| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 16 |
| Horn not working (7.7 (a)) | 7 |
| Headlamp aim out of alignment | 6 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 5 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 5 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 4 |
| Registration plate lamp issues | 4 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 4 |
| Nearside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 4 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 4 |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 3 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 3 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 3 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 3 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 2 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
| Offside Front Suspension arm corroded and seriously weakened (5.3.3 (b) (i)) | 2 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 2 |
| Brake pipe excessively corroded | 2 |
| Brakes imbalanced across an axle | 2 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Offside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 2 |
| Central Front Exhaust emissions exceed default limit of 1.5m-1 (8.2.2.2 (b)) | 2 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 2 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 2 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 2 |
| Anti-lock braking system warning lamp indicates an ABS fault | 2 |
| Nearside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 2 |
| Offside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 2 |
| Offside Front Shock absorbers has a serious fluid leak | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 2 |
| Rear fog lamp switch inoperative (4.5.3 (a)) | 2 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 2 |
| Emissions unable to be completed (8.2.2.2 (e)) | 2 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 2 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 2 |
| Offside Headlamp not working on main beam |1.7.5a| | 2 |
| Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Front Outer Drive shaft joint excessively worn (6.1.7 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sills (6.1.1 (c) (i)) | 1 |
| Nearside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Cross member (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Cross member (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced within area of lower suspension arm mount (6.1.1 (c) (i)) | 1 |
| Offside Rear Seat belt missing stalk (7.1.2 (a)) | 1 |
| Seat belt missing center rear (7.1.2 (a)) | 1 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Windscreen washer not working | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Front Prop shaft joint constant velocity boot no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Rear Passengers seat insecure (6.2.6 (a) (ii)) | 1 |
| Headlamp aim unable to be tested (4.1.2 (b)) | 1 |
| Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Steering rack has excessive free play detected at the steering wheel (steering rack fitted) (2.3 (a) (i)) | 1 |
| Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt Both (6.1.7 (g) (ii)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sil (5.3.6 (a) (i)) | 1 |
| Front Service brake excessively binding Both (1.2.1 (f)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Centre sill to pillar holed corroded (6.2.2 (d) (i)) | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill holed and corroded (6.1.1 (c) (i)) | 1 |
| Nearside Front Battery insecure and likely to fall from carrier clamp not tight ??? (4.13 (a) (ii)) | 1 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill to pillar holed and corroded (6.2.2 (d) (i)) | 1 |
| Nearside Front Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill top holed and corroded (6.2.2 (d) (i)) | 1 |
| Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction (3.1 (a) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Rear Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 1 |
| Nearside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Offside Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Offside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting front cross member (6.2.2 (d) (i)) | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Shock absorbers has a serious fluid leak | 1 |
| Offside Rear Hydraulic fluid leaking excessively wheel (8.4.1 (a) (i)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect Both o/s/f and n/s/f (4.1.2 (c)) | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn "D" Bush. (5.3.4 (a) (i)) | 1 |
| Offside Front Anti-roll bar pin or bush excessively worn "D" Bush. (5.3.4 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Central Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Stop lamp(s) not working trailer (4.3.1 (a) (ii)) | 1 |
| Offside Stop lamp(s) not working trailer (4.3.1 (a) (ii)) | 1 |
| Nearside Front Outer Prop shaft joint constant velocity boot no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Front Outer Prop shaft joint constant velocity boot no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Corrosion hole in rear crossmember adjacent to tow bar mounting (6.1.1 (c) (i)) | 1 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Speedometer cannot be illuminated (7.8 (c) (ii)) | 1 |
| All direction indicators not working (4.4.1 (a) (ii)) | 1 |
| Hazard warning lamps inoperative (4.4.1 (e)) | 1 |
| Position lamp not working ALL position lamps inoperative (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Inner Anti-roll bar attachment bracket/mounting fractured (5.3.3 (b) (ii)) | 1 |
| Rear Anti-roll bar linkage pin or bush excessively worn All rear anti roll bar bushes excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Rear fog lamp light intensity significantly reduced (4.5.4 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger /chasiss (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Headlamp aim not tested (4.1.2 (b)) | 1 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill inner and outer (6.2.2 (d) (i)) | 1 |
| Stop lamp(s) all not working not working all the time , sometimes they work sometimes not (4.3.1 (a) (iii)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill inner and outer (6.2.2 (d) (i)) | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting fractured bracket snapped, also deformed (5.3.3 (b) (ii)) | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting missing bush missing (5.3.3 (a) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill holed (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill holed (6.1.1 (c) (i)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill/wheel arch holed (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength INNER WHEEL ARCH (5.3.6 (a) (i)) | 1 |
| Stop lamp(s) switch with a delay in operation (4.3.2 (a) (ii)) | 1 |
| Nearside Front Anti-roll bar pin or bush excessively worn D-Bush. (5.3.4 (a) (i)) | 1 |
| Offside Front Anti-roll bar pin or bush excessively worn D-Bush. (5.3.4 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn D-Bush. (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn D-Bush. (5.3.4 (a) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Multiples Places Of Outer Sill Marked With Yellow Chalk. (6.1.1 (c) (i)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Multiples Places Of Outer Sill Marked With Yellow Chalk. (6.1.1 (c) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner arch (6.2.2 (d) (i)) | 1 |
| Nearside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting 2 inner sill (6.2.2 (d) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting by inner sill (6.2.2 (d) (i)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member under radiator (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill near rear suspension mounting (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill near rear suspension mounting (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under wing 2 places (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Offside Fuel cap/sealing device ineffective temporary cap fitted, push type (6.1.3 (b) (i)) | 1 |
| Nearside Front Lower Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill area (6.1.1 (c) (i)) | 1 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Suspension arm pin or bush excessively worn Rear bush (5.3.4 (a) (i)) | 1 |
| Front passenger door cannot be opened from inside the vehicle (6.2.3 (a)) | 1 |
| Offside Side repeater light intensity significantly reduced (4.4.3 (a)) | 1 |
| Nearside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
| Offside Front Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |
| Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 1 |
| Rear Seat belt missing (7.1.2 (a)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength closing panel (5.3.6 (a) (i)) | 1 |
| Nearside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Front Service brake imbalanced across an axle (1.2.1 (b) (i)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Anti-roll bar linkage pin or bush likely to become detached (5.3.4 (a) (ii)) | 1 |
| Offside Front Anti-roll bar linkage insecurely attached (5.3.3 (a) (i)) | 1 |
| Rear fog lamp likely to become detached (4.5.1 (c) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Brake performance unable to be tested (1.2.1 (g)) | 1 |
| Nearside Front Subframe mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
| Offside Rear Subframe mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength in wheel arch (5.3.6 (a) (i)) | 1 |
| Emissions unable to be completed (8.2.1.2 (d)) | 1 |
| Offside Front Sub-frame corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Offside Front Brake hose leaking on a hydraulic braking system (1.1.12 (c) (ii)) | 1 |
| Offside Front Subframe mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area is inadequately repaired (7.1.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Brake disc contaminated (1.1.14 (b)) | 1 |
| Exhaust emissions exceed level of metered smoke for a turbo charged engine (8.2.2.2 (b)) | 1 |
| Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Front Headlamp not working on dipped beam When main beam is switched on (4.1.1 (a) (ii)) | 1 |
| Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Exhaust has a major leak of exhaust gases centre section (6.1.2 (a)) | 1 |
| Rear Service brake excessively binding both (1.2.1 (f)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CROSS MEMBER (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength WHEEL BOX TOWARDS REAR (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength WHEEL BOX TOWARDS FRONT (5.3.6 (a) (i)) | 1 |
| Offside Front Brake prescribed area is excessively corroded inner arch (1.1.21 (e) (i)) | 1 |
| Offside Front Brake prescribed area is excessively corroded Inner arch (1.1.21 (e) (i)) | 1 |
| Offside Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting outer sill (6.2.2 (d) (i)) | 1 |
| Offside Stop lamp not working |1.2.1b| | 1 |
| Offside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sills |5.3.6 |a| |i|| | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength crossmember |5.3.6 |a| |i|| | 1 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Exhaust has a major leak of exhaust gases centre silencer (6.1.2 (a)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected front trailing arm mount (5.3.6 (a) (ii)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt insecure (2.1.3 (g) (ii)) | 1 |
| Offside Undertray likely to become detached rear mounting (6.2.1 (a) (ii)) | 1 |
| Offside Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded cross member |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Rear fog lamp not working |1.3.2b| | 1 |
| Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement D bush |2.4.G.2| | 1 |
| Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Nearside Front Valve stem seriously damaged |4.1.D.1e| | 1 |
| Offside Front Valve stem seriously damaged |4.1.D.1e| | 1 |
| Nearside Rear Valve stem seriously damaged |4.1.D.1e| | 1 |
| Offside Rear Valve stem seriously damaged |4.1.D.1e| | 1 |
| Offside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Headlamp not working on main beam |1.7.5a| | 1 |
| Rear Exhaust has a major leak of exhaust gases silencer |7.1.2| | 1 |
| Nearside Battery insecure |1.9.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Nearside Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Rear fog lamp missing |1.3.2a| | 1 |
| Rear fog lamp tell tale missing |1.3.1b| | 1 |
| Rear fog lamp switch missing |1.3.1a| | 1 |
| Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.2.1 (b)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill corroded within 30 cm of spring mounting (5.3.6 (a) (i)) | 1 |
| Nearside Front Passengers seat insecure (6.2.6 (a) (ii)) | 1 |
| Parking brake lever defective so that it cannot be satisfactorily operated bolts loose and lever insecure (1.1.6 (d)) | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |