| Most common failures | No# failures |
|---|
| Headlamp aim out of alignment | 24 |
| Windscreen wiper does not clear the windscreen effectively | 21 |
| Brake pipe excessively corroded | 17 |
| Registration plate issues | 14 |
| Anti-lock braking system warning lamp indicates an ABS fault | 11 |
| Registration plate lamp issues | 10 |
| Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 6 |
| Parking brake: efficiency below requirements |3.7.B.7| | 6 |
| Brakes imbalanced across an axle | 5 |
| Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 5 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 4 |
| Engine MIL inoperative or indicates a malfunction |8.2.1.2 |h|| | 4 |
| Offside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 3 |
| Offside Front Direction indicator not working |1.4.A.2c| | 3 |
| Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 3 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 3 |
| Supplementary Restraint System warning lamp indicates a fault |5.4.2| | 3 |
| Engine MIL inoperative or indicates a malfunction (8.2.1.2 (h)) | 3 |
| Rear parking brake recording little or no effort | 3 |
| Parking brake lever has no reserve travel |3.1.6b| | 2 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 2 |
| Emissions not tested |7.3.A.1| | 2 |
| Nearside Front Seat belt retracting mechanism defective |5.2.5b| | 2 |
| Windscreen has damage | 2 |
| Nearside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 2 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 2 |
| Brake hose excessively deteriorated | 2 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 2 |
| Nearside Rear Sub-frame attachment rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Offside Rear Sub-frame attachment rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Nearside Rear Drive shaft uj which forms part of the suspension has excessive play in a universal joint inner and outer |2.4.G.4b| | 2 |
| Offside Rear Drive shaft uj which forms part of the suspension has excessive play in a universal joint inner and outer |2.4.G.4b| | 2 |
| Offside Rear fog lamp not working |1.3.2b| | 2 |
| Offside Rear Stop lamp not working |1.2.1b| | 2 |
| Offside Stop lamp not working |1.2.1b| | 2 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 2 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Rear fog lamp tell tale not working |1.3.1b| | 2 |
| Parking brake inoperative on one side BOTH SIDES (1.4.1 (a)) | 1 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn bush missing (5.3.4 (a) (i)) | 1 |
| Subframe mounting prescribed area excessively corroded significantly reducing structural strength rear subframe at both front mountings... (5.3.6 (a) (i)) | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 1 |
| Offside Rear Brake cable damaged (1.1.15 (a)) | 1 |
| Offside Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Nearside Rear Body panel corroded and likely to cause injury lower wheel arch (6.2.1 (a) (i)) | 1 |
| Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
| Offside Obligatory mirror missing (3.3 (a)) | 1 |
| Offside Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced chassis on floor.. (7.1.1 (a) (i)) | 1 |
| Nearside Rear Anti-roll bar linkage pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Bonnet cannot be secured in the closed position (3.1 (b) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced floor at jacking point (7.1.1 (a) (i)) | 1 |
| Nearside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Outer Seat belt anchorage prescribed area is inadequately repaired sill (7.1.1 (a) (i)) | 1 |
| Offside Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis leg (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor at jacking point (5.3.6 (a) (i)) | 1 |
| Nearside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper and lower wheel arch at shock mount (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength upper and lower wheel arch at shock mount (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced nearside sill (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced offside sill (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength next to upper arm (5.3.6 (a) (i)) | 1 |
| Offside Front Anti-roll bar ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Rear Bumper likely to become detached (6.1.4 (a) (ii)) | 1 |
| Nearside Front Position lamp not working |4.2.1 |a|| | 1 |
| Nearside Rear Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
| Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Drive shaft uj which forms part of the suspension has excessive play in a universal joint |2.4.G.4b| | 1 |
| Offside Drive shaft uj which forms part of the suspension has excessive play in a universal joint |2.4.G.4b| | 1 |
| Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.1 |c| |ii|| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.1 |c| |ii|| | 1 |
| Nearside Rear Fuel pipe leaking |6.1.3 |b| |i|| | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor section corroded through (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component attachment bracket/mounting corroded and seriously weakened axle mounting bracket badly corroded away (5.3.3 (b) (i)) | 1 |
| Emissions not tested |8.2.1.2 |d|| | 1 |
| Brake pedal creeps down when held under pressure |3.3.B.1a| | 1 |
| Nearside Front position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Rear Radius arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Rear Sub-frame corroded and seriously weakened |2.4.G.1| | 1 |
| Nearside Rear passenger door cannot be opened from outside the vehicle |6.2.B.1c| | 1 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Windscreen washer not working | 1 |
| Offside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Electrical wiring insulation so damaged or deteriorated it is likely to cause a short-circuit wires around steering column (4.11 (c) (ii)) | 1 |
| Offside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Floor |6.1.B.2| | 1 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Front Inner Steering rack gaiter insecure |2.2.D.2d| | 1 |
| Nearside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inside wheel arch (5.3.6 (a) (i)) | 1 |
| Engine MIL inoperative or indicates a malfunction indicating fault (8.2.1.2 (h)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inside wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inside wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Jacking point (5.3.6 (a) (i)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded Flitch panel behind Shock absorber... |2.4.A.3| | 1 |
| Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Exhaust Lambda reading after 2nd fast idle outside specified limits too high (8.2.1.2 (c)) | 1 |
| Offside Rear Seat belt flexible stalk damaged missing (7.1.2 (b) (i)) | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings under wheel arch near shocker mount |6.1.B.2| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings under wheel arch near shocker mount |6.1.B.2| | 1 |
| Offside Front coil spring incomplete |2.4.C.1a| | 1 |
| Headlamp levelling device cannot be operated from the drivers seat (4.1.5 (b)) | 1 |
| Electronic braking system warning device indicates a fault came on during test (1.7 (b)) | 1 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength sill corroded within 30cm of rear subframe mounting plate (5.3.6 (a) (i)) | 1 |
| Nearside Rear Lower Seat belt anchorage prescribed area strength or continuity significantly reduced corrosion within 30cm of lower outer seat belt mounting point (7.1.1 (a) (i)) | 1 |
| Front Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Centre Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Nearside Headlamp levelling device cannot be operated from the drivers seat (4.1.5 (b)) | 1 |
| Offside Headlamp levelling device cannot be operated from the drivers seat (4.1.5 (b)) | 1 |
| Offside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Steering rack insecure to the extent there is excessive movement at the mountings (2.1.3 (a) (ii)) | 1 |
| Nearside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 1 |
| Exhaust emissions likely to be affected by an exhaust leak (8.2.1.1 (b)) | 1 |
| Offside Rear Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch area (5.3.6 (a) (i)) | 1 |
| Offside Front Coil spring fractured or broken (5.3.1 (b) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension arm ball joint excessively worn and off side (5.3.4 (a) (i)) | 1 |
| Rear Lower Suspension arm has excessive play in a pin/bush both |2.4.G.2| | 1 |
| Nearside Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Nearside Rear Lower Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Rear Lower Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Anti-roll bar linkage rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Emissions not tested |7.0| | 1 |
| Rear Rear fog lamp not working |1.3.2b| | 1 |
| Nearside Rear Stop lamp not working |1.2.1b| | 1 |
| Fuel cap/sealing device mounting flange/sealing method defective |7.2.4c| | 1 |
| Nearside Front Suspension arm attachment bracket/mounting insecure |2.4.G.1| | 1 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength floor near subframe mounting (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill/floor around jacking point (7.1.1 (a) (i)) | 1 |
| Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill/wheel arch (7.1.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Brake performance not tested nearside ridged brake pipe fractured (1.2.1 (g)) | 1 |
| Nearside Front Service brake excessively binding |1.2.1 |f|| | 1 |
| Electronic stability control warning lamp indicates a fault |7.12 |e|| | 1 |
| Nearside Stop lamp not working |1.2.1b| | 1 |
| Rear fog lamp not working |1.3.2b| | 1 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Rear position lamp|s| incomplete |1.1.4a| | 1 |
| Exhaust hydrocarbon content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 1 |
| Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 1 |
| Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 1 |
| Nearside Front Anti-roll bar linkage ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Offside Headlamp insecure |1.7.3| | 1 |
| Offside Front Exhaust has a major leak of exhaust gases cat
|7.1.2| | 1 |
| Nearside Front Inner Ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Front Lower Ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Outer sill holed |6.1.B.2| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Inner sill holed |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Outer sill holed |6.1.B.2| | 1 |
| Offside Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Nearside Rear Drive shaft uj which forms part of the suspension has excessive play in a universal joint |2.4.G.4b| | 1 |
| Offside Rear Drive shaft uj which forms part of the suspension has excessive play in a universal joint |2.4.G.4b| | 1 |
| Nearside Front Upper Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Front Coil spring corroded so that its cross sectional area is reduced and seriously weakened |5.3.1 |b| |i|| | 1 |
| Offside Front Coil spring fractured or broken |5.3.1 |b| |i|| | 1 |
| Nearside Rear Vehicle structure has a fracture which is likely to adversely affect braking or steering |6.1.1 |a| |ii|| | 1 |
| Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength at inner sill (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner sill |6.1.B.2| | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Headlamp insecure (4.1.1 (c)) | 1 |
| Side repeater not working |1.4.A.2c| | 1 |
| Offside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Nearside Front Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement lower bush |2.4.G.2| | 1 |
| Offside Front Anti-roll bar linkage rubber bush deteriorated resulting in excessive movement lower bush |2.4.G.2| | 1 |
| Nearside Front Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Offside Front Shock absorber has an excessively worn bush |2.7.4| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
| Nearside Rear Exhaust has a major leak of exhaust gases back box missing |7.1.2| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting jacking area (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting jack area (6.2.2 (d) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting jack area (6.2.2 (d) (i)) | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor pan central (6.2.2 (d) (i)) | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting floor (6.2.2 (d) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Nearside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Offside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Nearside Rear wheel bearing has excessive play |2.6.2| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Floor panel |5.3.6 |a| |i|| | 1 |
| Nearside Front Lower Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Front Upper Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Horn not working |1.6.2a| | 1 |
| Offside Front Direction indicator not working |4.4.1 |a| |ii|| | 1 |
| Nearside Front Direction indicator incomplete |1.5.A1b| | 1 |
| Nearside Front Anti-roll bar linkage pin or bush excessively worn |5.3.4 |a| |i|| | 1 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |