| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 40 |
| Registration plate lamp issues | 32 |
| Headlamp aim out of alignment | 17 |
| Rear fog lamp not working |1.3.2b| | 12 |
| Offside Rear fog lamp not working |1.3.2b| | 11 |
| Nearside Stop lamp not working |1.2.1b| | 11 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 9 |
| Horn not working |1.6.2a| | 9 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 9 |
| Battery insecure |1.9.1| | 7 |
| Anti-lock braking system warning lamp indicates an ABS fault | 7 |
| Offside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 6 |
| Offside Stop lamp not working |1.2.1b| | 6 |
| Offside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 6 |
| Exhaust emits an excessive level of metered smoke for a turbo charged engine |7.4.B.3b| | 6 |
| Registration plate issues | 5 |
| Offside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 5 |
| Service brake: efficiency below requirements |3.7.B.7| | 5 |
| Brakes imbalanced across an axle | 5 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 5 |
| Brake pipe excessively corroded | 5 |
| Rear fog lamp missing |1.3.2a| | 4 |
| Nearside Rear Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 4 |
| Offside front brake binding |3.7.B.1| | 4 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 4 |
| Offside Rear fog lamp missing |1.3.2a| | 4 |
| Parking brake: efficiency below requirements |3.7.B.7| | 4 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 4 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 4 |
| Rear parking brake recording little or no effort | 4 |
| Offside Rear fog lamp not working (1.3.2b) | 4 |
| Rear fog lamp tell tale missing |1.3.1b| | 3 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 3 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 3 |
| Offside Rear Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 3 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
| Rear brake binding | 3 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 3 |
| Rear Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 3 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 3 |
| Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
| Rear fog lamp switch missing |1.3.1a| | 3 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Power steering component|s| leaking |2.3.3b| | 3 |
| Offside Rear Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Front brake disc in such a condition that it is seriously weakened | 2 |
| Rear fog lamp tell tale not working |1.3.1b| | 2 |
| Offside Rear Rear fog lamp emits a light other than red |1.3.2e| | 2 |
| Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 2 |
| Nearside front brake binding |3.7.B.1| | 2 |
| Fuel system component leaking |7.2.3| | 2 |
| Nearside Rear brake disc contaminated by oil |3.5.1h| | 2 |
| Rear brake disc in such a condition that it is seriously weakened | 2 |
| Offside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 2 |
| Nearside Front front brake binding |3.7.B.1| | 2 |
| Exhaust emits excessive smoke or vapour of any colour |7.4.B.4| | 2 |
| Nearside Rear Anti-roll bar linkage has excessive play in a pin/bush |2.4.G.2| | 2 |
| Spare wheel insecure |6.4.2| | 2 |
| Offside Front Upper Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 2 |
| Nearside Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
| Nearside Headlamp not working on main beam |1.7.5a| | 2 |
| Offside Headlamp not working on main beam |1.7.5a| | 2 |
| Emissions not tested |7.0| | 2 |
| Nearside Rear Stop lamp not working |1.2.1b| | 2 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 2 |
| Offside Rear position lamp|s| incorrect colour |1.1.A.3e| | 2 |
| Rear Rear fog lamp not working |1.3.2b| | 2 |
| Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Offside Front Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Central Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 2 |
| Rear Rear fog lamp missing |1.3.2a| | 2 |
| Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
| Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 2 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded Sill |2.4.A.3| | 2 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded Sill |2.4.A.3| | 2 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 2 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Nearside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
| Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
| Offside Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 2 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
| Offside Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Nearside Outer Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Outer Front Anti-roll bar linkage has excessive play in a ball joint |2.4.G.2| | 1 |
| Centre Stop lamp not working |1.2.1b| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under sill back |5.3.6 |a| |i|| | 1 |
| Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Nearside Rear Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Macpherson strut has excessive movement in the upper support bearing assembly top mount |2.5.B.1b| | 1 |
| Front brake excessively fluctuating | 1 |
| Offside Rear Inner Anti-roll bar attachment bracket/mounting insecure |5.3.3 |a| |i|| | 1 |
| Offside Front Anti-roll bar linkage insecurely attached |5.3.3 |a| |i|| | 1 |
| Electrical wiring insecure under bonnet |1.9.2a| | 1 |
| Offside Front Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Anti-roll bar linkage has excessive play in a ball joint nut not tight enough |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar linkage fractured securing bolt has been ground off |2.4.G.1| | 1 |
| Nearside Front Anti-roll bar has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
| Offside Headlamp light source and lamp not compatible (4.1.4 (c)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Upper Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength undersill (5.3.6 (a) (i)) | 1 |
| Nearside Front Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill corroded |6.2.2 |d| |i|| | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill corroded |6.2.2 |d| |i|| | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill corroded |6.2.2 |d| |i|| | 1 |
| Central Front Cab or chassis has excessive corrosion, seriously affecting its strength within 30cm of a cab mounting main front cross member is corroded |6.2.2 |d| |i|| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings outer sill |6.1.B.2| | 1 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
| Nearside Inner Front Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Inner Front Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Outer Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Rear fog lamp switch faulty |1.3.1a| | 1 |
| Driver`s seat insecure |6.2.A.1| | 1 |
| Offside Rear Anti-roll bar rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Centre Seat belt damaged sufficient to significantly weakened the webbing |5.2.2a| | 1 |
| Offside Rear Rear fog lamp excessively deteriorated so that it is not visible from a reasonable distance |1.3.2d| | 1 |
| Nearside Inner Seat belt anchorage prescribed area is excessively corroded sill x1 |5.2.6| | 1 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded sill x2 |5.2.6| | 1 |
| Nearside Headlamp lens seriously defective |4.1.1 |b| |ii|| | 1 |
| Offside Headlamp lens seriously defective |4.1.1 |b| |ii|| | 1 |
| Subframe mounting prescribed area excessively corroded significantly reducing structural strength front pannel |5.3.6 |a| |i|| | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Rear Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill and inner wheel arch |7.1.1 |a| |i|| | 1 |
| Nearside Rear Brake disc contaminated |1.1.14 |b|| | 1 |
| Nearside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
| Offside Headlamp lens seriously defective (4.1.1 (b) (ii)) | 1 |
| Nearside Rear Brake disc contaminated (1.1.14 (b)) | 1 |
| Exhaust system not adequately supported rear rubber broken |7.1.1| | 1 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Rear Anti-roll bar linkage fractured |2.4.G.1| | 1 |
| Exhaust has a major leak of exhaust gases back box |7.1.2| | 1 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Battery insecure leisure |1.9.1| | 1 |
| Offside Rear Anti-roll bar linkage insecure |2.4.G.1| | 1 |
| Rear Anti-roll bar rubber mounting deteriorated resulting in excessive movement D bushes both sides |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Nearside Rear Service brake excessively fluctuating |1.2.1 |e|| | 1 |
| Service brake efficiency below requirements |1.2.2 |a| |i|| | 1 |
| Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Front Lower Front suspension ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Side repeater not working |1.4.A.2c| | 1 |
| Nearside Headlamp aim beam image obviously incorrect Lens cloudy unable to see pattern |1.8.A.1b| | 1 |
| Rear Exhaust system not adequately supported Wire support insufficient |7.1.1| | 1 |
| Centre Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Nearside Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Nearside Front Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Anti-roll bar ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt (2.1.3 (g) (ii)) | 1 |
| Offside Ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Rear Suspension arm pin or bush excessively worn rear most bush (5.3.4 (a) (i)) | 1 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Front Suspension component mounting prescribed area is excessively corroded crossmember |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded sill panel |2.4.A.3| | 1 |
| Nearside Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 1 |
| Offside Front Wheel nut|s| missing |4.2.A.1e| | 1 |
| Offside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Nearside Rear Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Front position lamp|s| incorrect colour |1.1.A.3e| | 1 |
| Offside Front Front position lamp|s| incorrect colour |1.1.A.3e| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Suspension component mounting prescribed area is excessively corroded Nearside & offside rear sill closures |2.4.A.3| | 1 |
| Vehicle structure has excessive corrosion which adversely affects braking or steering offside front |inner arch | |6.1.A.1| | 1 |
| Offside Rear Fuel system component leaking |7.2.3| | 1 |
| Nearside Rear Lower Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Rear Lower Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Nearside Inner Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Direction indicators flashing less than 60 times a minute Not flashing |1.4.A.2g| | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Rear Seat belt missing (7.1.2 (a)) | 1 |
| Offside Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill X 3 (6.2.2 (d) (i)) | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILL |6.2.2 |d| |i|| | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILL |6.2.2 |d| |i|| | 1 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILL |6.2.2 |d| |i|| | 1 |
| Offside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting SILL |6.2.2 |d| |i|| | 1 |
| Nearside Rear Inner Integral body structure is deformed and structural rigidity is significantly reduced SILL |6.1.1 |a| |i|| | 1 |
| Offside Rear Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Offside Rear Anti-roll bar linkage rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
| Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Offside Rear Stop lamp emits other than a steady red light |1.2.1e| | 1 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Rear Rear position lamp(s) not working (1.1.A.3b) | 1 |
| Nearside Rear Stop lamp not working (1.2.1b) | 1 |
| Statutory seat belt missing Not checked (5.1.1) | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Inner sill (2.4.A.3) | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded Outer sill (2.4.A.3) | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Inner sill (2.4.A.3) | 1 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Front cross member o/s (6.1.B.2) | 1 |
| Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
| Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Major corrosion to inner sill. Slight corrosion to out sill (5.3.6 (a) (i)) | 1 |
| rear parking |secondary| brakes imbalanced | 1 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded sill/wheel arch |2.4.A.3| | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area is excessively corroded sill/wheel arch |2.4.A.3| | 1 |
| Offside Rear Rear position lamp|s| insecure |1.1.A.3a| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Nearside Front Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front brake disc excessively scored |3.5.1h| | 1 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Rear brake application uneven | 1 |
| Offside Headlamp aim beam image too far to the right |1.6.B4| | 1 |
| Offside Front Braking system leaking caliper |3.6.A.1| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded under step/chassis |2.4.A.3| | 1 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 1 |
| Nearside Rear Statutory seat belt missing |5.1.1| | 1 |
| Offside Rear Statutory seat belt missing |5.1.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded cross member |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded cross member |2.4.A.3| | 1 |
| Nearside Front Suspension arm ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Suspension arm ball joint dust cover insecure so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Brake pedal spongy |3.3.B.1b| | 1 |
| Statutory seat belt missing |5.1.1| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Offside Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Fuel cap/sealing device ineffective (6.1.3 (b) (i)) | 1 |
| Exhaust fumes causing a danger to health of persons on board (6.1.2 (b) (ii)) | 1 |
| Brake hose excessively deteriorated | 1 |
| Nearside Front Headlamp insecure (4.1.1 (c)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Within 30 cm suspension mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively damaged significantly reducing structural strength Within 30 cm suspension mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Integral body structure has excessive corrosion which adversely affects braking or steering sill holed and weak section (6.1.1 (c) (ii)) | 1 |
| Exhaust has a major leak of exhaust gases Rear silencer |7.1.2| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Inner wing |2.4.A.3| | 1 |
| Vehicle structure excessively corroded within 30cm of towbar mounting Rear crossmember |6.6.6| | 1 |
| Windscreen washer not working | 1 |
| Offside Position lamp not working |4.2.1 |a|| | 1 |
| Anti-lock braking system warning lamp does not illuminate |1.6 |a|| | 1 |
| Nearside Front Anti-lock braking system wiring excessively damaged |1.6 |d|| | 1 |
| Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings rear crossmember corroded and holed |6.1.B.2| | 1 |
| Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill holed |6.1.B.2| | 1 |
| Offside Front Body has a sharp edge caused by corrosion sill holed |6.1.C.1| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings front crossmember |6.1.B.2| | 1 |
| Offside Rear Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings wheel arch |6.1.B.2| | 1 |
| Centre Rear Statutory seat belt missing |5.1.1| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion wheel arch |6.1.C.1| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion wheel arch |6.1.C.1| | 1 |
| Offside Stop lamp emits other than a steady red light |1.2.1e| | 1 |
| Offside Rear Anti-roll bar linkage fractured |2.4.G.1| | 1 |
| Offside Rear Lower Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear fog lamp insecure (1.3.2a) | 1 |
| Central Exhaust has a major leak of exhaust gases (7.1.2) | 1 |
| Offside Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Offside Front Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting hole in sill within front subframe mount (6.2.2 (d) (i)) | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting hole in sill within rear suspension arm mount (6.2.2 (d) (i)) | 1 |
| Offside Rear fog lamp missing (1.3.2a) | 1 |
| Rear fog lamp tell tale not working (1.3.1b) | 1 |
| Rear fog lamp switch missing (1.3.1a) | 1 |
| Offside Stop lamp not working (1.2.1b) | 1 |
| Rear fog lamp missing (1.3.2a) | 1 |
| Front Front position lamp(s) not working (1.1.A.3b) | 1 |
| Rear Rear position lamp(s) not working (1.1.A.3b) | 1 |
| Offside Rear Tie bar/rod has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Rear fog lamp excessively deteriorated so that it is not visible from a reasonable distance |1.3.2d| | 1 |
| Nearside Battery insecure |1.9.1| | 1 |
| Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area is excessively corroded Sill |2.4.A.3| | 1 |
| Offside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Nearside Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outer sill (6.1.1 (c) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner wing (6.2.2 (d) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Front Anti-roll bar ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Rear fog lamp switch insecure |1.3.1a| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Exhaust system insecure (6.1.2 (a)) | 1 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Sub-frame corroded and seriously weakened |2.4.G.1| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Nearside Front Outer Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
| Offside Front Anti-roll bar linkage ball joint excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Front Shock absorbers has a serious fluid leak | 1 |
| Offside Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Nearside Rear Inner Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Nearside Rear Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced cross member |6.1.1 |c| |i|| | 1 |
| Nearside Front Service brake grabbing severely |3.7.C.2| | 1 |
| Offside Front Service brake grabbing severely |3.7.C.2| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Front Power steering component leaking pipe (2.1.5 (a)) | 1 |
| Emissions not tested (8.2.2.2 (e)) | 1 |
| Rear Anti-roll bar pin or bush excessively worn both D bushes (5.3.4 (a) (i)) | 1 |
| Nearside Rear Inner Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Rear Inner Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Rear Service brake excessively fluctuating (1.2.1 (e)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced sill end (7.1.1 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis outrigger (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Rear Vehicle structure excessively corroded within 30cm of towbar mounting cross member (6.1.6 (i) (i)) | 1 |
| Offside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Nearside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength x member |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength x member |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger |5.3.6 |a| |i|| | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Stop lamp not working |1.2.1b| | 1 |
| Nearside Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Centre Front Lower Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Rear fog lamp insecure |1.3.2a| | 1 |
| Nearside Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner and outer sill |5.3.6 |a| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill |5.3.6 |a| |i|| | 1 |
| Offside Rear Lower Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area is inadequately repaired outer sill |2.4.A.3| | 1 |
| Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength cross member (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar pin or bush excessively worn D bush (5.3.4 (a) (i)) | 1 |
| Rear Prop shaft joint so worn it is likely to fail (6.1.7 (c) (ii)) | 1 |
| Offside Windscreen wiper not operating over a large enough area to give an adequate view |8.2.1c| | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged or deteriorated so that it no longer prevents the ingress of dirt |2.1.3 |g| |ii|| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 1 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
| Rear fog lamp missing (4.5.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower body (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength lower body (5.3.6 (a) (i)) | 1 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Rear fog lamp insecure |1.3.2a| | 1 |
| Bootlid cannot be secured in the closed position |6.4.1| | 1 |
| Offside Rear fog lamp does not emit a steady red light |1.3.2e| | 1 |
| Exhaust emissions exceed level of metered smoke for a turbo charged engine |8.2.2.2 |b|| | 1 |
| Headlamp aim so that beam "kick up" is not visible on the screen both headlamps |4.1.2 |a|| | 1 |
| Steering rack gaiter missing or no longer prevents the ingress of dirt both front gaiters split |2.1.3 |g| |ii|| | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
| Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Body has a sharp edge caused by damage |6.1.C.1| | 1 |
| Nearside Front Lower Ball joint has excessive play |2.2.B.1f| | 1 |
| Central Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
| Nearside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Anti-roll bar linkage ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Rear passenger door cannot be opened from outside the vehicle |6.2.B.1c| | 1 |
| Nearside Front Lower Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Lower Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Offside Front Headlamp has a product on the lens so that the light output is severely reduced |4.1.4 |b|| | 1 |
| Offside Front Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
| Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
| Offside Front Anti-roll bar ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
| Brake lever has insufficient reserve travel |1.1.2 |a|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Power steering component|s| leaking steering rack |2.3.3b| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
| Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Subframe mounting prescribed area is excessively corroded Front crossmember |2.4.A.3| | 1 |
| Offside Front Steering rack gaiter split |2.2.D.2d| | 1 |
| Horn not working (7.7 (a) (ii)) | 1 |
| Offside Rear Lower Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Nearside Rear Upper Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Nearside Rear Outer Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting arch (6.2.2 (d) (i)) | 1 |
| Offside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting arch (6.2.2 (d) (i)) | 1 |
| Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced to places (7.1.1 (a) (i)) | 1 |
| Nearside Headlamp has a product on the lens so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front front brake binding |3.7.B.1| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings cross member |6.1.B.2| | 1 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Front Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Offside Front Vehicle structure fractured seriously affecting its strength within 30cm of towbar mounting inner sill (6.1.6 (i) (i)) | 1 |
| Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting inner sill +inner wheel arch (6.1.6 (i) (i)) | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
| Nearside Headlamp not working on main beam |4.1.1 |a| |ii|| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced inner sill |7.1.1 |a| |i|| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill |7.1.1 |a| |i|| | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting insecure |5.3.3 |a| |i|| | 1 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Nearside Front Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Speedometer clearly inoperative (7.8 (b) (ii)) | 1 |
| Offside Rear Anti-roll bar attachment bracket/mounting fractured (5.3.3 (b) (ii)) | 1 |
| Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded outrigger |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Nearside Rear Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner arch |5.2.6| | 1 |
| Suspension component mounting prescribed area is excessively corroded front crossmember - offside/nearside |2.4.A.3| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded outer sill - marked |5.2.6| | 1 |
| Offside Seat belt anchorage prescribed area is excessively corroded inner sill - marked |5.2.6| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner arch/sill |5.2.6| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded inner/outer sill |2.4.A.3| | 1 |
| Nearside Front Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Lower Anti-roll bar linkage ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Rear Anti-roll bar pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Power steering ram|s| leaking from a failed seal |2.3.3b| | 1 |
| Nearside Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Outer Rear Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Inner Floor excessively deteriorated |6.2.4 |a| |i|| | 1 |