Most common failures | No# failures |
---|
Windscreen wiper does not clear the windscreen effectively | 16 |
Registration plate lamp issues | 5 |
Offside Rear fog lamp not working |1.3.2b| | 4 |
Brake pipe excessively corroded | 4 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 3 |
Offside Rear Stop lamp not working |1.2.1b| | 2 |
Rear Rear fog lamp not working |1.3.2b| | 2 |
Nearside Rear Stop lamp not working |1.2.1b| | 2 |
Offside Front Front position lamp|s| not working |1.1.A.3b| | 2 |
Nearside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Offside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 2 |
Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Rear fog lamp tell tale not working |1.3.1b| | 2 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
Brakes imbalanced across an axle | 2 |
Nearside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
Offside Front position lamp|s| not working |1.1.A.3b| | 2 |
Anti-lock braking system warning lamp indicates an ABS fault | 2 |
Offside Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Rear fog lamp insecure |1.3.2a| | 1 |
Offside Rear Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
Rear Service brake excessively binding (1.2.1 (f)) | 1 |
Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 1 |
Offside Rear Rear fog lamp missing |1.3.2a| | 1 |
rear parking |secondary| brakes imbalanced | 1 |
Rear parking brake recording little or no effort | 1 |
Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Emissions not tested |7.0| | 1 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
Offside Rear Parking (secondary brake) on a single line braking system has inadequate effort at a wheel (1.3.1 (a) (i)) | 1 |
Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
Nearside Rear fog lamp not working |1.3.2b| | 1 |
Offside Rear fog lamp does not face the rear |1.3.2a| | 1 |
Offside Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
Nearside Rear Towbar component excessively corroded |6.6.1| | 1 |
Offside Rear Towbar component excessively corroded |6.6.1| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Registration plate issues | 1 |
Offside Rear Anti-roll bar attachment bracket/mounting damaged and its strength is seriously reduced |2.4.G.1| | 1 |
Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings centre outer sil |6.1.B.2| | 1 |
Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings centre outer sil |6.1.B.2| | 1 |
Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Offside Inner Rear position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Front Passenger`s seat insecure |6.2.A.1| | 1 |
Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
Rear fog lamp switch missing |1.3.1a| | 1 |
Battery insecure |1.9.1| | 1 |
Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |
Nearside Rear Wheel nut|s| loose |4.2.A.1e| | 1 |
Nearside Rear Wheel nut|s| missing |4.2.A.1e| | 1 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
Nearside Headlamp not working on main beam |1.7.5a| | 1 |
Nearside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Offside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Offside Outer Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 1 |
Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength centre outer sill |5.3.6 |a| |i|| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 1 |
Nearside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength centre outer sill |5.3.6 |a| |i|| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 1 |
Offside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 1 |
Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch |5.3.6 |a| |i|| | 1 |
Nearside Rear Lower Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 1 |
Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross support |5.3.6 |a| |i|| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg |5.3.6 |a| |i|| | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg |5.3.6 |a| |i|| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill x3 |5.3.6 |a| |i|| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill x3 |5.3.6 |a| |i|| | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing |5.3.6 |a| |i|| | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing x2 |5.3.6 |a| |i|| | 1 |
Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
Offside Front Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Central Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Exhaust system not adequately supported middle box hanger snapped |7.1.1| | 1 |
Nearside Rear Anti-roll bar linkage pin or bush excessively worn D BUSH (5.3.4 (a) (i)) | 1 |
Offside Rear Anti-roll bar linkage pin or bush excessively worn D BUSH (5.3.4 (a) (i)) | 1 |
Offside Rear Anti-roll bar linkage pin or bush excessively worn LOWER BUSH (5.3.4 (a) (i)) | 1 |
Offside Rear Rear fog lamp switch inoperative (4.5.3 (a) (ii)) | 1 |
Offside Rear fog lamp emits a light other than red |1.3.2e| | 1 |
Rear fog lamp does not emit a steady red light |1.3.2e| | 1 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Nearside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
Rear Exhaust has a major leak of exhaust gases x2 holes |7.1.2| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
Nearside Rear Seat belt anchorage prescribed area is excessively corroded outer wheel arch |5.2.6| | 1 |
Horn not working (7.7 (a) (ii)) | 1 |
Nearside Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 1 |
Offside Headlamp has a product on the light source so that the light output is severely reduced (4.1.4 (b)) | 1 |
Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Offside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
Centre Rear Upper Stop lamp not working |1.2.1b| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded trailing arm mount outer sill |2.4.A.3| | 1 |
Offside Front Lower Suspension component mounting prescribed area is excessively corroded arm rear mount inner sill |2.4.A.3| | 1 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
Rear rear parking |secondary| brake grabbing severely |3.7.B.6b| | 1 |
Nearside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
Towbar excessively corroded within 30cm of towbar mounting (6.1.6 (i) (i)) | 1 |
Offside Stop lamp not working |1.2.1b| | 1 |
Rear fog lamp excessively damaged so that it is not visible from a reasonable distance |1.3.2d| | 1 |
Offside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 1 |
Exhaust system insecure |6.1.2 |a|| | 1 |
Rear Tie bar/rod has excessive play in a pin/bush |2.4.G.2| | 1 |
Rear Tie bar/rod rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Rear fog lamp missing |1.3.2a| | 1 |
Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill to jacking point |6.1.1 |c| |i|| | 1 |
Nearside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
Offside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (JACKING POINT) (6.1.1 (c) (i)) | 1 |
Offside Front Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill central (6.1.1 (c) (i)) | 1 |
Nearside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
Offside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Sill |6.1.B.2| | 1 |
Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Nearside Front Lower Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Front Lower Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point (5.3.6 (a) (i)) | 1 |
Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced crossmember |7.1.1 |a| |i|| | 1 |
Offside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced crossmember |7.1.1 |a| |i|| | 1 |
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch liner to chassis |7.1.1 |a| |i|| | 1 |
Offside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis holed and corroded (6.1.1 (c) (i)) | 1 |
Nearside Rear Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill corroded and holed (6.1.1 (c) (i)) | 1 |
Offside Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill corroded and holed (6.1.1 (c) (i)) | 1 |
Rear fog lamp emits a light other than red |1.3.2e| | 1 |
Offside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Rear Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |