Most common failures | No# failures |
---|
Windscreen wiper does not clear the windscreen effectively | 28 |
Registration plate lamp issues | 11 |
Brake pipe excessively corroded | 9 |
Brakes imbalanced across an axle | 9 |
Headlamp aim out of alignment | 8 |
Rear fog lamp not working |1.3.2b| | 7 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
Rear brake binding | 6 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
Offside Rear fog lamp emits a light other than red |1.3.2e| | 5 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
Offside Front position lamp|s| not working |1.1.A.3b| | 5 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
Exhaust has a major leak of exhaust gases |7.1.2| | 4 |
Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
Nearside Rear Stop lamp not working |1.2.1b| | 4 |
Battery insecure |1.9.1| | 4 |
Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Offside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 3 |
Offside front brake binding |3.7.B.1| | 3 |
Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Rear brake disc contaminated by oil |3.5.1h| | 3 |
Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Rear Exhaust emits excessive smoke or vapour likely to obscure the vision of other road users (8.2.2.2 (c)) | 3 |
Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 3 |
Brake hose excessively deteriorated | 3 |
Offside Rear fog lamp not working |1.3.2b| | 3 |
Nearside Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Exhaust has part of the system excessively deteriorated |7.1.1a| | 2 |
Offside Rear Rear fog lamp emits a light other than red |1.3.2e| | 2 |
Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 2 |
Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
Nearside Stop lamp not working |1.2.1b| | 2 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 2 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 2 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Offside Rear position lamp|s| not working |1.1.A.3b| | 2 |
Offside Stop lamp not working |1.2.1b| | 2 |
Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 2 |
Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Windscreen washer not working | 2 |
Nearside Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 2 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
Offside Front Position lamp not working |4.2.1 |a|| | 2 |
Battery insecure and likely to fall from carrier |4.13 |a| |ii|| | 2 |
Service brake efficiency below requirements |1.2.2 |a| |i|| | 2 |
Nearside Front brake disc excessively pitted |3.5.1h| | 2 |
Offside Front brake disc excessively pitted |3.5.1h| | 2 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Offside Inner Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Rear fog lamp insecure |1.3.2a| | 2 |
Nearside Rear Position lamp not working |4.2.1 |a|| | 2 |
Parking brake: efficiency below requirements |3.7.B.7| | 2 |
Stop lamp|s| all not working |4.3.1 |a| |iii|| | 2 |
Service brake: efficiency below requirements |3.7.B.7| | 2 |
Offside Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 2 |
Nearside Rear Lower Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 2 |
Rear Suspension component mounting prescribed area is excessively corroded o/s and n/s |2.4.A.3| | 2 |
Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Offside Rear Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 2 |
Nearside Inner Rear brake disc excessively pitted |3.5.1h| | 1 |
Offside Inner Rear brake disc excessively pitted |3.5.1h| | 1 |
Parking brake: efficiency below requirements |3.7.C.1b| | 1 |
Exhaust noise is clearly in excess of that emitted by a similar vehicle fitted with a standard silencer in average condition |7.1.4| | 1 |
Offside Front Obligatory mirror missing |8.1.1| | 1 |
Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Rear Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 1 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
Exhaust emits excessive smoke or vapour of any colour |7.4.B.4| | 1 |
Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` items hanging from interior mirror |8.3.1e| | 1 |
Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Offside Headlamp adversely affected by the operation of another lamp dip/main beam operation |1.7.5c| | 1 |
Rear fog lamp emits a light other than red emits pink light |1.3.2e| | 1 |
Offside Battery insecure |1.9.1| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded lower suspension arm mount/inner sill |2.4.A.3| | 1 |
Rear brake disc in such a condition that it is seriously weakened | 1 |
Offside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
Rear fog lamp emits a light other than red |1.3.2e| | 1 |
Offside Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
Offside Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside front brake binding |3.7.B.1| | 1 |
Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside brake disc in such a condition that it is seriously weakened |3.5.1i| | 1 |
Offside Inner Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Rear fog lamp tell tale missing |1.3.1b| | 1 |
Offside Front Seat belt stitching badly frayed |5.2.2b| | 1 |
Offside Rear Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 1 |
Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 1 |
Nearside Rear Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
Offside Rear Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
Nearside Rear Anti-roll bar pin or bush excessively worn D bush |5.3.4 |a| |i|| | 1 |
Offside Rear Anti-roll bar pin or bush excessively worn D bush |5.3.4 |a| |i|| | 1 |
Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
Nearside Rear Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
Rear Body insecure and dangerous to other road users |6.1.B.1b| | 1 |
Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Fuel cap/sealing device missing |7.2.4a| | 1 |
Offside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Exhaust emits excessive smoke or vapour likely to obscure the vision of other road users (8.2.2.2 (c)) | 1 |
Offside Rear Body component damaged and likely to cause injury wheel arch (6.2.1 (a) (i)) | 1 |
Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Nearside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
Central Prop shaft bearing likely to break up (6.1.7 (b) (ii)) | 1 |
Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 1 |
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wing (6.1.1 (c) (i)) | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced out rigger (6.1.1 (c) (i)) | 1 |
Nearside Front Inner Vehicle structure is fractured and structural rigidity is significantly reduced wing (6.1.1 (a) (i)) | 1 |
Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting foot well area (6.2.2 (d) (i)) | 1 |
Offside Front Lower Suspension arm ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting side sill inner and outer (6.2.2 (d) (i)) | 1 |
Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting side sill (6.2.2 (d) (i)) | 1 |
Front Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
Front Bumper insecure (6.1.4 (a) (i)) | 1 |
Offside Rear Inner Suspension component mounting prescribed area is inadequately repaired O/S/R Inner & Outer sill... O/S/R Front leaf-spring mounting point prescribed area . |5.3.6 |a| |i|| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Cross-member... 0/S/F Bottom-arm, front mounting point prescribed area. |5.3.6 |a| |i|| | 1 |
Central Drive shaft bearing excessively worn Prop-shaft center bearing. |6.1.7 |b| |i|| | 1 |
Registration plate issues | 1 |
Nearside Front Wheel bearing has excessive play |5.1.3 |a| |i|| | 1 |
Offside Brake master cylinder/servo mounting prescribed area is excessively corroded 2 places inside wheel arch |3.6.C.3| | 1 |
Nearside Front Suspension spring mounting prescribed area is excessively corroded x2 places |2.4.A.3| | 1 |
Nearside Front coil spring broken |2.4.C.1a| | 1 |
Nearside Front Suspension spring mounting prescribed area is excessively corroded Bottom wishbone |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded Inner arch |2.4.A.3| | 1 |
Rear Suspension component mounting prescribed area is excessively corroded Complete rear cross member |2.4.A.3| | 1 |
Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings NS WHEEL ARCH/BOTH FRONT ARCHES/FRONT CROSS MEMBER/NS REAR QUARTER/NS SILL/FRONT SUBFRAME/ NS SILL FOOTWELL/DRIVERS FOOTWELL |6.1.B.2| | 1 |
Nearside Rear Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings under arch |6.1.B.2| | 1 |
Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Front arches |6.1.B.2| | 1 |
Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Front subframe |6.1.B.2| | 1 |
Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings NS Rear quarter |6.1.B.2| | 1 |
Nearside Rear Lower Shock absorber has an excessively worn bush |2.7.4| | 1 |
Offside Rear Lower Shock absorber has an excessively worn bush |2.7.4| | 1 |
Offside rear brake excessively fluctuating |3.7.B.3| | 1 |
Offside Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Front Position lamp not working o/s and n/s |4.2.1 |a|| | 1 |
Nearside Side repeater not working |1.4.A.2c| | 1 |
Nearside Front Suspension spring mounting prescribed area is excessively corroded front mounting |2.4.A.3| | 1 |
Offside Front Suspension spring mounting prescribed area is excessively corroded front mounting |2.4.A.3| | 1 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded rear mounting |2.4.A.3| | 1 |
Front Anti-roll bar has excessive play in a pin/bush both d bushes |2.4.G.2| | 1 |
Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
Offside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded inner front panel |2.4.A.3| | 1 |
Nearside Front Subframe mounting prescribed area is excessively corroded inner front panel |2.4.A.3| | 1 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded rear panel |2.4.A.3| | 1 |
Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting rear panel |6.6.6| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded inner wing near top shocker mount area |2.4.A.3| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded inner wing near top shocker mount area |2.4.A.3| | 1 |
Headlamp aim not tested |4.1.2 |b|| | 1 |
Nearside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Nearside Front Position lamp not working |4.2.1 |a|| | 1 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner and outer sill under door step |6.1.B.2| | 1 |
Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Towbar excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Rear Upper Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced rear cross member spring hangers (6.1.1 (c) (i)) | 1 |
Offside Rear Upper Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced rear cross member spring hagers (6.1.1 (c) (i)) | 1 |
Nearside Front Upper Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced front chassis rail (6.1.1 (c) (i)) | 1 |
Offside Front Upper Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis rail (6.1.1 (c) (i)) | 1 |
Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced within 30cm of chassis rail (6.1.1 (c) (i)) | 1 |
Offside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced 30 cm from seat belt mount (6.1.1 (c) (i)) | 1 |
Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced within 30 cm of chassis rail (6.1.1 (c) (i)) | 1 |
Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced within 30 cm of chassis rail (6.1.1 (c) (i)) | 1 |
Nearside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill not seem welded (6.1.1 (c) (i)) | 1 |
Horn not working (7.7 (a) (ii)) | 1 |
Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wing and battery tray (6.1.1 (c) (i)) | 1 |
Nearside Front Inner Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected shock top mount (5.3.6 (a) (ii)) | 1 |
Brake performance not tested (1.2.1 (g)) | 1 |
Nearside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Nearside Front Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
Offside Front Headlamp insecure |1.7.3| | 1 |
Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Shock absorber has an excessively worn bush |2.7.4| | 1 |
Offside Front brake disc excessively scored |3.5.1h| | 1 |
Front brake application uneven | 1 |
Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Offside Headlamp aim beam image kick up to the offside |1.8| | 1 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded around shock absorber mounting |2.4.A.3| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded lower suspension arm mounting area |2.4.A.3| | 1 |
Offside Front Suspension component mounting prescribed area is inadequately repaired lower suspension front mounting area |2.4.A.3| | 1 |
Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
Nearside Rear Braking system leaking caliper |3.6.A.1| | 1 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
Nearside Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
Offside Front Service brake excessively binding |1.2.1 |f|| | 1 |
Offside Battery insecure and likely to fall from carrier |4.13 |a| |ii|| | 1 |
Exhaust has a major leak of exhaust gases middle section leaking |7.1.2| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded sill corroded rear susspension |2.4.A.3| | 1 |
Exhaust emissions exceed level of metered smoke for a non-turbo charged engine (8.2.2.2 (b)) | 1 |
Nearside Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
Nearside Rear Road wheel fixing missing (5.2.1 (a) (i)) | 1 |
Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area is inadequately repaired inner arch section (5.3.6 (a) (i)) | 1 |
Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Step section (6.1.1 (c) (i)) | 1 |
Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced step section (6.1.1 (c) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch section (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch area (5.3.6 (a) (i)) | 1 |
Central Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced cross member (6.1.1 (c) (i)) | 1 |
Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 1 |
Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 1 |
Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Next to battery tray (6.2.2 (d) (i)) | 1 |
Central Rear Towbar with an unsafe modification to primary components (6.1.6 (g) (ii)) | 1 |
Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
Nearside Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced centre sill (6.1.1 (c) (i)) | 1 |
Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Wheel arch corroded (6.1.1 (c) (i)) | 1 |
Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Wheel arch (6.1.1 (c) (i)) | 1 |
Nearside Rear Road wheel fixing missing Wheel nut missing (5.2.1 (a) (i)) | 1 |
Front Exhaust system not adequately supported |7.1.1| | 1 |
Offside Outline marker lamp missing (4.2.1 (a) (ii)) | 1 |
Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |
Nearside Direction indicator not working |4.4.1 |a| |ii|| | 1 |
Offside Rear Position lamp not working |4.2.1 |a|| | 1 |
Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced both sills (6.1.1 (c) (i)) | 1 |
Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced both sills (6.1.1 (c) (i)) | 1 |
Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Both inner archs (6.1.1 (c) (i)) | 1 |
Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Parking (secondary brake) on a single line braking system imbalanced across an axle Axle 1 (1.3.1 (b) (i)) | 1 |
Nearside Front position lamp|s| incorrect colour |1.1.A.3e| | 1 |
Offside Front position lamp|s| incorrect colour |1.1.A.3e| | 1 |
Nearside Rear brake disc contaminated by brake fluid |3.5.1h| | 1 |
Offside Inner Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Rear Braking system leaking |3.6.A.1| | 1 |
Nearside Front Wheel bearing rough when rotated |5.1.3 |b| |i|| | 1 |
Windscreen wiper blade missing |3.4 |b| |ii|| | 1 |
Offside Rear Body insecure to the extent that stability is seriously impaired shokie mount at top broken away |6.2.2 |a| |ii|| | 1 |
Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
Nearside Rear brake drum contaminated by oil |3.5.1h| | 1 |
Offside Rear Lower Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
Fuel system component leaking |7.2.3| | 1 |
Nearside Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 1 |
Rear fog lamp missing |1.3.2a| | 1 |
Front Seat belt anchorage prescribed area is excessively corroded o/s and n/s |5.2.6| | 1 |
Windscreen wiper blade insecure | 1 |
Nearside Inner Front Lower Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Offside Seat belt anchorage prescribed area strength or continuity significantly reduced OUTER SILL (7.1.1 (a) (i)) | 1 |
Offside Seat belt anchorage prescribed area strength or continuity significantly reduced INNER SILL (7.1.1 (a) (i)) | 1 |
Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced INNER SILL (7.1.1 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER ARCH (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER SILL (5.3.6 (a) (i)) | 1 |
Service brake grabbing severely (1.2.1 (c)) | 1 |
Offside Rear Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
Nearside Inner Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Inner Rear Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 1 |
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 1 |
Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Front Anti-roll bar linkage insecure |2.4.G.1| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 1 |
front brake binding |3.7.B.1| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
Offside Front Seat belt damaged sufficient to obstruct correct operation of the belt |5.2.2a| | 1 |
Offside Front Seat belt damaged sufficient to significantly weakened the webbing |5.2.2a| | 1 |
Nearside Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Nearside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
Offside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Cross member |5.3.6 |a| |i|| | 1 |
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Cross member |5.3.6 |a| |i|| | 1 |
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Inner sill holed corroded through |5.3.6 |a| |i|| | 1 |
Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Outrigger holed corroded through |5.3.6 |a| |i|| | 1 |
Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
Centre Front Upper Brake clevis joint has restricted free movement |3.5.1k| | 1 |
Centre Front Lower Brake clevis joint has restricted free movement |3.5.1k| | 1 |
Centre Rear Brake clevis joint has restricted free movement |3.5.1k| | 1 |
Centre Front Upper Brake pivot has restricted free movement |3.5.1k| | 1 |
Brake clevis joint has restricted free movement |3.5.1k| | 1 |
Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Service brake: efficiency below requirements |3.7.C.1a| | 1 |
Centre Parking brake mechanism/associated mounting prescribed area is excessively corroded |3.1.9| | 1 |
Offside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner/outer sill |7.1.1 |a| |i|| | 1 |
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner |7.1.1 |a| |i|| | 1 |
Oil leaking excessively from transmission |8.4.1 |a| |i|| | 1 |
Front Brake disc significantly and obviously worn both |1.1.14 |a| |i|| | 1 |
Front Vehicle structure is fractured and structural rigidity is significantly reduced cross member |6.1.1 |a| |i|| | 1 |
Rear Anti-roll bar insecure |2.4.G.1| | 1 |
Nearside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
Offside Front Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Offside Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 1 |
Offside Seat belt anchorage prescribed area is excessively corroded iner sill/ floor to sill |5.2.6| | 1 |
Nearside Rear brake disc excessively pitted |3.5.1h| | 1 |
Offside Rear brake disc excessively pitted |3.5.1h| | 1 |
Horn not working |1.6.2a| | 1 |
Offside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
Offside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
Nearside Rear Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 1 |
Offside Seat belt anchorage prescribed area is excessively corroded inner cill |5.2.6| | 1 |
Offside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Nearside Rear Anti-roll bar attachment bracket/mounting nut missing |2.4.G.1| | 1 |
Offside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Inner Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear fog lamp insecure |1.3.2a| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded Top strut mounting point |2.4.A.3| | 1 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded front |2.4.A.3| | 1 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded rear |2.4.A.3| | 1 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded rear |2.4.A.3| | 1 |
Nearside Rear Shock absorber has an excessively worn bush |2.7.4| | 1 |
Offside Rear Shock absorber has an excessively worn bush |2.7.4| | 1 |
Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded inner wing/wheelarch round top shock absorber mounting |2.4.A.3| | 1 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded rear mounting area. inner sill |2.4.A.3| | 1 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded rear spring mount area. inner sill |2.4.A.3| | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chasssis |5.3.6 |a| |i|| | 1 |
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch |5.3.6 |a| |i|| | 1 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch |5.3.6 |a| |i|| | 1 |
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wing |5.3.6 |a| |i|| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength suspension mount |5.3.6 |a| |i|| | 1 |
Offside Front Anti-roll bar locating pin insecure |2.4.G.3a| | 1 |
Rear Rear fog lamp missing |1.3.2a| | 1 |
Rear fog lamp tell tale not working |1.3.1b| | 1 |
Stop lamp not working |1.2.1b| | 1 |
Offside Rear Inner Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front crossmember |5.3.6 |a| |i|| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength front crossmember |5.3.6 |a| |i|| | 1 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill end |5.3.6 |a| |i|| | 1 |
Rear Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired chassis cross member (6.2.2 (d) (ii)) | 1 |
Rear Bumper insecure (6.1.4 (a) (i)) | 1 |
Nearside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Nearside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill at rear |6.1.B.2| | 1 |
Offside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
Nearside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
Rear Exhaust has a major leak of exhaust gases section |7.1.2| | 1 |
Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering inner w/arch |6.1.1 |c| |ii|| | 1 |
Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering cross member |6.1.1 |c| |ii|| | 1 |
Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering inner w/arch |6.1.1 |c| |ii|| | 1 |
Offside Outer Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired sill |6.2.2 |d| |ii|| | 1 |
Nearside Inner Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired sill |6.2.2 |d| |ii|| | 1 |