| Most common failures | No# failures |
|---|
| Headlamp aim out of alignment | 31 |
| Brake pipe excessively corroded | 18 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 16 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 11 |
| Windscreen wiper does not clear the windscreen effectively | 10 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 10 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 10 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 10 |
| Rear brake binding | 8 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 7 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 7 |
| Offside Front wheel bearing rough when rotated |2.5.A.2| | 7 |
| Rear parking brake recording little or no effort | 7 |
| Registration plate lamp issues | 6 |
| Offside Headlamp insecure |1.7.3| | 6 |
| Brakes imbalanced across an axle | 6 |
| Offside Rear fog lamp not working |1.3.2b| | 6 |
| Nearside Side repeater not working |1.4.A.2c| | 5 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 5 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 5 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 5 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Rear brake application uneven | 4 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Nearside front brake binding |3.7.B.1| | 4 |
| Nearside Headlamp insecure |1.7.3| | 4 |
| Service brake: efficiency below requirements |3.7.B.7| | 4 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 4 |
| Offside Stop lamp not working |1.2.1b| | 4 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
| Parking brake: efficiency below requirements |3.7.B.7| | 4 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Nearside Front Side repeater not working |1.4.A.2c| | 3 |
| Offside Track rod end ball joint has excessive play |2.2.B.1f| | 3 |
| Brake hose excessively deteriorated | 3 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 3 |
| Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Indicator tell tale inoperative |1.4.A.2a| | 3 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 3 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 3 |
| Offside Front Headlamp insecure |1.7.3| | 3 |
| Brake load sensing valve linkage seized |3.6.E.3| | 3 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 3 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 3 |
| Rear Brake load sensing valve seized |3.6.E.3| | 2 |
| Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
| Offside Front Direction indicator not working |1.4.A.2c| | 2 |
| Rear Exhaust system not adequately supported |7.1.1| | 2 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
| Nearside Front Upper Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Rear Brake valve leaking |3.6.A.1| | 2 |
| Nearside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Front Steering rack gaiter split |2.2.D.2d| | 2 |
| Offside Rear Stop lamp not working |1.2.1b| | 2 |
| Front Windscreen wiper blade missing |8.2.2| | 2 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 2 |
| Windscreen washer not working | 2 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 2 |
| Rear fog lamp tell tale not working |1.3.1b| | 2 |
| Offside Front Electrical wiring insecure |1.9.2a| | 2 |
| Offside front brake binding |3.7.B.1| | 2 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Nearside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 2 |
| Rear Brake load sensing valve linkage seized |3.6.E.3| | 2 |
| Fuel system component leaking |7.2.3| | 2 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 2 |
| Offside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 2 |
| Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 2 |
| Battery insecure |1.9.1| | 2 |
| Nearside Stop lamp not working |1.2.1b| | 2 |
| Offside Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Horn not working |1.6.2a| | 2 |
| Headlamp switch faulty |1.7.1| | 2 |
| Nearside Headlamp insecure (4.1.1 (c)) | 2 |
| Offside Headlamp insecure (4.1.1 (c)) | 2 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Track rod end ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
| rear brakes release unevenly |3.7.B.4| | 1 |
| Nearside Steering arm has relative movement at its fixings |2.2.B.1h| | 1 |
| Offside Steering arm has relative movement at its fixings |2.2.B.1h| | 1 |
| Rear fog lamp not working |1.3.2b| | 1 |
| Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Nearside Rear Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Fuel system component insecure |7.2.1| | 1 |
| Nearside Front Direction indicator not working |1.4.A.2c| | 1 |
| Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
| Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Brake valve leaking |3.6.A.1| | 1 |
| Nearside Front Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Front Driver`s door does not latch securely closed |6.2.B.1a| | 1 |
| Offside Front Upper Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Inner Front Upper Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Inner Front Upper Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Front Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 1 |
| Rear Brake hydraulic reservoir leaking hydraulic fluid |3.6.A.1| | 1 |
| Offside Front Lower Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Outer Upper Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Outer Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Emissions not tested |7.0| | 1 |
| Brake performance not tested |3.7.A.1| | 1 |
| Offside Rear Shock absorber insecure |2.7.2b| | 1 |
| Nearside Rear Shock absorber detached |2.7.2b| | 1 |
| Nearside Front Headlamp not in good working order |not working| |1.2.4a| | 1 |
| Nearside Rear Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings inner,door,piller |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings x2 |6.1.B.2| | 1 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front front brake binding |3.7.B.1| | 1 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Nearside Front Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Stop lamp(s) remains on when the brakes are released (4.3.2 (a) (iii)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Inner Wing |5.3.6 |a| |i|| | 1 |
| Offside Outer Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Outer Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Outer Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Rear Parking brake mechanism/associated mounting prescribed area is excessively corroded |3.1.9| | 1 |
| Nearside Obligatory mirror missing |8.1.1| | 1 |
| Offside Obligatory mirror insecure |8.1.1| | 1 |
| Front Headlamp insecure |1.7.3| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Inner Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Front Suspension spring mounting prescribed area is deliberately modified which significantly reduces the original strength |2.4.A.3| | 1 |
| Offside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 1 |
| Horn not working intermittent and not very loud when it does work |1.6.2a| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering chassis leg area |6.1.A.1| | 1 |
| Steering column flexible coupling is excessively deteriorated has a few splits in it |2.1.5| | 1 |
| Fuel pipe insecure front end of front to rear pipe insecure |7.2.1| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded end of sill requires welding its filling the sill up with water |5.2.6| | 1 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded end of sill requires weldinjg |2.4.A.3| | 1 |
| Offside Rear Subframe mounting prescribed area is excessively corroded end of sill requires welding |2.4.A.3| | 1 |
| Steering column flexible coupling is excessively deteriorated |2.1.5| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded INNER WING STRUT TOP AREA |2.4.A.3| | 1 |
| Nearside Front Track rod end ball pin shank loose |2.2.B.1c| | 1 |
| Nearside Seat belt anchorage prescribed area is excessively corroded OUTER SILL REQUIRES WELDING IN SEVERAL PLACES |5.2.6| | 1 |
| Rear Exhaust system not adequately supported SILENCER |7.1.1| | 1 |
| Nearside Rear Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Front front brake binding |3.7.B.1| | 1 |
| Nearside Rear front brake binding |3.7.B.1| | 1 |
| Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 1 |
| Front brake application uneven | 1 |
| Nearside Front Headlamp insecure |1.7.3| | 1 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 1 |
| Offside Rear Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Offside Rear Suspension component mounting prescribed area is fractured |2.4.A.3| | 1 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Centre Rear Brake valve leaking |3.6.A.1| | 1 |
| Front Fuel pipe insecure |7.2.1| | 1 |
| Brake has no servo assistance |3.3.B.2| | 1 |
| Offside Rear Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Offside Rear Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
| Nearside Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Electrical wiring insecure |1.9.2a| | 1 |
| Offside Front Front constant velocity joint is excessively worn |2.5.C.1b| | 1 |
| Front brake excessively fluctuating | 1 |
| Centre Front Fuel system component insecure |7.2.1| | 1 |
| Nearside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Front Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
| Nearside Front Parking brake mechanism/associated mounting prescribed area is excessively corroded |3.1.9| | 1 |
| Offside Front Parking brake mechanism/associated mounting prescribed area is excessively corroded |3.1.9| | 1 |
| Front Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Brake fluid significantly below minimum mark (1.1.10 (d) (ii)) | 1 |
| Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
| Offside Front Drivers view of the road through the swept area of the windscreen significantly affected by an obstruction wipers stop (3.1 (a) (ii)) | 1 |
| Nearside Front Headlamp reflector seriously defective (4.1.1 (b) (ii)) | 1 |
| Nearside Front Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 1 |
| Nearside Rear Fuel cap/sealing device ineffective (6.1.3 (b) (i)) | 1 |
| Fuel pipe insecure under car (6.1.3 (a) (i)) | 1 |
| Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to inner sill (6.1.1 (c) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to chassis (6.1.1 (c) (i)) | 1 |
| Nearside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis near brake hose (6.1.1 (c) (i)) | 1 |
| Offside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced near brake hose (6.1.1 (c) (i)) | 1 |
| Brake pedal anti-slip provision missing |3.3.A.1b| | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Nearside Rear reflector excessively deteriorated so that its function is impaired |1.5.1c| | 1 |
| Brake hose has insufficient room to move | 1 |
| Offside Rear Subframe mounting prescribed area is inadequately repaired Front mountiing |5.3.6 |a| |i|| | 1 |
| Lower Steering column flexible coupling is excessively deteriorated |2.2.2 |c|| | 1 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Stop lamp|s| remains on when the brakes are released |4.3.2 |a| |iii|| | 1 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded offside front of bulk head/inner wing panel |3.6.C.3| | 1 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded offside front of bulk head |3.6.C.3| | 1 |
| Suspension component mounting prescribed area is excessively corroded offside front of bulk head/inner wing panel |2.4.A.3| | 1 |
| Suspension component mounting prescribed area is excessively corroded offside front of bulk head |2.4.A.3| | 1 |
| Suspension component mounting prescribed area is excessively corroded nearside front of bulk head/inner wing panel behind coolant tank |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded chassis rail in front of lower engine mount |2.4.A.3| | 1 |
| Offside Rear Inner Subframe mounting prescribed area is excessively corroded wheel arch |2.4.A.3| | 1 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded wheel arch x2 |2.4.A.3| | 1 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Centre Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
| Nearside Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Seat belt retracting mechanism defective |5.2.5b| | 1 |
| Brake pedal has insufficient reserve movement |3.3.A.5| | 1 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 1 |
| Offside Outer Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Inner Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Electrical wiring deteriorated, likely to cause a short |1.9.2b| | 1 |
| Fuel pipe leaking |7.2.3| | 1 |
| Offside Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Centre Brake pipe inadequately supported |3.6.B.1| | 1 |
| Nearside Rear Stop lamp not working |1.2.1b| | 1 |
| Brake pedal spongy |3.3.B.1b| | 1 |
| Registration plate issues | 1 |
| Lower Steering column flexible coupling is excessively deteriorated |2.1.5| | 1 |
| Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Brake pipe connection leaking on a hydraulic braking system (1.1.11 (b) (ii)) | 1 |
| Offside Rear Direction indicators not working |1.4.A.2c| | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 1 |
| Offside Front coil spring fractured |2.4.C.1a| | 1 |
| Offside Front coil spring corroded so that its cross sectional area is reduced and seriously weakened |2.4.C.1b| | 1 |
| Nearside Inner Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Fuel pipe insecure |7.2.1| | 1 |
| Brake load sensing valve seized |3.6.E.3| | 1 |
| Offside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Windscreen wiper not operating automatically when switched on motor or stalk |8.2.1b| | 1 |
| Brake fluid warning lamp illuminated |3.6.G.2| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wheel arch |6.1.B.2| | 1 |
| Nearside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings centre floor |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings centre floor |6.1.B.2| | 1 |
| Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings centre chassis |6.1.B.2| | 1 |
| Offside Rear Vehicle structure has an inadequate repair, seriously affecting its strength within 30cm of the body mountings inner wheel arch
|6.1.B.2| | 1 |
| Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
| Offside Inner Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced lower mount area outer sill |7.1.1 |a| |i|| | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced under sill |7.1.1 |a| |i|| | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced sill |7.1.1 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength sill |5.3.6 |a| |i|| | 1 |
| Fuel tank leaking excessively or a risk of fire |6.1.3 |b| |ii|| | 1 |
| Service brake efficiency below requirements |1.2.2 |a| |i|| | 1 |
| Parking brake efficiency less than 50% of the required value |1.4.2 |a| |ii|| | 1 |
| Nearside Rear Parking brake inoperative on one side |1.4.1 |a|| | 1 |
| Offside Rear Parking brake inoperative on one side |1.4.1 |a|| | 1 |
| Nearside Rear Service brake has no recorded effort at a wheel |1.2.1 |a| |ii|| | 1 |
| Offside Rear Service brake has no recorded effort at a wheel |1.2.1 |a| |ii|| | 1 |
| Centre Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Exhaust engine idle speed too high |7.3.A.2a| | 1 |
| Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Rear fog lamp switch not operating in accordance with the requirements (4.5.3 (a)) | 1 |
| Oil leaking continuously from engine posing a serious risk to road safety (8.4.1 (a) (ii)) | 1 |
| Nearside Position lamp not working (4.2.1 (a) (ii)) | 1 |
| Oil leaking excessively from engine (8.4.1 (a) (i)) | 1 |
| Exhaust system insecure (6.1.2 (a)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced Sill (7.1.1 (a) (i)) | 1 |
| Offside Rear Shock absorbers has an excessively worn bush (5.3.2 (c)) | 1 |