| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 30 |
| Registration plate lamp issues | 19 |
| Headlamp aim out of alignment | 15 |
| Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 9 |
| Brake pipe excessively corroded | 8 |
| Offside Rear fog lamp not working |1.3.2b| | 7 |
| Rear fog lamp tell tale not working |1.3.1b| | 6 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
| Parking brake lever has no reserve travel |3.1.6b| | 5 |
| Brakes imbalanced across an axle | 5 |
| Registration plate issues | 5 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 4 |
| Rear fog lamp not working |1.3.2b| | 4 |
| Parking brake: efficiency below requirements |3.7.B.7| | 4 |
| Rear brake binding | 4 |
| Battery insecure |1.9.1| | 4 |
| Offside Rear fog lamp missing |1.3.2a| | 3 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 3 |
| Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 3 |
| Rear parking brake recording little or no effort | 3 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 3 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 3 |
| Brake hose excessively deteriorated | 3 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 3 |
| Offside Stop lamp not working |1.2.1b| | 3 |
| Front brake disc in such a condition that it is seriously weakened | 3 |
| Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 3 |
| Rear fog lamp switch missing |1.3.1a| | 2 |
| Service brake: efficiency below requirements |3.7.C.1a| | 2 |
| Offside Front Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
| Offside Rear Rear fog lamp missing |1.3.2a| | 2 |
| Nearside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 2 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Exhaust emissions test not completed because smoke levels are significantly in excess of the specified limit values (8.2.2.2 (f)) | 2 |
| Trailer electrical socket (13 pin) not operating the trailer lamps as intended (4.10 (c) (i)) | 2 |
| Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 2 |
| Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
| Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Rear brake application uneven | 2 |
| Nearside Battery insecure |1.9.1| | 2 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Emissions not tested |7.0| | 2 |
| Nearside Rear Lower Shock absorber has an excessively worn bush |2.7.4| | 2 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 2 |
| Nearside Stop lamp|s| not working |4.3.1 |a| |ii|| | 2 |
| Windscreen washer not working | 2 |
| Offside Rear Lower Shock absorber has an excessively worn bush |2.7.4| | 2 |
| Exhaust emissions exceed level of metered smoke for a turbo charged engine (8.2.2.2 (b)) | 2 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Nearside Rear Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 2 |
| Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
| Offside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Offside Rear fog lamp emits a light other than red |1.3.2e| | 2 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 2 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 2 |
| Rear Body has a sharp edge caused by damage |6.1.C.1| | 2 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Windscreen wiper blade insecure | 2 |
| Nearside Front Lower Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Brake pedal has insufficient reserve movement |3.3.A.5| | 1 |
| Fuel cap/sealing device missing (6.1.3 (b) (i)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill (6.1.1 (c) (i)) | 1 |
| Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Offside Front Headlamp not in good working order |not working| |1.2.4a| | 1 |
| Offside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt bottom ball joint
|2.4.G.2| | 1 |
| Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt bottom ball joint |2.4.G.2| | 1 |
| Offside Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Rear position lamp|s| incorrect colour |1.1.A.3e| | 1 |
| Nearside Stop lamp emits other than a steady red light |1.2.1e| | 1 |
| Offside Rear fog lamp insecure |1.3.2a| | 1 |
| Offside Front Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Emissions not tested major exhaust leak |7.4.B.1| | 1 |
| Nearside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded lower sill |5.2.6| | 1 |
| Offside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Rear Inner Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Outer Vehicle structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Fuel system component leaking fuel filter is leaking (6.1.3 (b) (i)) | 1 |
| Emissions unable to be completed fuel leak (8.2.2.2 (e)) | 1 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill under step (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength shock mouting (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Exhaust emissions exceed level of metered smoke for a non-turbo charged engine (8.2.2.2 (b)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength close to shock absorber top mount (5.3.6 (a) (i)) | 1 |
| Offside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength within 30 cms of shock absorber top mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength end of crossmember (5.3.6 (a) (i)) | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Prop shaft bearing housing insecure (6.1.7 (f) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced step (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Battery insecure lesure |1.9.1| | 1 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Nearside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Offside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Front Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Front Anti-roll bar pin or bush excessively worn D bushes (5.3.4 (a) (i)) | 1 |
| Offside Rear Shock absorbers has an excessively worn bush lower bush (5.3.2 (c)) | 1 |
| Nearside Rear Shock absorbers has an excessively worn bush upper bush (5.3.2 (c)) | 1 |
| Offside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Horn not working (7.7 (a)) | 1 |
| Hazard warning switch faulty |1.4.B.1d| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper shock mounting area, multiple holes (5.3.6 (a) (i)) | 1 |
| Nearside Front Brake prescribed area is excessively corroded where pipe comes into arch holed (1.1.21 (e) (i)) | 1 |
| Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced bumper supports both sides (6.1.1 (c) (i)) | 1 |
| Offside Obligatory mirror missing |8.1.1| | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area strength or continuity significantly reduced under step sill |7.1.1 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced under step |7.1.1 |a| |i|| | 1 |
| Nearside Rear Shock absorber insecure |2.7.2b| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Brake load sensing valve seized |3.6.E.3| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Nearside Rear Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside rear brake juddering severely |3.7.A.5b| | 1 |
| Nearside Front Upper Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings shocker top mounting |6.1.B.2| | 1 |
| Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Front brake application uneven | 1 |
| Inner Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Nearside Front Upper Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength OSR sill corroded within 30cm of rear suspension mount. (5.3.6 (a) (i)) | 1 |
| Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn d bush |5.3.4 |a| |i|| | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn d bush |5.3.4 |a| |i|| | 1 |
| Offside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Body panel corroded and likely to cause injury wheel arch (6.2.1 (a) (i)) | 1 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Power steering pipe/hose leaking (2.1.5 (a)) | 1 |
| Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Front Headlamp not working on main beam |1.7.5a| | 1 |
| Offside Front Prop shaft joint constant velocity boot no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
| Offside Rear fog lamp excessively damaged so that it is not visible from a reasonable distance |1.3.2d| | 1 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Nearside Rear position lamp|s| incomplete |1.1.4a| | 1 |
| Nearside Rear reflector excessively damaged so that its function is impaired |1.5.1c| | 1 |
| Nearside Stop lamp excessively damaged so that it is not visible from a reasonable distance |1.2.1d| | 1 |
| Nearside Rear Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Rear Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Brake servo vacuum pipe split |3.6.C.1b| | 1 |
| Brake performance not tested |3.7.A.1| | 1 |
| Parking brake: efficiency below requirements |3.7.C.1b| | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting insecure (5.3.3 (a) (i)) | 1 |
| Nearside Front Inner Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Inner Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Rear fog lamp insecure |1.3.2a| | 1 |
| Offside Rear brake disc contaminated by oil |3.5.1h| | 1 |
| Nearside Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Offside Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Fluid leak harmful to the environment or a risk to other road users Fuel |8.4.1 |a| |i|| | 1 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Fuel cap/sealing device mounting flange/sealing method defective |7.2.4c| | 1 |
| Rear Front drive shaft coupling bearing fastener insecure |2.5.C.2b| | 1 |
| Nearside Rear Upper Outline marker lamp not working |4.2.1 |a|| | 1 |
| Offside Rear Upper Outline marker lamp not working |4.2.1 |a|| | 1 |
| Nearside Rear Upper Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Upper Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
| Front Anti-roll bar pin or bush excessively worn both front (5.3.4 (a) (i)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner sill (6.2.2 (d) (i)) | 1 |
| Front Upper Integral body structure has excessive corrosion which adversely affects braking or steering upper bulkhead (6.1.1 (c) (ii)) | 1 |
| Nearside Front Bumper insecure (6.1.4 (a) (i)) | 1 |
| Nearside Rear Leaf spring shackle pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Leaf spring shackle pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Inner Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting inner wing (6.2.2 (d) (i)) | 1 |
| Nearside Front Body panel corroded and likely to cause injury wing (6.2.1 (a) (i)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired outer sill (6.2.2 (d) (ii)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion to the extent that overall security or stability of the body is impaired (6.2.2 (d) (ii)) | 1 |
| Offside Front Passenger`s seat insecure Left hand side vehicle |6.2.A.1| | 1 |
| Rear Exhaust system not adequately supported And centre joint |7.1.1| | 1 |
| Fuel pipe leaking |7.2.3| | 1 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 1 |
| Offside Statutory seat belt missing |5.1.1| | 1 |
| Nearside Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Nearside Front Valve stem seriously damaged |4.1.D.1e| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Inner sill areas |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded Inner sill areas |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Inner sill areas. |2.4.A.3| | 1 |
| Nearside Front Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength centre sill (5.3.6 (a) (i)) | 1 |
| Offside Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength centre sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength crossmember (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Central Rear Exhaust system insecure (6.1.2 (a)) | 1 |
| Central Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Emissions not tested exhaust snapped (8.2.1.2 (d)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced arch sections holed (6.1.1 (c) (i)) | 1 |
| Offside Rear Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced arch section holed (6.1.1 (c) (i)) | 1 |
| Offside Rear Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner and outer seals |2.4.A.3| | 1 |
| Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Rear Rear fog lamp missing |1.3.2a| | 1 |
| Nearside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Outer Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Outer Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Front lower cross member (5.3.6 (a) (i)) | 1 |
| Offside Steering rack gaiter missing or no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Steering rack gaiter split |2.2.D.2d| | 1 |
| Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Outer Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Outer Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Fuel system component leaking |7.2.3| | 1 |
| Rear Exhaust has a part missing |7.1.1a| | 1 |
| Exhaust emissions exceed manufacturers specified limit 1.05 (8.2.2.2 (a)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength multiple areas (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength multiple areas (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area is inadequately repaired inner arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area is inadequately repaired sill (5.3.6 (a) (i)) | 1 |
| Offside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Nearside Front Battery insecure |1.9.1| | 1 |
| Nearside Rear Brake load sensing valve seized |3.6.E.3| | 1 |
| Offside Rear Leaf spring shackle bracket loose |2.4.B.6a| | 1 |
| Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings x member |6.1.B.2| | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting insecure and impairing directional stability (5.3.3 (a) (ii)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 1 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Front Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Stop lamp emits other than a steady red light |1.2.1e| | 1 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Battery insecure |1.9.1| | 1 |
| Nearside Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Inner Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Front Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Nearside Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Rear Rear fog lamp not working |1.3.2b| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Outer Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Inner Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Inner Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Stop lamp not working |1.2.1b| | 1 |
| Nearside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt gaiter split |2.4.G.2| | 1 |
| Offside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt gaiter split |2.4.G.2| | 1 |
| Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt gaiter split |2.2.C.1c| | 1 |
| Offside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 1 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Front Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
| Offside Rear Anti-roll bar linkage pin or bush likely to become detached |5.3.4 |a| |ii|| | 1 |