| Most common failures | No# failures |
|---|
| Brake pipe excessively corroded | 24 |
| Windscreen wiper does not clear the windscreen effectively | 14 |
| Headlamp aim out of alignment | 10 |
| Registration plate lamp issues | 9 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Horn not working |1.6.2a| | 4 |
| Nearside Front Direction indicator incorrect colour |1.4.A.2f| | 4 |
| Offside Rear Stop lamp not working |1.2.1b| | 3 |
| Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 3 |
| Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 3 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Stop lamp not working |1.2.1b| | 2 |
| Offside Front Direction indicator incorrect colour |1.4.A.2f| | 2 |
| Nearside Rear Stop lamp not working |1.2.1b| | 2 |
| Nearside Rear Direction indicator not working |1.4.A.2c| | 2 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Brake load sensing valve seized |3.6.E.3| | 2 |
| Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 2 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 2 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Parking brake: efficiency below requirements |3.7.B.7| | 2 |
| Fuel cap/sealing device ineffective (6.1.3 (b) (i)) | 2 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 2 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 2 |
| Brakes imbalanced across an axle | 2 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Registration plate issues | 2 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Windscreen has damage | 2 |
| Centre Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Nearside Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
| Offside Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting CHASSIS RAIL |6.2.2 |d| |i|| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting INNER WING PANEL, THROUGH INTO ENGINE COMPARTMENT |6.2.2 |d| |i|| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting ADJACENT TO JACKING POINT OUT RIGGER |6.2.2 |d| |i|| | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting JACKING POINT OUT RIGGER |6.2.2 |d| |i|| | 1 |
| Offside Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting OUTER SILL PANEL |6.2.2 |d| |i|| | 1 |
| Nearside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting FORWARD OF FRONT WHEEL, ADJACENT TO OUT RIGGER |6.2.2 |d| |i|| | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting INNER SILL PANEL, CLOSING PANEL |6.2.2 |d| |i|| | 1 |
| Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting WHEEL ARCH (6.2.2 (d) (i)) | 1 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting WHEEL ARCH (6.2.2 (d) (i)) | 1 |
| Brake servo insecurely mounted lower bolts insecure |3.6.A.2a| | 1 |
| Offside Front Brake prescribed area is excessively damaged under wheel arch near flexy hose mount (1.1.21 (e) (i)) | 1 |
| Nearside Rear Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Upper Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Steering lock fails to engage |2.1.4b| | 1 |
| Nearside Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
| Offside Rear Rear wheel bearing has excessive play |2.6.2| | 1 |
| Service brake efficiency below requirements |1.2.2 |a| |i|| | 1 |
| Parking brake efficiency less than 50% of the required value |1.4.2 |a| |ii|| | 1 |
| Nearside Rear Parking brake inoperative on one side |1.4.1 |a|| | 1 |
| Offside Rear Parking brake inoperative on one side |1.4.1 |a|| | 1 |
| Nearside Rear Service brake effort inadequate at a wheel |1.2.1 |a| |i|| | 1 |
| Offside Rear Service brake effort inadequate at a wheel |1.2.1 |a| |i|| | 1 |
| Nearside Rear Service brake excessively binding |1.2.1 |f|| | 1 |
| Offside Rear Service brake excessively binding |1.2.1 |f|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 1 |
| Parking brake lever has excessive movement indicating incorrect adjustment |1.1.6 |c|| | 1 |
| Brake pedal anti-slip provision incomplete |3.3.A.1b| | 1 |
| Offside Front Windscreen has a combination of minor damage areas which restrict the drivers view |8.3.1c| | 1 |
| Nearside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Nearside Front Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Offside Front Exhaust mounting missing |7.1.1b| | 1 |
| Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Rear wheel bearing has excessive play |2.6.2| | 1 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Rear brake application uneven | 1 |
| Nearside Front Direction indicator flashing more than 120 times a minute |1.4.A.2g| | 1 |
| Nearside Side repeater flashing more than 120 times a minute |1.4.A.2g| | 1 |
| Nearside Rear Body has a sharp edge caused by damage light cluster |6.1.C.1| | 1 |
| Nearside Stop lamp emits other than a steady red light |1.2.1e| | 1 |
| Brake valve leaking compensator |3.6.A.1| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 1 |
| Offside Front Brake hose excessively damaged |3.6.B.4d| | 1 |
| Offside Front Brake pipe inadequately supported |3.6.B.1| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded inner arch under battery |2.4.A.3| | 1 |
| Offside Ball joint has excessive play |2.2.B.1f| | 1 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Suspension component mounting prescribed area is excessively corroded inner sills |2.4.A.3| | 1 |
| Nearside Front Side repeater not working |1.4.A.2c| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Rear reflector insecure |1.5.1a| | 1 |
| Offside Front Sub-frame attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Brake valve leaking |3.6.A.1| | 1 |
| Nearside Front Front constant velocity joint is insecure |2.5.C.1b| | 1 |
| Nearside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Offside Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded OUTER SILL |5.2.6| | 1 |
| Offside Rear Suspension spring mounting prescribed area is excessively corroded OUTER SILL AREA |2.4.A.3| | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Windscreen washer not working | 1 |
| Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Stop lamp not working |1.2.1b| | 1 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 1 |
| Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 1 |
| Central Exhaust system insecure rubber mount broken (6.1.2 (a)) | 1 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
| Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Central Exhaust system not adequately supported |7.1.1| | 1 |
| Front Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing &top mount |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength top mount & inner wing |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength spring mount |5.3.6 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 1 |
| Suspension component mounting prescribed area is excessively corroded rear panel |2.4.A.3| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Seat belt damaged sufficient to obstruct correct operation of the belt |5.2.2a| | 1 |
| Rear Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Offside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Inner Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Outer Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Brake hose excessively deteriorated | 1 |
| Steering system excessively tight |2.2.D.1| | 1 |
| Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Rear brake binding | 1 |
| Emissions not tested |7.0| | 1 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Front Horn not working |1.6.2a| | 1 |
| Offside Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Direction indicators not working |1.4.A.2c| | 1 |
| Nearside Rear Direction indicators incorrect colour |1.4.A.2f| | 1 |
| Offside Rear Direction indicators incorrect colour |1.4.A.2f| | 1 |
| Offside Front Outer Front constant velocity joint is insecure |2.5.C.1b| | 1 |
| Power steering pipe|s| or hose|s| leaking |2.3.3b| | 1 |
| Nearside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings arch by engine mount |6.1.B.2| | 1 |
| Offside Front Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings arch under battery mount |6.1.B.2| | 1 |
| Offside Front Outer Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill |6.1.B.2| | 1 |
| Nearside Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings front to rear sill |6.1.B.2| | 1 |
| Nearside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings arch by shock mount |6.1.B.2| | 1 |
| Nearside Front Upper Suspension spring mounting prescribed area is excessively corroded strut mount |2.4.A.3| | 1 |
| Offside Front Upper Suspension spring mounting prescribed area is excessively corroded strut mount |2.4.A.3| | 1 |
| Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Horn not working (7.7 (a) (ii)) | 1 |
| Statutory seat belt missing |5.1.1| | 1 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Service brake lagging in operation (1.2.1 (d)) | 1 |
| Headlamp levelling device inoperative (4.1.5 (a)) | 1 |
| Suspension component mounting prescribed area is inadequately repaired rear valance within 30cm of rear spring mounts (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear valance within 30cm of rear spring mounts (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength nearside outer sill , inner sill/chassis within 30cm of rear spring mount (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength offside rear inner sill/chassis within 30cm of spring mount (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength offside & nearside front chassis within 30cm of front subframe mount. (5.3.6 (a) (i)) | 1 |
| Suspension component mounting prescribed area excessively corroded significantly reducing structural strength nearside front inner wing/integral body panel within 30cm of front subframe mount . (5.3.6 (a) (i)) | 1 |
| Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Brake hose damaged | 1 |
| Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |