Most common failures | No# failures |
---|
Headlamp aim out of alignment | 34 |
Registration plate lamp issues | 16 |
Windscreen wiper does not clear the windscreen effectively | 11 |
Brake hose excessively deteriorated | 9 |
Parking brake: efficiency below requirements |3.7.B.7| | 6 |
Rear parking brake recording little or no effort | 5 |
Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 4 |
Brake pipe excessively corroded | 4 |
Offside Headlamp not working on dipped beam |1.7.5a| | 4 |
Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 3 |
Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 3 |
Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 3 |
Offside Front position lamp|s| not working |1.1.A.3b| | 3 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 2 |
Offside Front wheel bearing has excessive play |2.5.A.3c| | 2 |
Offside Front coil spring incomplete |2.4.C.1a| | 2 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 2 |
Nearside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 2 |
Offside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 2 |
Nearside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 2 |
Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 2 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Front Upper Suspension arm has excessive play in a ball joint |2.4.G.2| | 2 |
Offside Rear Stop lamp not working |1.2.1b| | 2 |
Offside Rear Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
Offside Rear position lamp|s| not working |1.1.A.3b| | 2 |
Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 2 |
Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 2 |
Offside Rear Rear position lamp|s| not working |1.1.A.3b| | 2 |
Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
Front brake disc in such a condition that it is seriously weakened | 2 |
Rear brake disc in such a condition that it is seriously weakened | 2 |
Rear fog lamp switch faulty |1.3.1a| | 2 |
Offside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Front coil spring cracked |2.4.C.1a| | 1 |
Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 1 |
Offside Rear Lower Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
Front brake disc excessively scored |3.5.1h| | 1 |
Brakes imbalanced across an axle | 1 |
Offside Front Power steering pipe|s| or hose|s| leaking |2.3.3b| | 1 |
Nearside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced n/s and o/s inner sills |6.1.1 |c| |i|| | 1 |
Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced sill |6.1.1 |c| |i|| | 1 |
Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced n/s and o/s inner wings |6.1.1 |c| |i|| | 1 |
Offside Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 1 |
Nearside Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 1 |
Offside Seat belt anchorage prescribed area is excessively corroded floor to sill |5.2.6| | 1 |
Nearside Seat belt anchorage prescribed area is excessively corroded floor to sill |5.2.6| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded floor near jacking point |2.4.A.3| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded floor near jacking point |2.4.A.3| | 1 |
Offside Front Upper Shock absorber has an excessively worn bush |2.7.4| | 1 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded inner arch |5.2.6| | 1 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
Nearside Rear Seat belt anchorage prescribed area is excessively corroded inner arch |5.2.6| | 1 |
Nearside Rear Outer Seat belt anchorage prescribed area is excessively corroded arch |5.2.6| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded arch, sill, inner sill |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded inner arch, outer arch |2.4.A.3| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded inner floor pan |2.4.A.3| | 1 |
Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Rear Sub-frame corroded and seriously weakened |2.4.G.1| | 1 |
Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Direction indicator not working |1.4.A.2c| | 1 |
Offside Front Direction indicator not working |1.4.A.2c| | 1 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Steering rack gaiter insecure |2.2.D.2d| | 1 |
Offside Steering rack gaiter insecure |2.2.D.2d| | 1 |
Offside Front Steering arm has relative movement at its fixings |2.2.B.1h| | 1 |
Nearside Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
Nearside Front Service brake excessively binding (1.2.1 (f)) | 1 |
Nearside Front Service brake lagging in operation (1.2.1 (d)) | 1 |
Nearside Front Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
Offside Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Offside Front Headlamp aim not tested |4.1.2 |b|| | 1 |
Stop lamp|s| all not working |4.3.1 |a| |iii|| | 1 |
Windscreen has damage | 1 |
Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
Offside Steering rack insecure |2.2.B.1a| | 1 |
Offside Front Upper Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Nearside Front Headlamp insecure |1.7.3| | 1 |
Service brake: efficiency below requirements |3.7.B.7| | 1 |
Offside Rear Brake back plate|s| securing device excessively deteriorated |3.5.1j| | 1 |
Central Lower Emissions not tested exhaust silencer holed |7.3.A.1| | 1 |
Nearside Front Seat belt affected by an insecure seat fixing |5.2.1b| | 1 |
Nearside Stop lamp not working |1.2.1b| | 1 |
Steering column top bearing excessively worn |2.1.2c| | 1 |
Nearside Front suspension has excessive movement at a wishbone pin or bush |2.5.A.1c| | 1 |
Nearside Inner Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Inner Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
All position lamps not working |1.1.A.3b| | 1 |
Nearside Floor excessively deteriorated Floor to inner sill. (6.2.4 (a) (i)) | 1 |
Offside Floor excessively deteriorated Floor to inner sill corroded. (6.2.4 (a) (i)) | 1 |
Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength Outer door sill corroded. (5.3.6 (a) (i)) | 1 |
Nearside Front Upper Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
Offside Front Upper Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 1 |
Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 1 |
Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 1 |
Nearside Front Body panel corroded and likely to cause injury Wing edge corroded. (6.2.1 (a) (i)) | 1 |
Offside Front Body panel corroded and likely to cause injury Wing edge corroded. (6.2.1 (a) (i)) | 1 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Brake hydraulic reservoir leaking hydraulic fluid |3.6.A.1| | 1 |
Offside Headlamp insecure |1.7.3| | 1 |
Offside Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Steering column top mounting bracket insecure |2.1.2d| | 1 |
Offside Rear Position lamp showing white light to the rear (4.2.3 (a) (ii)) | 1 |
Offside Rear Position lamp lens seriously defective (4.2.1 (b)) | 1 |
Brake fluid contaminated (1.8 (a)) | 1 |
Supplementary restraint system warning lamp indicates a fault (7.1.6 (a)) | 1 |
Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 1 |
Supplementary restraint system warning lamp indicates a fault |7.1.6 |a|| | 1 |
Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 1 |
Front Subframe mounting prescribed area is excessively corroded o/s and n/s floor to sill as marked |2.4.A.3| | 1 |
Centre Exhaust mounting missing |7.1.1b| | 1 |
Nearside Rear Stop lamp not working |1.2.1b| | 1 |
Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
Speedometer not complete |6.7.2| | 1 |
Brake pedal spongy |3.3.B.1b| | 1 |
Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded floor pan to inner sill edges holed & corroded x2 holes |5.2.6| | 1 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded lower inner wheel arch holed & corroded |5.2.6| | 1 |
Offside Front Seat belt anchorage prescribed area is excessively corroded floor pan holed & corroded |5.2.6| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded floor pan corroded |2.4.A.3| | 1 |
Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 1 |
Nearside Rear Direction indicators incorrect colour |1.4.A.2f| | 1 |
Rear brake binding | 1 |
Power steering malfunctioning |2.3.3a| | 1 |
Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
Nearside Rear Sub-frame attachment rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Rear Sub-frame attachment rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Obligatory mirror insecure |8.1.1| | 1 |
Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Nearside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Rear Seat belt anchorage prescribed area is excessively corroded floor pan |5.2.6| | 1 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded chassis leg |2.4.A.3| | 1 |
Offside Rear Exhaust system not adequately supported |7.1.1| | 1 |
Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Parking brake lever has no reserve travel |3.1.6b| | 1 |
Nearside Front coil spring broken |2.4.C.1a| | 1 |
Nearside Rear Lower Suspension arm has excessive play in a pin/bearing |2.4.G.2| | 1 |
Nearside Front Anti-roll bar linkage insecure |2.4.G.1| | 1 |
Power steering pipe|s| or hose|s| leaking from a joint |2.3.3b| | 1 |
Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inside wheel arch at front of sill |6.2.2 |d| |i|| | 1 |
Offside Rear Sub-frame rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Rear fog lamp tell tale not working |1.3.1b| | 1 |
Offside Rear fog lamp not working |1.3.2b| | 1 |
Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
Offside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Bonnet cannot be secured in the closed position |8.4.1| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Sub-frame rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Sub-frame rubber bush bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |