| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 33 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 20 |
| Windscreen washer not working | 10 |
| Headlamp aim out of alignment | 9 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 8 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 8 |
| Offside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 7 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 6 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 6 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 6 |
| Registration plate lamp issues | 6 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 5 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 5 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 5 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 5 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 5 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 4 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 4 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 4 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 4 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 4 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 4 |
| Brake pipe excessively corroded | 4 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 4 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 4 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 4 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 4 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 3 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 3 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 3 |
| Nearside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 3 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 3 |
| Offside Front Shock absorbers has a serious fluid leak | 3 |
| Exhaust emissions test not completed because smoke levels are significantly in excess of the specified limit values (8.2.2.2 (f)) | 3 |
| Fuel system component leaking (6.1.3 (b) (i)) | 3 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 3 |
| Exhaust emits excessive smoke or vapour likely to obscure the vision of other road users (8.2.2.2 (c)) | 3 |
| Horn not working (7.7 (a)) | 3 |
| Rear Bumper insecure (6.1.4 (a) (i)) | 3 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Nearside Rear Bumper insecure (6.1.4 (a) (i)) | 3 |
| Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 3 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 3 |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 3 |
| Nearside Front Shock absorbers has a serious fluid leak | 3 |
| Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 3 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 3 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 3 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 2 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 2 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 2 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Nearside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 2 |
| Nearside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 2 |
| Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced crossmember (6.1.1 (c) (i)) | 2 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced corner panel behind bumper (6.1.1 (c) (i)) | 2 |
| Offside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 2 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Offside Front Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Rear Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 2 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 2 |
| Offside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 2 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Power steering component leaking (2.1.5 (a)) | 2 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch (5.3.6 (a) (i)) | 2 |
| Offside Stop lamp not working |1.2.1b| | 2 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Rear fog lamp tell-tale not working (4.9.1 (a) (ii)) | 2 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 2 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
| Exhaust emissions exceed level of metered smoke for a turbo charged engine (8.2.2.2 (b)) | 2 |
| Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 2 |
| Offside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 2 |
| Lower Steering column universal joint has excessive wear or play (2.2.2 (c)) | 2 |
| Parking brake lever has no reserve travel (3.1.6b) | 2 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 2 |
| Offside Headlamp has a product on the lens so that the light output is severely reduced (4.1.4 (b)) | 2 |
| Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 2 |
| Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 2 |
| Power steering pipe/hose leaking (2.1.5 (a)) | 2 |
| Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 2 |
| Emissions not tested (8.2.2.2 (e)) | 2 |
| Headlamp aim not tested (4.1.2 (b)) | 2 |
| Front brake disc in such a condition that it is seriously weakened | 2 |
| Rear brake disc in such a condition that it is seriously weakened | 2 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength crossmember 30cm subframemount (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength subframe 30cm of mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis fixing (6.1.1 (c) (i)) | 1 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively damaged significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced x member (6.1.1 (c) (i)) | 1 |
| Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis (6.1.1 (c) (i)) | 1 |
| Nearside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar linkage pin or bush likely to become detached (5.3.4 (a) (ii)) | 1 |
| Electrical wiring insecure and connectors likely to become disconnected battery wiring (4.11 (a) (ii)) | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced door sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced door sill (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced front cross member (6.1.1 (c) (i)) | 1 |
| Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced front to rear sill (6.1.1 (c) (i)) | 1 |
| Rear Anti-roll bar pin or bush excessively worn D bushes x2 (5.3.4 (a) (i)) | 1 |
| Nearside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced front to rear sill (6.1.1 (c) (i)) | 1 |
| Nearside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill front to rear (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced wheel arch (6.1.1 (c) (i)) | 1 |
| Front Headlamp aim projected beam image is obviously incorrect Both (4.1.2 (c)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
| Service brake excessively fluctuating both front (1.2.1 (e)) | 1 |
| Rear fog lamp does not face the rear (4.5.4 (a)) | 1 |
| Nearside Rear Vehicle structure excessively corroded within 30cm of towbar mounting rear crossmember (6.1.6 (i) (i)) | 1 |
| Nearside Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength CHASSIS (5.3.6 (a) (i)) | 1 |
| Nearside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced crossmember (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced crossmember (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced arch (6.1.1 (c) (i)) | 1 |
| Nearside Rear Other passenger door cannot be opened from outside the vehicle (6.2.3 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Macpherson strut attachment bracket/mounting insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Crossmember has small hole (5.3.6 (a) (i)) | 1 |
| Offside Track rod end ball joint dust cover insecure so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Upper spring mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Spring mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength To rear of wheel arch and side of strut top mount (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Around rear of wheel arch, next to upper strut top mount and inner chassis leg (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Chassis behind upper spring mount (5.3.6 (a) (i)) | 1 |
| Power steering component leaking Steering rack (2.1.5 (a)) | 1 |
| Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Other passenger door cannot be opened from outside the vehicle side sliding door (6.2.3 (a)) | 1 |
| Rear fog lamp switch inoperative (4.5.3 (a)) | 1 |
| Offside Headlamp aim unable to be tested (4.1.2 (b)) | 1 |
| Nearside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Nearside sill at rear, corrosion both inner and outer (5.3.6 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar pin or bush likely to become detached D bush bracket broken and open (5.3.4 (a) (ii)) | 1 |
| Nearside Vehicle structure excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
| Power steering component leaking Rack (2.1.5 (a)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Heavy corrosion within 30cm (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Subframe mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases flexi (6.1.2 (a)) | 1 |
| Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt both sides (6.1.7 (g) (ii)) | 1 |
| Offside Rear Body panel corroded and likely to cause injury wheel arch (6.2.1 (a) (i)) | 1 |
| Central Exhaust has a major leak of exhaust gases Flexible section (6.1.2 (a)) | 1 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting o/s rear chassis to sill (6.2.2 (d) (i)) | 1 |
| Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting o/s rear chassis to shocker (6.2.2 (d) (i)) | 1 |
| Power steering component leaking steering rack (2.1.5 (a)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength near shock top mount (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 1 |
| Offside Front Bumper insecure (6.1.4 (a) (i)) | 1 |
| Nearside Front Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill area (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch inner and outer (5.3.6 (a) (i)) | 1 |
| Rear Vehicle structure excessively corroded within 30cm of towbar mounting inner lower quater areas both sides (6.1.6 (i) (i)) | 1 |
| Rear Rear fog lamp lens defective such that emitted light is adversely affected (4.5.1 (b) (ii)) | 1 |
| Offside Front Headlamp light intensity severely reduced dipped and main beam (4.1.4 (a)) | 1 |
| Power steering inoperative (2.1.5 (c) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength suspension arm rear bush mounting area (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength arch several places (5.3.6 (a) (i)) | 1 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill several places (5.3.6 (a) (i)) | 1 |
| Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill several places (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength out rigger (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor (5.3.6 (a) (i)) | 1 |
| Front Steering component mounting prescribed area is excessively corroded slam panel/ radiator mount (2.1.2 (e) (i)) | 1 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Headlamp light intensity severely reduced x2 (4.1.4 (a)) | 1 |
| Power steering component leaking rack !!!!!!!!! (2.1.5 (a)) | 1 |
| Steering rack gaiter missing or no longer prevents the ingress of dirt x2 (2.1.3 (g) (ii)) | 1 |
| Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting n/s and o/s inner sills (6.2.2 (d) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Front Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Sill next to outrigger. |6.1.B.2| | 1 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Central Rear Seat belt damaged sufficient to significantly weakened the webbing |5.2.2a| | 1 |
| Offside Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Offside Rear Inner Seat belt anchorage prescribed area is excessively corroded wheel arch |5.2.6| | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded sill x2 |5.2.6| | 1 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Emissions not tested |7.0| | 1 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Rear fog lamp not working |1.3.2b| | 1 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Headlamp not working on main beam |1.7.5a| | 1 |
| Offside Headlamp not working on main beam |1.7.5a| | 1 |
| Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Cross member corroded (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Arch corroded marked yellow (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Arch VERY corroded marked yellow (6.1.1 (c) (i)) | 1 |
| Nearside Exhaust has a major leak of exhaust gases Marked yellow (6.1.2 (a)) | 1 |
| Emissions unable to be completed exhaust blow (8.2.2.2 (e)) | 1 |
| Nearside Rear Position lamp showing white light to the rear (4.2.3 (a) (ii)) | 1 |
| Nearside Front Upper Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner Arch (6.1.1 (c) (i)) | 1 |
| Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill x2 (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Crossmember (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Crossmember (6.1.1 (c) (i)) | 1 |
| Nearside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill /strengthen plate (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength x2 (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill x3 (5.3.6 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member inner panel both sides (5.3.6 (a) (i)) | 1 |
| Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength cross member (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength under sill pane (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength main chassis (5.3.6 (a) (i)) | 1 |
| Nearside Rear Vehicle structure has excessive damage seriously affecting its strength within 30cm of a towbar mounting (6.1.6 (i) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength shocker mounting (5.3.6 (a) (i)) | 1 |
| Front Electrical wiring insecure and in contact with sharp edges to lights (4.11 (a) (ii)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill chalked (5.3.6 (a) (i)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill chalked (7.1.1 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch chalked (5.3.6 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chalked (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength chalked (5.3.6 (a) (i)) | 1 |
| Brakes imbalanced across an axle | 1 |
| Offside Rear Service brake lagging in operation (1.2.1 (d)) | 1 |
| Nearside Battery insecure and likely to cause a short circuit Battery tray heavily corroded and and insecure against body (4.13 (a) (ii)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill,chalked (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Sill,chalked (5.3.6 (a) (i)) | 1 |
| Brake disc contaminated All 4 discs heavily corroded (1.1.14 (b)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is inadequately repaired (5.3.6 (a) (i)) | 1 |
| Offside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Body component damaged and likely to cause injury rear steps bolts excessive length (6.2.1 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength box section (5.3.6 (a) (i)) | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sall (6.1.1 (c) (i)) | 1 |
| Offside Rear Integral body structure inadequately repaired such that structural rigidity is significantly reduced inner sill (6.1.1 (d) (i)) | 1 |
| Offside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch to sill end (6.1.1 (c) (i)) | 1 |
| Nearside Front Outer Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Front Outer Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt boot insecure (5.3.4 (b) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member (5.3.6 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Offside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt upper and lower (5.3.4 (b) (ii)) | 1 |
| Offside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Offside Rear Passengers seat insecure rearmost (6.2.6 (a) (ii)) | 1 |
| Nearside Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced excessively corroded/holed in 2 places (6.1.1 (c) (i)) | 1 |
| Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outrigger (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outrigger (6.1.1 (c) (i)) | 1 |
| Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt split (6.1.7 (g) (ii)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
| Offside Rear Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outer sill (6.2.2 (d) (i)) | 1 |
| Nearside Front Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Inner sill (6.2.2 (d) (i)) | 1 |
| Windscreen damaged and affecting the drivers view of the road (3.2 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill front and rear (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill front and rear end (5.3.6 (a) (i)) | 1 |
| Offside Front Brake hose leaking on a hydraulic braking system hose seal on caliper (1.1.12 (c) (ii)) | 1 |
| Emissions not tested exhaust blow (8.2.2.2 (e)) | 1 |
| Fuel system component leaking diesel leak. fuel pump area? (6.1.3 (b) (i)) | 1 |
| Offside Rear Rear fog lamp not working lamp in poor condition and requires replacement (4.5.1 (a) (ii)) | 1 |
| Nearside Front Lower Suspension arm pin or bush excessively worn Rear Bush (5.3.4 (a) (i)) | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis rail over axle (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger beside trailing arm mounting bracket (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sills (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a) | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting damaged and its strength is seriously reduced (2.4.G.1) | 1 |
| Centre Exhaust has a major leak of exhaust gases (7.1.2) | 1 |
| Rear fog lamp not working (1.3.2b) | 1 |
| Anti-roll bar rubber bush deteriorated resulting in excessive movement (2.4.G.2) | 1 |
| Nearside Front position lamp(s) not working (1.1.A.3b) | 1 |
| Nearside Stop lamp not working (1.2.1b) | 1 |
| Offside Rear fog lamp not working (1.3.2b) | 1 |
| Nearside Headlamp aim beam image obviously incorrect (1.8.A.1b) | 1 |
| Nearside Front Suspension arm rubber bush deteriorated resulting in excessive movement (2.4.G.2) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Front Power steering component(s) leaking Steering rack (2.3.3b) | 1 |
| Offside Front Suspension arm rubber bush deteriorated resulting in excessive movement Front bush (2.4.G.2) | 1 |
| Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement Off side and near side (2.4.G.2) | 1 |
| Offside Rear Body has a sharp edge caused by damage Tail gate (6.1.C.1) | 1 |
| Offside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement (2.4.G.2) | 1 |
| Anti-lock braking system warning lamp indicates an ABS fault | 1 |
| Offside Rear Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced panel (6.1.1 (c) (i)) | 1 |
| Position lamp not working All (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn D rubber (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn D rubber (5.3.4 (a) (i)) | 1 |
| Nearside Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Nearside Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Offside Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Headlamp aim projected beam image is obviously incorrect both lamps (4.1.2 (c)) | 1 |
| Power steering component leaking rack assembly (2.1.5 (a)) | 1 |
| Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Registration plate issues | 1 |
| Headlamp aim unable to be tested (4.1.2 (b)) | 1 |
| Front Anti-roll bar pin or bush excessively worn D Bushes (5.3.4 (a) (i)) | 1 |
| Power steering component leaking rack (2.1.5 (a)) | 1 |
| Offside Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 1 |
| Offside Front Passengers seat insecure (6.2.6 (a) (ii)) | 1 |
| Offside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
| Offside Front Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
| Nearside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Fuel system component leaking pump (6.1.3 (b) (i)) | 1 |
| Brake performance not tested (1.2.1 (g)) | 1 |
| Brake performance not tested parking brake (1.2.1 (g)) | 1 |
| Emissions not tested Exhaust broken, can not insert DSM (8.2.2.2 (e)) | 1 |
| Nearside Stop lamp(s) lens defective such that the emitted light is adversely affected (4.3.1 (b) (ii)) | 1 |
| Nearside Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting fractured (5.3.3 (b) (ii)) | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect (1.8.A.1b) | 1 |
| Offside Front Headlamp aim beam image obviously incorrect (1.8.A.1b) | 1 |
| Nearside Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a) | 1 |
| Offside Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc (2.5.C.1a) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded cross member (2.4.A.3) | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded cross member (2.4.A.3) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area is excessively corroded sill (2.4.A.3) | 1 |
| Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.2.C.1c) | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering Inner sill (6.1.A.1) | 1 |
| Offside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement D bush (2.4.G.2) | 1 |
| Offside Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Nearside Front Upper Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt (2.4.G.2) | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded (2.4.A.3) | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting fractured (2.4.G.1) | 1 |
| Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement (2.4.G.2) | 1 |
| Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush (2.4.G.2) | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings (6.1.B.2) | 1 |
| Exhaust emits excessive smoke or vapour of any colour (7.4.B.4) | 1 |
| Emissions not tested (7.0) | 1 |
| Brake performance not tested (3.7.A.1) | 1 |
| Service brake: efficiency below requirements (3.7.C.1a) | 1 |
| Parking brake: efficiency below requirements (3.7.C.1b) | 1 |
| Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner/outer sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Steering locking device missing track rod (2.1.3 (d)) | 1 |
| Nearside Front Outer Suspension component mounting prescribed area fractured significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area fractured significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area fractured significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area fractured significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Outer Suspension component mounting prescribed area fractured significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area fractured significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area fractured significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area fractured significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Road wheel more than one fixing missing (5.2.1 (a) (ii)) | 1 |
| Nearside Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Offside Seat belt not functioning as intended incorrectly fitted (7.1.2 (c)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill holed x2 (5.3.6 (a) (i)) | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength crossmember holed x2 holes (5.3.6 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced OUTER SILL (7.1.1 (a) (i)) | 1 |
| Emissions unable to be completed engine water leak (8.2.2.2 (e)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced OUTER SILL (7.1.1 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Offside Rear Anti-roll bar linkage ball joint likely to become detached (5.3.4 (a) (ii)) | 1 |
| Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced cross member (6.1.1 (c) (i)) | 1 |
| Offside Rear Bumper insecure wing corroded (6.1.4 (a) (i)) | 1 |
| Nearside Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Offside Front Direction indicator obviously incorrectly positioned (4.4.3 (a)) | 1 |
| Nearside Front Suspension arm pin or bush excessively worn rear bush (5.3.4 (a) (i)) | 1 |
| Offside Rear Rear reflector defective or damaged by more than 50% of the reflecting surface lamp (4.8.1 (a) (ii)) | 1 |
| Front Bumper insecure (6.1.4 (a) (i)) | 1 |
| Nearside Rear Body panel corroded and likely to cause injury WHEEL ARCH (6.2.1 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Front Vehicle structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired cross member (6.2.2 (d) (ii)) | 1 |
| Battery insecure and likely to fall from carrier X 2 (4.13 (a) (ii)) | 1 |
| Nearside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Front Position lamp not working both sides (4.2.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner and outer sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner and outer sill (5.3.6 (a) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Nearside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced center sill (6.1.1 (c) (i)) | 1 |
| Rear Vehicle structure excessively corroded within 30cm of towbar mounting both sides (6.1.6 (i) (i)) | 1 |
| Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Rear Anti-roll bar rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Front Steering component excessively corroded and unserviceable |2.2.C.1d| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
| Nearside Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Nearside Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Offside Rear fog lamp not working |1.3.2b| | 1 |
| Nearside Rear brake disc contaminated by oil |3.5.1h| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded out rigger by front sub frame mount |2.4.A.3| | 1 |
| Nearside Stop lamp not working |1.2.1b| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassis outrigger |2.4.A.3| | 1 |
| Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Front Outer Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Inner Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Inner Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Inner Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Lower Suspension arm pin or bush excessively worn rear bush (5.3.4 (a) (i)) | 1 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively damaged significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill has a large hole (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Rear Seat belt missing (7.1.2 (a)) | 1 |
| Rear Passengers seat backrest cannot be secured in the upright position. (6.2.6 (a) (i)) | 1 |
| Offside Outer Integral body structure inadequately repaired such that structural rigidity is significantly reduced sill not welded (6.1.1 (d) (i)) | 1 |
| Offside Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill holed and corroded (6.1.1 (c) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
| Nearside Rear Suspension spring mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill and under sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill and under sill (5.3.6 (a) (i)) | 1 |
| Windscreen in such a condition that visibility through swept area is seriously affected (3.2 (c) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill / lower inner wheel arch (5.3.6 (a) (i)) | 1 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |