Most common failures | No# failures |
---|
Parking brake: efficiency below requirements |3.7.B.7| | 53 |
Headlamp aim out of alignment | 37 |
Brake pipe excessively corroded | 33 |
Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 23 |
Rear parking brake recording little or no effort | 20 |
Windscreen wiper does not clear the windscreen effectively | 20 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 19 |
Registration plate lamp issues | 19 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 16 |
Offside Rear fog lamp not working |1.3.2b| | 16 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 9 |
Exhaust has a major leak of exhaust gases |7.1.2| | 8 |
Brake hose excessively deteriorated | 8 |
Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 8 |
Rear fog lamp not working |1.3.2b| | 7 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 7 |
Service brake: efficiency below requirements |3.7.B.7| | 7 |
Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 7 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 6 |
Offside Headlamp not working on dipped beam |1.7.5a| | 6 |
Brakes imbalanced across an axle | 6 |
Registration plate issues | 6 |
Offside Drag link end ball joint has excessive play |2.2.B.1f| | 6 |
Nearside Front Sub-frame attachment rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 6 |
Parking brake lever has no reserve travel |3.1.6b| | 6 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
Horn not working |1.6.2a| | 5 |
Steering box has relative movement between sector shaft and the drop arm |2.2.B.1b| | 5 |
Rear brake binding | 5 |
Parking brake: efficiency below requirements |3.7.C.1b| | 5 |
Front Headlamp not working on main beam |1.7.5a| | 4 |
Steering system has excessive free play detected at the steering wheel |steering box fitted| |2.2.A.1a| | 4 |
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 4 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 4 |
Nearside Headlamp not working on main beam |1.7.5a| | 4 |
Offside Headlamp not working on main beam |1.7.5a| | 4 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
Offside Rear Rear fog lamp not working |1.3.2b| | 4 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 4 |
Windscreen washer not working | 4 |
Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
Nearside Front Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 3 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 3 |
Headlamp not working on dipped beam |1.7.5a| | 3 |
Nearside Stop lamp not working |1.2.1b| | 3 |
Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 3 |
Offside Intermediate drop arm insecure |2.2.B.1a| | 3 |
Steering box has a significant oil leak |2.2.D.2e| | 3 |
Offside Front Drag link end ball joint has excessive play |2.2.B.1f| | 3 |
Front Headlamp not working on dipped beam |1.7.5a| | 3 |
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
Nearside Front Bonded suspension unit bonding failed and part of unit is likely to become displaced |2.4.F.2| | 3 |
Offside Front Bonded suspension unit bonding failed and part of unit is likely to become displaced |2.4.F.2| | 3 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
Offside Rear Exhaust system not adequately supported |7.1.1| | 3 |
Offside Front Sub-frame attachment rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 3 |
Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 3 |
Nearside Rear Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
Headlamp not working on main beam |1.7.5a| | 3 |
Offside Stop lamp not working |1.2.1b| | 3 |
Rear fog lamp tell tale not working |1.3.1b| | 3 |
Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
Offside Side repeater not working |1.4.A.2c| | 3 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Offside Rear Brake pipe leaking |3.6.A.1| | 2 |
Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
Offside rear brake recording little or no effort |3.7.B.5a| | 2 |
Nearside Front Sub-frame attachment rubber mounting bonding deteriorated resulting in excessive movement |2.4.G.2| | 2 |
Offside Front Sub-frame attachment rubber mounting bonding deteriorated resulting in excessive movement |2.4.G.2| | 2 |
Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Battery insecure |1.9.1| | 2 |
Nearside Steering arm has relative movement at its fixings |2.2.B.1h| | 2 |
Offside Obligatory mirror insecure |8.1.1| | 2 |
Power steering pump leaking from a failed component |2.3.3b| | 2 |
Steering column top bearing excessively worn |2.1.2c| | 2 |
Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Nearside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 2 |
Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
Offside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 2 |
Parking brake: efficiency below requirements (3.7.B.7) | 2 |
Offside Rear rear brake recording little or no effort |3.7.B.5a| | 2 |
Offside Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 2 |
Nearside Front Side repeater not working |1.4.A.2c| | 2 |
Offside Rear Suspension component mounting prescribed area is excessively corroded chassis |2.4.A.3| | 2 |
Offside Ball joint has excessive play |2.2.B.1f| | 2 |
Nearside Rear Lower Suspension arm has excessive play in a pin/bush |2.4.G.2| | 2 |
Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Offside Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 2 |
Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 2 |
Nearside Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 2 |
Horn not working (7.7 (a)) | 2 |
Nearside front brake binding |3.7.B.1| | 2 |
Offside front brake binding |3.7.B.1| | 2 |
Offside Front Upper Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
Horn not working (7.7 (a) (ii)) | 2 |
Power steering component|s| leaking from a failed seal |2.3.3b| | 2 |
Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Offside Seat belt anchorage prescribed area is inadequately repaired |5.2.6| | 2 |
Centre Exhaust system not adequately supported |7.1.1| | 2 |
Nearside Side repeater not working |1.4.A.2c| | 2 |
Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
Offside Front position lamp|s| not working |1.1.A.3b| | 2 |
Nearside Front Seat belt locking mechanism does not secure or release |5.2.5a| | 2 |
Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 2 |
Offside Front Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Offside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Offside Rear Trailing arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Brake pedal creeps down while the pedal is held under pressure |3.3.B.1a| | 1 |
Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Nearside Sub-frame rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Sub-frame rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Rear Inner Seat belt anchorage prescribed area strength or continuity significantly reduced wheel arch (7.1.1 (a) (i)) | 1 |
Nearside Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Nearside Rear Seat belt anchorage prescribed area strength or continuity significantly reduced Wheel acrh (7.1.1 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Front Drag link end ball joint has excessive play |2.2.B.1f| | 1 |
Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Shock absorber has a serious fluid leak |2.7.3| | 1 |
Drag link end ball joint has excessive play OFF STEERING DROP ARM |2.2.B.1f| | 1 |
Ball joint has excessive play |2.2.B.1f| | 1 |
Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Offside Rear Brake pipe leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
Offside Rear Vehicle structure is fractured and structural rigidity is significantly reduced above trailing arm (6.1.1 (a) (i)) | 1 |
Nearside Rear Vehicle structure is fractured and structural rigidity is significantly reduced floorpan (6.1.1 (a) (i)) | 1 |
Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
Offside Rear Valve stem seriously damaged |4.1.D.1e| | 1 |
Offside Rear Parking brake mechanism/associated mounting prescribed area is excessively corroded |3.1.9| | 1 |
Offside Front Upper Ball joint has excessive play |2.2.B.1f| | 1 |
Offside Front Lower Ball joint has excessive play |2.2.B.1f| | 1 |
Nearside Rear Suspension spring mounting prescribed area is deliberately modified which significantly reduces the original strength 3 areas |2.4.A.3| | 1 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded 4 areas |2.4.A.3| | 1 |
Nearside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Offside Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
Nearside Inner Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Inner Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Outer Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
Nearside Front Upper Suspension component insecurely attached Forward mounting plate / rubber mounting, separated. (5.3.3 (a) (i)) | 1 |
Offside Front Lower Suspension component insecurely attached Forward mounting plate / rubber mounting separated. (5.3.3 (a) (i)) | 1 |
Nearside Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Brake pedal spongy |3.3.B.1b| | 1 |
Nearside Front Upper Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Front Upper Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Rear Exhaust system not adequately supported |7.1.1| | 1 |
Hazard warning tell tale not working correctly |1.4.B.1e| | 1 |
Nearside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Rear Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Offside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
Front Power steering pipe|s| or hose|s| leaking |2.3.3b| | 1 |
Steering system excessively rough |2.2.D.1| | 1 |
Indicator tell tale inoperative |1.4.A.2a| | 1 |
Side repeater not working |1.4.A.2c| | 1 |
Offside Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Intermediate drop arm insecure |2.2.B.1a| | 1 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Ball joint has excessive play |2.2.B.1f| | 1 |
Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Direction indicators flashing more than 120 times a minute |1.4.A.2g| | 1 |
Nearside Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
Offside Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
Offside Rear Exhaust mounting missing |7.1.1b| | 1 |
Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
Nearside Front Brake hose leaking |3.6.A.1| | 1 |
Offside Front Outer Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Front Inner Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement Front bush |2.4.G.2| | 1 |
Offside Front Lower Suspension arm rubber bush bonding deteriorated resulting in excessive movement Rear bush |2.4.G.2| | 1 |
Offside Front Drag link end ball joint has excessive play steering box drop arm end joint | drag link end| |2.2.B.1f| | 1 |
Nearside Front Headlamp not working on main beam |1.7.5a| | 1 |
Offside Front Headlamp not working on main beam |1.7.5a| | 1 |
Nearside Front Suspension arm rubber mounting bonding deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded floor |2.4.A.3| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded inner sill |2.4.A.3| | 1 |
Offside Rear Sub-frame attachment rubber mounting deteriorated resulting in excessive movement front and rear bushes |2.4.G.2| | 1 |
Nearside Front Upper Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Emissions not tested car ran out of petrol (8.2.1.2 (d)) | 1 |
Horn not working (1.6.2a) | 1 |
Parking brake lever has no reserve travel (3.1.6b) | 1 |
Offside Rear Braking system leaking caliper bleed nipple |3.6.A.1| | 1 |
Front Horn not working |1.6.2a| | 1 |
Offside Front Side repeater not working |1.4.A.2c| | 1 |
Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Rear Parking brake lever has no reserve travel |3.1.6b| | 1 |
Offside Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 1 |
Offside Rear Radius arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Rear Brake pipe fouled by moving parts |3.6.B.2a| | 1 |
Centre Rear Brake pipe excessively damaged |3.6.B.2c| | 1 |
Rear Rear fog lamp missing |1.3.2a| | 1 |
Rear Rear fog lamp tell tale not working |1.3.1b| | 1 |
Offside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Nearside Front Anti-roll bar fractured drop link |2.4.G.1| | 1 |
Indicator tell tale inoperative both |1.4.A.2a| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded chassis |2.4.A.3| | 1 |
Offside Brake actuating linkage mounting prescribed area is excessively corroded bulkhead |3.3.A.2| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded sill end |2.4.A.3| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
Exhaust emits excessive dense blue smoke during acceleration |7.3.A.2c| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded jacking point |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 1 |
Power steering component leaking (2.1.5 (a)) | 1 |
Front Anti-roll bar pin or bush excessively worn d mounts (5.3.4 (a) (i)) | 1 |
Fuel system component leaking excessively or a risk of fire rear carb ? |6.1.3 |b| |ii|| | 1 |
Parking brake efficiency less than 50% of the required value |1.4.2 |a| |ii|| | 1 |
Offside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Service brake is causing the vehicle to swerve to the offside |3.7.C.2| | 1 |
Nearside Front Body or chassis has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
Offside Front Power steering component|s| leaking |2.3.3b| | 1 |
Fuel system component leaking |7.2.3| | 1 |
Nearside Rear brake disc contaminated by oil |3.5.1h| | 1 |
Nearside Front Upper Ball joint has excessive play |2.2.B.1f| | 1 |
Nearside Front Drag link end ball joint has excessive play |2.2.B.1f| | 1 |
Offside Rear brake disc excessively scored |3.5.1h| | 1 |
Offside Rear Trailing arm attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
Nearside Front Upper Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 1 |
Offside Front Anti-roll bar linkage insecure |2.4.G.1| | 1 |
Nearside Rear Upper Bonded suspension unit bonding failed and part of unit is likely to become displaced |2.4.F.2| | 1 |
Brake performance not tested |3.7.A.1| | 1 |
Hazard warning switch faulty |1.4.B.1d| | 1 |
Power steering ram|s| leaking from a failed seal |2.3.3b| | 1 |
Brake has no servo assistance |3.3.B.2| | 1 |
Nearside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Sub-frame insecure |2.4.G.1| | 1 |
Front Upper Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Rear brake caliper has restricted free movement |3.5.1k| | 1 |
Nearside Front Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Front Ball joint has excessive play |2.2.B.1f| | 1 |
Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 1 |
Nearside Front Battery insecure |1.9.1| | 1 |
Nearside Front Anti-roll bar attachment bracket/mounting bolt missing |2.4.G.1| | 1 |
Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
Nearside Front Bonded suspension unit deteriorated and cannot function as intended |2.4.F.3| | 1 |
Offside Rear Bonded suspension unit deteriorated and cannot function as intended |2.4.F.3| | 1 |
Centre Upper Stop lamp not working |1.2.1b| | 1 |
Nearside Front Lower Axle swivel joint has excessive play in a ball joint |2.5.A.3b| | 1 |
Offside Front Lower Axle swivel joint has excessive play in a ball joint |2.5.A.3b| | 1 |
Nearside Steering pivot point has excessive play |2.2.B.1g| | 1 |
Nearside Front Direction indicator not working |4.4.1 |a| |ii|| | 1 |
Offside Inner Drag link end ball joint has excessive play |2.2.B.1f| | 1 |
Front position lamp|s| not working |1.1.A.3b| | 1 |
Rear reflector excessively damaged so that its function is impaired |1.5.1c| | 1 |
Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Rear wheel bearing has excessive play |2.6.2| | 1 |
Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Offside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Offside Rear Drive shaft joint so worn it is likely to fail (6.1.7 (c) (ii)) | 1 |
Nearside Rear Shock absorbers has a serious fluid leak | 1 |
Offside Rear Shock absorbers has a serious fluid leak | 1 |
Nearside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Offside Front Lower Suspension arm attachment bracket/mounting insecure and impairing directional stability bolt/fixing missing (5.3.3 (a) (ii)) | 1 |
Nearside Front Sub-frame pin or bush likely to become detached (5.3.4 (a) (ii)) | 1 |
Hazard warning lamps inoperative (4.4.1 (e)) | 1 |
Nearside Front Anti-roll bar linkage fractured |2.4.G.1| | 1 |
Offside Front Anti-roll bar linkage fractured |2.4.G.1| | 1 |
Offside Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
Brake fluid significantly below minimum mark (1.1.10 (d) (ii)) | 1 |
Exhaust has a major leak of exhaust gases Front flexi (6.1.2 (a)) | 1 |
Nearside Rear Suspension component mounting prescribed area is inadequately repaired End of sill not repaired with full welds and can still see some corrosion below (5.3.6 (a) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inside wheel arch (5.3.6 (a) (i)) | 1 |
Offside Vehicle structure strengthening plate or fastening so insecure that structural rigidity is seriously reduced central under sill/floor corroded by seatbelt anchor |6.1.1 |b| |ii|| | 1 |
Nearside Rear Vehicle structure strengthening plate or fastening so insecure that structural rigidity is seriously reduced under sill to floor corroded |6.1.1 |b| |ii|| | 1 |
Indicator switch faulty on left hand operation |1.4.A.1| | 1 |
Emissions not tested tick over to high |7.3.A.1| | 1 |
Offside Front Upper Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Rear Mechanical brake component has restricted free movement | 1 |
Offside Inner Steering pivot point has excessive play |2.2.B.1g| | 1 |
Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Nearside Front Upper Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Front Lower Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
Nearside Rear Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Jacking point missing (6.1.1 (c) (i)) | 1 |
Nearside Front Outer Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Rear Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting arch to chassis (6.2.2 (d) (i)) | 1 |
Nearside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
Offside Rear Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Steering arm has relative movement at its fixings |2.2.B.1h| | 1 |
Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Front Fuel pipe leaking (6.1.3 (b) (i)) | 1 |
Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Offside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
Nearside Front Steering pivot point has excessive play |2.2.B.1g| | 1 |
Nearside Rear Lower Radius arm has excessive play in a pin/bush |2.4.G.2| | 1 |
Offside Drag link end ball pin shank loose |2.2.B.1c| | 1 |
Offside Outer Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Front Seat belt insecurely fixed to the vehicles structure |5.2.1a| | 1 |
Offside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
Nearside Rear Shock absorber has negligible damping effect |2.7.5| | 1 |
Nearside Front Lower Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Offside Front Sub-frame locating pin locking device not properly locked |2.4.G.3b| | 1 |
Nearside Front Anti-roll bar attachment bracket/mounting fractured |2.4.G.1| | 1 |
Offside Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Centre Rear Brake pipe inadequately clipped |3.6.B.1| | 1 |
Nearside Front Sub-frame rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Offside Front Sub-frame rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Nearside Outer Seat belt anchorage prescribed area is inadequately repaired sill |5.2.6| | 1 |
Offside Outer Seat belt anchorage prescribed area is inadequately repaired sill |5.2.6| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded crossmember |2.4.A.3| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded crossmember |2.4.A.3| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded under arch |2.4.A.3| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded under arch |2.4.A.3| | 1 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded chassis/floor |2.4.A.3| | 1 |
Offside Rear Suspension component mounting prescribed area is excessively corroded floor/chassis |2.4.A.3| | 1 |
Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Rear Suspension component mounting prescribed area is inadequately repaired sill needs seam welding |2.4.A.3| | 1 |
Offside Rear Suspension component mounting prescribed area is inadequately repaired sill needs seam welding |2.4.A.3| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded inner weel arch and 30cm from the anti role bar |2.4.A.3| | 1 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Position lamp not working (4.2.1 (a) (ii)) | 1 |
Offside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Nearside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting sill (6.2.2 (d) (i)) | 1 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength boot floor (5.3.6 (a) (i)) | 1 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner (5.3.6 (a) (i)) | 1 |
Nearside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
Offside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
Nearside Front Service brake excessively binding (1.2.1 (f)) | 1 |
Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
Offside Front Floor excessively deteriorated |6.2.4 |a| |i|| | 1 |
Nearside Front Wheel bearing has excessive play |5.1.3 |a| |i|| | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
Centre Front Parking brake lever has no reserve travel |3.1.6b| | 1 |
Nearside Rear Sub-frame insecure |2.4.G.1| | 1 |
Nearside Rear Sub-frame attachment rubber mounting deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Rear Emissions not tested |7.0| | 1 |
Nearside Rear wheel bearing has excessive play |2.6.2| | 1 |
Nearside Front Lower Suspension component ball joint dust cover missing |5.3.4 |b| |ii|| | 1 |
Power steering fluid reservoir empty |2.1.5 |b| |ii|| | 1 |
Nearside Front position lamp|s| flickers when tapped lightly by hand |1.1.4c| | 1 |
Nearside Rear Wheel nut|s| missing |4.2.A.1e| | 1 |
Offside Front Wheel nut|s| missing |4.2.A.1e| | 1 |
Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
Nearside Rear Seat belt retracting mechanism defective |5.2.5b| | 1 |
Exhaust engine idle speed too high |7.3.A.2a| | 1 |
Offside Rear Stop lamp not working |1.2.1b| | 1 |
Nearside Headlamp adversely affected by the operation of another lamp |1.7.5c| | 1 |
Offside Headlamp adversely affected by the operation of another lamp |1.7.5c| | 1 |
Offside Rear Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
Nearside Rear Suspension arm has excessive play in a pin/bush |2.4.G.2| | 1 |
Exhaust emissions carbon monoxide content excessive |8.2.1.2 |b|| | 1 |
Dipswitch does not operate immediately when selected on main beam |4.1.3 |b|| | 1 |
Nearside Rear fog lamp excessively deteriorated so that it is not visible from a reasonable distance |1.3.2d| | 1 |
Rear Stop lamp not working |1.2.1b| | 1 |
Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear fog lamp missing |1.3.2a| | 1 |
Nearside Front front brake binding |3.7.B.1| | 1 |
Nearside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Exhaust has a part missing |7.1.1a| | 1 |
Nearside Parking brake recording little or no effort |3.7.D.3a| | 1 |
Service brake: efficiency below requirements |3.7.D.4| | 1 |
Parking brake: efficiency below requirements |3.7.D.4| | 1 |
Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
Offside Rear Brake hose excessively damaged cut. (1.1.12 (b) (ii)) | 1 |
Dipswitch operation does not extinguish all main beam headlamps leaving at least one pair of dipped beam headlamps (4.1.3 (b)) | 1 |
Dipswitch operation does not deflect all main beam headlamps to make them dipped beams (4.1.3 (b)) | 1 |
Nearside Front Lower Front suspension ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Offside Rear position lamp|s| not working |1.1.A.3b| | 1 |
Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings Boot floor to inner wing |6.1.B.2| | 1 |
Nearside Front Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings Inner Sill |6.1.B.2| | 1 |
Offside Front Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings Inner Sill |6.1.B.2| | 1 |
Offside Front Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wing panel to floor |6.1.B.2| | 1 |
Steering box insecure |2.2.B.1a| | 1 |
Front Anti-roll bar rubber bush deteriorated resulting in excessive movement anti roll D bushes |2.4.G.2| | 1 |
Offside Front Lower Suspension arm rubber bush bonding deteriorated resulting in excessive movement both inner bushes of lower arm |2.4.G.2| | 1 |
Exhaust system not adequately supported |7.1.1| | 1 |
Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Offside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
Nearside Front Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front Body or chassis is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Rear Body or chassis is cracked, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Nearside Front engine mounting bracket insecure and likely to fail |6.1.D.1b| | 1 |
Dipswitch operation does not extinguish all main beam headlamps leaving at least one pair of dipped beam headlamps |1.7.4b| | 1 |
Offside Front Valve stem seriously misaligned |4.1.D.1e| | 1 |
Offside Front Upper Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
Nearside Front Anti-roll bar linkage cracked |2.4.G.1| | 1 |
Nearside Front Anti-roll bar linkage insecure |2.4.G.1| | 1 |
Power steering pump drive system defective |2.3.6| | 1 |
Nearside Rear Shock absorber has an excessively worn bush rear most shock absorber |2.7.4| | 1 |
Offside Front Upper Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
Nearside Rear Lower Shock absorber has an excessively worn bush |2.7.4| | 1 |
Nearside Front Statutory seat belt missing catch mechanism |5.1.1| | 1 |
Ball joint has excessive play joint connected to steering box drop arm. |2.2.B.1f| | 1 |
Offside Rear Shock absorber has a serious fluid leak front shocker |2.7.3| | 1 |
Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
Fuel pipe leaking |7.2.3| | 1 |