 3 |
Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Position lamp switch faulty |1.1.A.1| | 3 |
Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 3 |
Offside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 3 |
Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 3 |
Offside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 3 |
Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Rear Rear wheel bearing has excessive play |2.6.2| | 3 |
Nearside Rear Rear wheel bearing rough when rotated |2.6.1| | 3 |
Nearside Side repeater not working |1.4.A.2c| | 3 |
Rear Body has a sharp edge caused by damage |6.1.C.1| | 3 |
Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Stop lamp not working |1.2.1b| | 3 |
Centre Exhaust has part of the system excessively deteriorated |7.1.1a| | 3 |
Nearside Headlamp insecure |1.7.3| | 3 |
Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 3 |
Nearside Front Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 3 |
Offside Front wheel bearing rough when rotated |2.5.A.2| | 3 |
Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 3 |
Offside Rear Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 3 |
Offside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 3 |
Nearside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Offside Rear position lamp|s| incomplete |1.1.4a| | 3 |
Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 3 |
Nearside Front Headlamp not working on dipped beam |1.7.5a| | 3 |
Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 3 |
Offside Front Headlamp not working on main beam |1.7.5a| | 3 |
Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 3 |
Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 3 |
Offside Track rod end ball joint has excessive play |2.2.B.1f| | 3 |
Stop lamp remains on when the brakes are released | 3 |
Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 3 |
Windscreen wiper blade insecure | 3 |
Offside Front coil spring fractured |2.4.C.1a| | 3 |
Offside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Front Upper Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 2 |
Offside Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 2 |
Offside Outer Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Rear wheel cylinder leaking |3.6.A.1| | 2 |
Offside Front Brake actuating linkage mounting prescribed area is excessively corroded |3.3.A.2| | 2 |
Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Windscreen wiper blade deteriorated |8.2.2| | 2 |
Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 2 |
Nearside Rear Body has a sharp edge caused by damage |6.1.C.1| | 2 |
Offside Front Windscreen wiper blade deteriorated |8.2.2| | 2 |
Nearside Front Body has a sharp edge caused by damage |6.1.C.1| | 2 |
Nearside Rear Seat belt retracting mechanism defective |5.2.5b| | 2 |
Windscreen has damage | 2 |
Offside Obligatory mirror insecure |8.1.1| | 2 |
Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Rear coil spring incomplete |2.4.C.1a| | 2 |
Nearside Front Direction indicator incorrect colour |1.4.A.2f| | 2 |
Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
Nearside Rear Body or chassis is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Offside Rear Body or chassis is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Offside front brake binding |3.7.B.1| | 2 |
Brake hose damaged | 2 |
Nearside Front coil spring incomplete |2.4.C.1a| | 2 |
Fuel cap/sealing device sealing washer missing |7.2.4c| | 2 |
rear brakes release unevenly |3.7.B.4| | 2 |
Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 2 |
Rear Rear fog lamp tell tale not working |1.3.1b| | 2 |
Rear Statutory seat belt missing |5.1.1| | 2 |
Rear Rear fog lamp not working |1.3.2b| | 2 |
Offside Rear rear brake recording little or no effort |3.7.B.5a| | 2 |
Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Offside Front Body has a sharp edge caused by damage |6.1.C.1| | 2 |
Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 2 |
Offside Rear Seat belt locking mechanism does not secure or release |5.2.5a| | 2 |
Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Front front brake binding |3.7.B.1| | 2 |
Brake servo leaking |3.6.C.1c| | 2 |
Offside Front coil spring broken |2.4.C.1a| | 2 |
Nearside Rear coil spring broken |2.4.C.1a| | 2 |
Offside Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
Offside Rear Body has a sharp edge caused by damage |6.1.C.1| | 2 |
Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition |7.1.4| | 2 |
Nearside Steering locking device missing |2.2.C.1g| | 2 |
Nearside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 2 |
Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Nearside Rear Shock absorber has negligible damping effect |2.7.5| | 2 |
Offside Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Offside Headlamp not in a clean condition affecting beam image |1.2.4a| | 2 |
Windscreen washer control missing |8.2.1a| | 2 |
Offside Inner Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Front wheel bearing has excessive play |2.5.A.3c| | 2 |
Bonnet cannot be secured in the closed position |8.4.1| | 2 |
Offside Rear coil spring incomplete |2.4.C.1a| | 2 |
Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Rear front brake binding |3.7.B.1| | 2 |
Offside Rear Shock absorber has negligible damping effect |2.7.5| | 2 |
Offside Rear Rear fog lamp not working |1.3.2b| | 2 |
Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Offside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Bootlid cannot be secured in the closed position |6.4.1| | 2 |
Brake pedal anti-slip provision incomplete |3.3.A.1b| | 2 |
Offside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
Front Body has a sharp edge caused by damage |6.1.C.1| | 2 |
Battery insecure |1.9.1| | 2 |