| Most common failures | No# failures |
|---|
| Headlamp aim out of alignment | 264 |
| Brake pipe excessively corroded | 142 |
| Registration plate lamp issues | 87 |
| Windscreen wiper does not clear the windscreen effectively | 86 |
| Nearside Headlamp insecure |1.7.3| | 77 |
| Brakes imbalanced across an axle | 77 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 68 |
| Nearside Side repeater not working |1.4.A.2c| | 60 |
| Offside Headlamp insecure |1.7.3| | 55 |
| Offside Side repeater not working |1.4.A.2c| | 54 |
| Service brake: efficiency below requirements |3.7.B.7| | 48 |
| Offside Rear fog lamp not working |1.3.2b| | 39 |
| Brake hose excessively deteriorated | 39 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 39 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 38 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 38 |
| Nearside Stop lamp not working |1.2.1b| | 35 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 33 |
| Parking brake: efficiency below requirements |3.7.B.7| | 30 |
| Horn not working |1.6.2a| | 28 |
| Rear brake binding | 28 |
| Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 27 |
| Nearside Front Headlamp insecure |1.7.3| | 26 |
| Battery insecure |1.9.1| | 24 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 24 |
| Rear parking brake recording little or no effort | 24 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 22 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 22 |
| Brake load sensing valve linkage seized |3.6.E.3| | 22 |
| Nearside Front Side repeater not working |1.4.A.2c| | 21 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 21 |
| Offside Stop lamp not working |1.2.1b| | 21 |
| Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 21 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 20 |
| Rear brake application uneven | 20 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 18 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 18 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 18 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 18 |
| Offside Front Headlamp insecure |1.7.3| | 18 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 17 |
| Offside Track rod end ball joint has excessive play |2.2.B.1f| | 16 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 16 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 16 |
| Offside Front Side repeater not working |1.4.A.2c| | 15 |
| Rear fog lamp not working |1.3.2b| | 14 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 14 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 14 |
| Front brake application uneven | 14 |
| Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 14 |
| Offside front brake binding |3.7.B.1| | 14 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 13 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 13 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 13 |
| Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 13 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 13 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 12 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 12 |
| Brake load sensing valve seized |3.6.E.3| | 12 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 12 |
| Front brake disc in such a condition that it is seriously weakened | 12 |
| Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 11 |
| Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 11 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 11 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 11 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 11 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 10 |
| Registration plate issues | 10 |
| Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 10 |
| Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 10 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 10 |
| Hazard warning switch faulty |1.4.B.1d| | 10 |
| Rear fog lamp tell tale not working |1.3.1b| | 10 |
| Rear Exhaust system not adequately supported |7.1.1| | 10 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 9 |
| Offside Rear wheel bearing rough when rotated |2.6.1| | 9 |
| Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 9 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 9 |
| Parking brake lever has no reserve travel |3.1.6b| | 9 |
| Offside Front front brake binding |3.7.B.1| | 9 |
| Nearside front brake binding |3.7.B.1| | 9 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 9 |
| Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 9 |
| Rear Exhaust mounting missing |7.1.1b| | 9 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 8 |
| Nearside Rear Stop lamp not working |1.2.1b| | 8 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 8 |
| Nearside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 8 |
| Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 8 |
| Nearside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 8 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
| Hazard warning lamps inoperative |1.4.B.1b| | 8 |
| Offside Headlamp insecure (4.1.1 (c)) | 8 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 8 |
| Nearside Rear Direction indicator not working |1.4.A.2c| | 8 |
| Nearside Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 8 |
| Windscreen washer not working | 8 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 8 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 8 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 8 |
| Nearside Headlamp insecure (4.1.1 (c)) | 8 |
| Headlamp insecure |1.7.3| | 8 |
| Offside Headlamp not working on main beam |1.7.5a| | 7 |
| Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 7 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 7 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 7 |
| Front Windscreen wiper not operating automatically when switched on |8.2.1b| | 7 |
| Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 7 |
| Nearside Headlamp aim beam image kick up to the offside |1.8| | 7 |
| Nearside Front Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 7 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 7 |
| Nearside Rear wheel bearing rough when rotated |2.6.1| | 6 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 6 |
| Mechanical brake component has restricted free movement | 6 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 6 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 6 |
| Offside Headlamp aim beam image kick up to the offside |1.8| | 6 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 6 |
| Offside Rear position lamp|s| not working |1.1.A.3b| | 6 |
| Rear Brake load sensing valve linkage seized |3.6.E.3| | 6 |
| Service brake efficiency below requirements |1.2.2 |a| |i|| | 6 |
| Offside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 6 |
| Nearside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 5 |
| Nearside Rear Radius arm has excessive play in a pin/bush |2.4.G.2| | 5 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 5 |
| Nearside Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 5 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 5 |
| Rear Brake load sensing valve seized |3.6.E.3| | 5 |
| Fuel pipe leaking |7.2.3| | 5 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 5 |
| Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 5 |
| Direction indicators not working |1.4.A.2c| | 5 |
| Offside Front brake disc excessively pitted |3.5.1h| | 5 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 5 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 5 |
| Headlamp aim not tested |1.8.A.1c| | 5 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 5 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 5 |
| Exhaust system not adequately supported |7.1.1| | 5 |
| Emissions not tested |7.0| | 5 |
| Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
| Nearside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 5 |
| Offside Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 5 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 5 |
| Rear Stop lamp not working |1.2.1b| | 5 |
| Offside Rear Stop lamp not working |1.2.1b| | 5 |
| Offside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Offside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 5 |
| Nearside Side repeater not working (4.4.1 (a) (ii)) | 5 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 5 |
| Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 5 |
| Nearside Front coil spring fractured |2.4.C.1a| | 5 |
| Nearside Side repeater insecure |1.4.A.2b| | 4 |
| Offside Front Front wheel bearing rough when rotated |2.5.A.2| | 4 |
| Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 4 |
| Nearside Headlamp not working on main beam |1.7.5a| | 4 |
| Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Offside Front Direction indicator incorrect colour |1.4.A.2f| | 4 |
| Offside Rear Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 4 |
| Nearside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 4 |
| Brake pedal has no servo assistance |3.3.B.2| | 4 |
| Rear Exhaust has a part missing |7.1.1a| | 4 |
| Nearside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 4 |
| Rear fog lamp switch faulty |1.3.1a| | 4 |
| Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 4 |
| Nearside Side repeater not working |4.4.1 |a| |ii|| | 4 |
| Offside Side repeater not working |4.4.1 |a| |ii|| | 4 |
| Brake pedal spongy |3.3.B.1b| | 4 |
| Offside Front wheel bearing rough when rotated |2.5.A.2| | 4 |
| Nearside Rear Rear position lamp|s| not working |1.1.A.3b| | 4 |
| Offside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 4 |
| Nearside Front front brake binding |3.7.B.1| | 4 |
| Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Hazard warning switch inoperative (4.4.2 (a) (ii)) | 4 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 4 |
| Nearside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 4 |
| Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Brake valve leaking |3.6.A.1| | 4 |
| Offside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 4 |
| Brake performance not tested |3.7.A.1| | 4 |
| Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
| Offside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 4 |
| Nearside Front Headlamp insecure (4.1.1 (c)) | 4 |
| Brake load sensing valve seized and ABS not fitted or inoperative (1.1.17 (c) (ii)) | 4 |
| Fuel system component leaking |7.2.3| | 4 |
| Nearside Body has a sharp edge caused by corrosion |6.1.C.1| | 4 |
| Offside Body has a sharp edge caused by corrosion |6.1.C.1| | 4 |
| Offside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 4 |
| Offside Rear Rear position lamp|s| not working |1.1.A.3b| | 4 |
| Nearside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 4 |
| Nearside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 4 |
| Rear Rear fog lamp not working |1.3.2b| | 4 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 4 |
| Nearside Front Headlamp not working on main beam |1.7.5a| | 4 |
| Nearside Side repeater missing |1.4.A.2b| | 4 |
| Offside Side repeater missing |1.4.A.2b| | 4 |
| Brake pedal anti-slip provision missing |3.3.A.1b| | 4 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 4 |
| Nearside Front Suspension arm has excessive play in a pin/bush |2.4.G.2| | 4 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Offside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 4 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 4 |
| Nearside Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 3 |
| Nearside Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 3 |
| Rear Brake valve leaking |3.6.A.1| | 3 |
| Nearside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Brake pedal has insufficient reserve movement |3.3.A.5| | 3 |
| Front Exhaust has part of the system excessively deteriorated |7.1.1a| | 3 |
| Offside Front Headlamp aim beam image kick up to the offside |1.8| | 3 |
| Offside Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Front Ball joint has excessive play |2.2.B.1f| | 3 |
| Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Front Headlamp insecure (4.1.1 (c)) | 3 |
| Nearside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 3 |
| Offside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 3 |
| Offside Front Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 3 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 3 |
| Horn not working (7.7 (a) (ii)) | 3 |
| Offside Front Direction indicator not working |1.4.A.2c| | 3 |
| Windscreen has a sticker or other obstruction encroaching by more than 10mm within zone `A` |8.3.1b| | 3 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded sill |2.4.A.3| | 3 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 3 |
| Nearside Side repeater incorrect colour |1.4.A.2f| | 3 |
| Offside Front Lower Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 3 |
| Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 3 |
| Offside Outer Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Windscreen wiper blade insecure | 3 |
| Brake pedal creeps down when held under pressure |3.3.B.1a| | 3 |
| Brake load sensing valve linkage defective and function impaired |3.6.E.3| | 3 |
| Offside front brake juddering severely |3.7.A.2b| | 3 |
| Parking brake: efficiency below requirements |3.7.C.1b| | 3 |
| Offside Rear Subframe mounting prescribed area is inadequately repaired |2.4.A.3| | 3 |
| Stop lamp remains on when the brakes are released | 3 |
| Offside Front coil spring incomplete |2.4.C.1a| | 3 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 3 |
| Nearside Front Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 3 |
| Offside Front Direction indicator insecure |1.4.A.2b| | 3 |
| Offside Front Service brake excessively binding |1.2.1 |f|| | 3 |
| Nearside Front Front position lamp|s| insecure |1.1.A.3a| | 3 |
| Offside Front Front position lamp|s| insecure |1.1.A.3a| | 3 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 3 |
| Driver`s seat insecure |6.2.A.1| | 3 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
| Offside Rear Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 3 |
| Centre Exhaust system not adequately supported |7.1.1| | 3 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 3 |
| Offside Front Ball joint has excessive play |2.2.B.1f| | 3 |
| Offside Rear Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Nearside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 3 |
| Offside Front Headlamp not working on main beam |1.7.5a| | 3 |
| Windscreen wiper not operating automatically when switched on |8.2.1b| | 3 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 3 |
| Brake hose has insufficient room to move | 3 |
| Offside Rear Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 3 |
| Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 3 |
| Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 3 |
| Offside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 3 |
| Offside Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 3 |
| Offside Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 3 |
| Nearside Front wheel bearing rough when rotated |2.5.A.2| | 3 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 3 |
| Nearside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 3 |
| Windscreen has damage | 3 |
| Nearside Front Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt (6.1.7 (g) (ii)) | 3 |
| Nearside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 3 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 3 |
| Offside Front coil spring fractured |2.4.C.1a| | 3 |
| Rear Mechanical brake component has restricted free movement | 3 |
| Offside Front coil spring broken |2.4.C.1a| | 3 |
| Offside Front Lower Suspension arm has excessive play in a pin/bush |2.4.G.2| | 3 |