| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 48 |
| Registration plate lamp issues | 41 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 14 |
| Offside Rear fog lamp not working |1.3.2b| | 12 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 12 |
| Headlamp aim out of alignment | 11 |
| Rear fog lamp not working |1.3.2b| | 11 |
| Brake pipe excessively corroded | 10 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 9 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 7 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 7 |
| Rear fog lamp tell tale not working |1.3.1b| | 7 |
| Battery insecure |1.9.1| | 7 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 6 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 6 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 6 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 6 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
| Offside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 6 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 5 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 5 |
| Offside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 5 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 5 |
| Nearside Stop lamp not working |1.2.1b| | 5 |
| Nearside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 5 |
| Offside Stop lamp not working |1.2.1b| | 5 |
| Offside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 4 |
| Brakes imbalanced across an axle | 4 |
| Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 4 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 4 |
| Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 4 |
| Offside Rear fog lamp emits a light other than red |1.3.2e| | 4 |
| Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 4 |
| Offside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 4 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 4 |
| Fuel system component leaking |7.2.3| | 4 |
| Parking brake lever has no reserve travel |3.1.6b| | 4 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 4 |
| Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 4 |
| Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Front Suspension arm ball joint excessively worn |5.3.4 |a| |i|| | 3 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
| Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 3 |
| Horn not working |1.6.2a| | 3 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 3 |
| Offside Rear fog lamp missing |1.3.2a| | 3 |
| Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 3 |
| Service brake: efficiency below requirements |3.7.B.7| | 3 |
| Nearside Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 3 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 3 |
| Rear fog lamp switch missing |1.3.1a| | 3 |
| Registration plate issues | 3 |
| Mechanical brake component has restricted free movement | 3 |
| Offside Front Steering rack gaiter split |2.2.D.2d| | 3 |
| Rear fog lamp emits a light other than red |1.3.2e| | 3 |
| Nearside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Rear fog lamp insecure |1.3.2a| | 2 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 2 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 2 |
| Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
| Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
| Power steering pipe|s| or hose|s| leaking from a seal |2.3.3b| | 2 |
| Nearside Rear brake disc contaminated by oil |3.5.1h| | 2 |
| Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 2 |
| Offside Steering rack gaiter split |2.2.D.2d| | 2 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 2 |
| Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 2 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 2 |
| Nearside Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 2 |
| Offside Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 2 |
| Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 2 |
| Centre Exhaust has part of the system excessively deteriorated |7.1.1a| | 2 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Nearside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Rear fog lamp insecure |1.3.2a| | 2 |
| Offside Rear Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 2 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 2 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 2 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 2 |
| Rear fog lamp missing |1.3.2a| | 2 |
| Rear fog lamp tell tale missing |1.3.1b| | 2 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 2 |
| Parking brake: efficiency below requirements |3.7.B.7| | 2 |
| Nearside Rear Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 2 |
| Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Towbar excessively corroded within 30cm of towbar mounting |6.1.6 |i| |i|| | 2 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Front An item not tested |Manual| | 1 |
| Offside Rear Suspension component mounting prescribed area is severely distorted |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area is severely distorted |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is severely distorted |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is severely distorted |5.2.6| | 1 |
| Front Subframe mounting prescribed area is severely distorted |2.4.A.3| | 1 |
| Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Rear Position lamp lens seriously defective (4.2.1 (b)) | 1 |
| Nearside Rear Bumper insecure (6.1.4 (a) (i)) | 1 |
| Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Rear Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Offside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Outline marker lamp not working |4.2.1 |a| |ii|| | 1 |
| Steering column universal joint has excessive wear or play |2.2.2 |c|| | 1 |
| Fuel system component leaking |6.1.3 |b| |i|| | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill |6.1.1 |c| |i|| | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill |6.1.1 |c| |i|| | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill |6.1.1 |c| |i|| | 1 |
| Offside Rear Anti-roll bar linkage likely to fail |5.3.3 |b| |ii|| | 1 |
| Offside Obligatory mirror insecure |3.3 |b| |ii|| | 1 |
| Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Offside Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Offside Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Brake pedal anti-slip provision missing |1.1.2 |c|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Front Anti-roll bar linkage missing |5.3.3 |a| |ii|| | 1 |
| Offside Rear Anti-roll bar linkage insecurely attached |5.3.3 |a| |i|| | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting missing |5.3.3 |a| |ii|| | 1 |
| Nearside Front Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front brake caliper leaking |3.6.A.1| | 1 |
| Offside Rear Stop lamp not working |1.2.1b| | 1 |
| Offside Front Upper Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Rear Anti-roll bar synthetic bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar synthetic bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength o/s/r outer sill holed near (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill / floor area near (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill holed near (5.3.6 (a) (i)) | 1 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill / floor area near (5.3.6 (a) (i)) | 1 |
| Emissions not tested due to coolant leak and noise from belt area (8.2.2.2 (e)) | 1 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Nearside Front Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Headlamp not working on main beam |1.7.5a| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt drop link |2.4.G.2| | 1 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt drop link |2.4.G.2| | 1 |
| Nearside Headlamp adversely affected by the operation of another lamp |1.7.5c| | 1 |
| Offside Headlamp adversely affected by the operation of another lamp |1.7.5c| | 1 |
| Service brake: efficiency below requirements |3.7.C.1a| | 1 |
| Parking brake: efficiency below requirements |3.7.C.1b| | 1 |
| Rear Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced cill |7.1.1 |a| |i|| | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced arch |7.1.1 |a| |i|| | 1 |
| Nearside Headlamp not working on main beam |1.7.5a| | 1 |
| Offside Front Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Offside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar linkage which is adjustable, locking device insecure |2.4.G.1| | 1 |
| Headlamps matched pair incorrect colour |4.1.4 |a|| | 1 |
| Exhaust emissions exceed level of metered smoke for a turbo charged engine |8.2.2.2 |b|| | 1 |
| Nearside Front Battery insecure not secure correctly |1.9.1| | 1 |
| Rear Passenger`s seat insecure rear passenger seats fitted facing out rear of vehicle at time of test so seat belts will not operate correctly |6.2.A.1| | 1 |
| Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Steering damper leaking oil steering rack leaking oil |2.2.C.1f| | 1 |
| Rear Exhaust system not adequately supported back box missing |7.1.1| | 1 |
| Rear Exhaust has a major leak of exhaust gases back box missing |7.1.2| | 1 |
| Offside front brake binding |3.7.B.1| | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Rear Suspension arm attachment bracket/mounting fractured |2.4.G.1| | 1 |
| Offside Rear Rear reflector missing |1.5.1a| | 1 |
| Front All position lamps not working |1.1.A.3b| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded inner sill panel |2.4.A.3| | 1 |
| Windscreen washer not working | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength on inner lower sill |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength on inner lower sill |5.3.6 |a| |i|| | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting fractured |5.3.3 |b| |ii|| | 1 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt boot split |2.1.3 |g| |ii|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength on front cross member |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength on front cross member |5.3.6 |a| |i|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced on inner wheel arch |7.1.1 |a| |i|| | 1 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Central Rear Statutory seat belt missing Clasp. |5.1.1| | 1 |
| Offside Rear Statutory seat belt missing Rear most clasp. |5.1.1| | 1 |
| Central Rear Statutory seat belt missing Rear most clasp. |5.1.1| | 1 |
| Front brake excessively fluctuating | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Wheel arch. |2.4.A.3| | 1 |
| Offside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement D-bush. |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement D-bush. |2.4.G.2| | 1 |
| Nearside Front front brake binding |3.7.B.1| | 1 |
| Offside Front front brake binding |3.7.B.1| | 1 |
| Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Front All position lamps not working |1.1.A.3b| | 1 |
| Offside Front Service brake excessively binding |1.2.1 |f|| | 1 |
| Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Front Front position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Front Anti-roll bar ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Headlamp light intensity severely reduced poss a earthing fault (4.1.4 (a)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced and rear outer sill and inner sill/wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill and inner sill/wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced out riger to inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced out riger to inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Rear Rear fog lamp not working |1.3.2b| | 1 |
| Steering wheel in a condition that hampers proper control |2.1.1| | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Emissions not tested |7.0| | 1 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Lower Steering column universal joint has excessive play |2.1.5| | 1 |
| Nearside Inner Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Inner Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Fuel system component leaking |7.2.3| | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt droplink |2.4.G.2| | 1 |
| Offside Power steering component|s| leaking from a failed seal leaking from rack |2.3.3b| | 1 |
| Front Headlamp aim beam image obviously incorrect both sides |1.8.A.1b| | 1 |
| Front Headlamp not working on dipped beam both sides |1.7.5a| | 1 |
| Front Headlamp not working on main beam both sides |1.7.5a| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill and inner wing |2.4.A.3| | 1 |
| Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement both sides d bushes |2.4.G.2| | 1 |
| Front Anti-roll bar rubber bush deteriorated resulting in excessive movement both sides d bushes |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement drop link |2.4.G.2| | 1 |
| Nearside Front Suspension arm rubber bush deteriorated resulting in excessive movement rear bush |2.4.G.2| | 1 |
| Fuel system component leaking pump |7.2.3| | 1 |
| Nearside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Front Electrical wiring insecure under bonnet |1.9.2a| | 1 |
| Offside Front Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Front Tie bar/rod ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Tie bar/rod ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Rear Tie bar/rod has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Rear Outer Suspension spring mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Nearside Rear Inner Suspension spring mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
| Nearside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Outer Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Windscreen has damage | 1 |
| Front Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Nearside Front Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
| Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Horn sounds harsh or grating |1.6.2e| | 1 |
| Offside Front Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 1 |
| Nearside Front Upper Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Rear Anti-roll bar insecure |2.4.G.1| | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Outer Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Outer Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Inner Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Outer Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired inner sill not fully seam welded |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is inadequately repaired outer sill not fully seam welded |5.2.6| | 1 |
| Rear passenger door cannot be opened from outside the vehicle rear door/boot |6.2.B.1c| | 1 |
| Offside Rear Valve stem seriously damaged |4.1.D.1e| | 1 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill. (7.1.1 (a) (i)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Engine MIL inoperative or indicates a malfunction (8.2.2.2 (g)) | 1 |
| Horn not working (7.7 (a) (ii)) | 1 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Front Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 1 |
| Offside Front Brake pipe excessively damaged (1.1.11 (c)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Upper strut mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner wheel arch front of arch (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner wheel arch rear of arch (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner wheel arch front of arch (6.1.1 (c) (i)) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Shocker mounting (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Inner Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Front front brake juddering severely |3.7.A.2b| | 1 |
| Horn not working |7.7 |a| |ii|| | 1 |
| Rear Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Steering column universal joint insecure |2.1.5| | 1 |
| Offside Lower Ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Front Power steering pipe|s| or hose|s| leaking from a joint |2.3.3b| | 1 |
| Fuel system component leaking pump area |7.2.3| | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Front Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Front Anti-roll bar pin or bush excessively worn D bush |5.3.4 |a| |i|| | 1 |
| Nearside Rear Oil leaking excessively from transmission Axle |8.4.1 |a| |i|| | 1 |
| Nearside Rear Parking brake inoperative on one side Possibly contaminated |1.4.1 |a|| | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch corroded (7.1.1 (a) (i)) | 1 |
| Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced inner wheel arch corroded (7.1.1 (a) (i)) | 1 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
| Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Rear Stop lamp not working |1.2.1b| | 1 |
| Nearside Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Fuel system component leaking Fuel pump |7.2.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Inner wheel arch |2.4.A.3| | 1 |
| Nearside Battery insecure |1.9.1| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded sill end |2.4.A.3| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Arch (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Whole sill plus end (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Whole sill plus end (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Arch/chassis (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Arch/chassis (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area fractured significantly reducing structural strength Arch/chassis cracked (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis/ spring mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis/ spring mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Front cross member (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Front cross member (5.3.6 (a) (i)) | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Headlamp light intensity severely reduced Main (4.1.4 (a)) | 1 |
| Offside Headlamp light intensity severely reduced Main (4.1.4 (a)) | 1 |
| Offside Dipswitch operation does not deflect all main beam headlamps to make them dipped beams (4.1.3 (b)) | 1 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Offside Rear Anti-roll bar linkage damaged and seriously weakened (5.3.3 (b) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Emissions not tested Coolant leak/overheating (8.2.2.2 (e)) | 1 |
| Nearside Rear Upper Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Upper Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Fuel cap/sealing device sealing washer missing |7.2.4c| | 1 |
| Stop lamp not working |1.2.1b| | 1 |
| Fuel system component leaking Suspect pump |7.2.3| | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting nut missing |2.4.G.1| | 1 |
| Offside Front Upper Anti-roll bar linkage fractured |2.4.G.1| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement roll bar d bush |2.4.G.2| | 1 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill corroded |6.1.B.2| | 1 |
| Nearside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill corroded |6.1.B.2| | 1 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside front brake binding |3.7.B.1| | 1 |
| Nearside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Front Power steering ram|s| leaking from a failed component |2.3.3b| | 1 |
| Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Headlamp has a product on the light source so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Rear Rear fog lamp missing |1.3.2a| | 1 |
| Rear Anti-roll bar linkage pin or bush excessively worn ( D ) (5.3.4 (a) (i)) | 1 |
| Front Anti-roll bar linkage pin or bush excessively worn ( D ) (5.3.4 (a) (i)) | 1 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Position lamp not working |4.2.1 |a|| | 1 |
| Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Nearside Front Steering rack gaiter split |2.2.D.2d| | 1 |
| An item not tested |Manual| | 1 |
| Offside Rear Anti-roll bar linkage damaged and seriously weakened |2.4.G.1| | 1 |
| Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 1 |
| Power steering component leaking |2.1.5 |a|| | 1 |
| Nearside Rear Seat belt missing |7.1.2 |a|| | 1 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Headlamp aim not tested (4.1.2 (b)) | 1 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Brake insecure Carrier (1.1.21 (c)) | 1 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Front Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Fuel cap/sealing device missing |7.2.4a| | 1 |
| Offside Rear Anti-roll bar linkage insecure broken |2.4.G.1| | 1 |
| Front brake disc excessively scored |3.5.1h| | 1 |
| Nearside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Rear Seat belt not functioning as intended os & ns (7.1.2 (c)) | 1 |
| Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Nearside Front Brake hose twisted |3.6.B.4c| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Central Exhaust has a major leak of exhaust gases flexi |7.1.2| | 1 |
| Nearside Suspension arm rubber bush deteriorated resulting in excessive movement back bush |2.4.G.2| | 1 |
| Nearside Side repeater not working |1.4.A.2c| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Inner sill panel |2.4.A.3| | 1 |
| Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 1 |
| Offside Rear Anti-roll bar has excessive play in a pin/bush braket fractured |2.4.G.2| | 1 |
| Anti-lock braking system warning lamp indicates an ABS fault | 1 |
| Nearside Rear Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Front Anti-roll bar fractured |2.4.G.1| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Nearside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Towbar fractured seriously affecting its strength within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
| Offside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Vehicle structure is deformed and structural rigidity is significantly reduced Sill (6.1.1 (a) (i)) | 1 |
| Nearside Front Inner Vehicle structure is deformed and structural rigidity is significantly reduced Sill (6.1.1 (a) (i)) | 1 |
| Central Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Trailer electrical socket likely to become detached (4.10 (a) (ii)) | 1 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member |5.3.6 |a| |i|| | 1 |
| Offside Front Lower Suspension arm ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Emissions not tested due to excessive coolant leak |7.4.B.1| | 1 |
| Headlamp aim not tested |1.8.A.1c| | 1 |
| Headlamp not working on dipped beam both |1.7.5a| | 1 |
| Headlamp not working on main beam both |1.7.5a| | 1 |
| Nearside Rear Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| All position lamps not working |1.1.A.3b| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Offside Rear Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Front brake application uneven | 1 |
| Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Rear fog lamp switch insecure |1.3.1a| | 1 |
| Nearside Passenger`s seat insecure |6.2.A.1| | 1 |
| Rear Statutory seat belt missing |5.1.1| | 1 |
| Nearside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Inner Rear Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Inner Rear Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar linkage worn and seriously weakened |2.4.G.1| | 1 |
| Offside Statutory seat belt missing |5.1.1| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Centre Stop lamp not working |1.2.1b| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |