| Most common failures | No# failures |
|---|
| Headlamp aim out of alignment | 44 |
| Brake pipe excessively corroded | 21 |
| Registration plate lamp issues | 16 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 16 |
| Brakes imbalanced across an axle | 15 |
| Offside Side repeater not working |1.4.A.2c| | 13 |
| Offside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 13 |
| Windscreen wiper does not clear the windscreen effectively | 12 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 12 |
| Nearside Side repeater not working |1.4.A.2c| | 12 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 11 |
| Offside Headlamp insecure |1.7.3| | 11 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 10 |
| Service brake: efficiency below requirements |3.7.B.7| | 10 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 9 |
| Offside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 9 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 8 |
| Offside Rear fog lamp not working |1.3.2b| | 8 |
| Nearside Headlamp insecure |1.7.3| | 8 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 7 |
| Nearside Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
| Nearside Front Track rod end ball joint has excessive play |2.2.B.1f| | 6 |
| Rear Exhaust system not adequately supported |7.1.1| | 6 |
| Nearside Front position lamp|s| not working |1.1.A.3b| | 6 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 6 |
| Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 6 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 6 |
| Nearside Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 6 |
| Offside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 5 |
| Nearside Rear wheel bearing rough when rotated |2.6.1| | 5 |
| Horn not working |1.6.2a| | 5 |
| Battery insecure |1.9.1| | 5 |
| Exhaust emits an excessive level of metered smoke for a non-turbo charged engine |7.4.B.3b| | 5 |
| Brake hose excessively deteriorated | 5 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 5 |
| Offside Front Side repeater not working |1.4.A.2c| | 5 |
| Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 5 |
| Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 4 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 4 |
| Windscreen washer not working | 4 |
| Offside Stop lamp not working |1.2.1b| | 4 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Nearside Front Side repeater not working |1.4.A.2c| | 4 |
| Emissions not tested |7.0| | 4 |
| Nearside front brake binding |3.7.B.1| | 4 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 4 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 4 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 4 |
| Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 4 |
| Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 4 |
| Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 4 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 3 |
| Nearside Front Headlamp insecure |1.7.3| | 3 |
| Front brake application uneven | 3 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 3 |
| Offside Front Position lamp not working (4.2.1 (a) (ii)) | 3 |
| Brake pedal has insufficient reserve movement |3.3.A.5| | 3 |
| Parking brake lever has no reserve travel |3.1.6b| | 3 |
| Rear parking brake recording little or no effort | 3 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Fuel system component leaking |7.2.3| | 3 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 3 |
| Rear brake binding | 3 |
| Offside Headlamp not working on main beam |1.7.5a| | 3 |
| Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 3 |
| Brake load sensing valve linkage seized |3.6.E.3| | 3 |
| Nearside Front front brake binding |3.7.B.1| | 3 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 2 |
| Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 2 |
| Offside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
| Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Horn not working (7.7 (a) (ii)) | 2 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 2 |
| Nearside Side repeater not working (4.4.1 (a) (ii)) | 2 |
| Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 2 |
| Nearside Rear wheel bearing has excessive play |2.6.2| | 2 |
| Horn not working (7.7 (a)) | 2 |
| Rear Brake load sensing valve seized |3.6.E.3| | 2 |
| Offside Front Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
| Nearside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 2 |
| Offside Headlamp excessively damaged so that the light output is severely reduced |1.7.5a| | 2 |
| Offside Rear wheel bearing rough when rotated |2.6.1| | 2 |
| Offside Direction indicator not working |1.4.A.2c| | 2 |
| Brake pedal spongy |3.3.B.1b| | 2 |
| Offside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 2 |
| Parking brake: efficiency below requirements |3.7.B.7| | 2 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Offside Headlamp aim projected beam image is obviously incorrect (4.1.2 (c)) | 2 |
| Headlamp insecure |1.7.3| | 2 |
| Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
| Offside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
| Offside Front Headlamp insecure |1.7.3| | 2 |
| Brake pedal fouling on other parts of the vehicle |3.3.A.4| | 2 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 2 |
| Offside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 2 |
| Nearside Front Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 2 |
| Offside Front Shock absorber has a serious fluid leak |2.7.3| | 2 |
| Exhaust tailpipe not capable of allowing the emission probe to be inserted |7.4.B.1| | 2 |
| Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 2 |
| Nearside Stop lamp not working |1.2.1b| | 2 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
| Offside Rear Stop lamp not working |1.2.1b| | 2 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded outer sill |5.2.6| | 2 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded outer sill |2.4.A.3| | 2 |
| Nearside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 2 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 2 |
| Offside Rear Shock absorber has negligible damping effect |2.7.5| | 2 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 2 |
| Offside Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
| Offside Front Direction indicator not working |1.4.A.2c| | 2 |
| Front Windscreen wiper blade deteriorated |8.2.2| | 2 |
| Offside Front front brake binding |3.7.B.1| | 2 |
| Rear Exhaust mounting missing |7.1.1b| | 2 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Rear position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 2 |
| Front brake disc in such a condition that it is seriously weakened | 2 |
| Front passenger door hinge insecure |6.2.B.2| | 2 |
| Offside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
| Exhaust has part of the system excessively deteriorated |7.1.1a| | 2 |
| Rear Brake valve leaking |3.6.A.1| | 2 |
| Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 2 |
| Offside Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
| Headlamp insecure Both |1.7.3| | 1 |
| Offside Rear fog lamp emits a light other than red |1.3.2e| | 1 |
| Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc Both outer |2.5.C.1a| | 1 |
| Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Front All direction indicators not working (4.4.1 (a) (ii)) | 1 |
| Offside Front Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected Wheel arch (5.3.6 (a) (ii)) | 1 |
| Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Subframe mounting prescribed area excessively corroded significantly reducing structural strength Nearside and offside front (5.3.6 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength Floor (5.3.6 (a) (i)) | 1 |
| Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength Inner sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength Chassis (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced Sill to floor (7.1.1 (a) (i)) | 1 |
| Offside Front All position lamps not working |1.1.A.3b| | 1 |
| Nearside Rear Stop lamp not working |1.2.1b| | 1 |
| Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 1 |
| Direction indicator flashing more than 120 times a minute |1.4.A.2g| | 1 |
| Nearside Front Upper Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Fuel pipe leaking |7.2.3| | 1 |
| Exhaust emits clearly visible black smoke during acceleration |7.4.A2| | 1 |
| Electrical wiring insecure Engine bay |1.9.2a| | 1 |
| Nearside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Offside Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Electrical wiring insecure and connectors likely to become disconnected fuel pump solenoid (4.11 (a) (ii)) | 1 |
| Fuel pipe leaking (6.1.3 (b) (i)) | 1 |
| Brake load sensing valve linkage defective and function impaired (1.1.17 (a)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced (7.1.1 (a) (i)) | 1 |
| Nearside Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Offside Suspension component mounting prescribed area damaged to the extent that control of the vehicle is likely to be adversely affected (5.3.6 (a) (ii)) | 1 |
| Nearside Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 1 |
| Offside Vehicle structure has excessive corrosion which adversely affects braking or steering (6.1.1 (c) (ii)) | 1 |
| Service brake lagging in operation (1.2.1 (d)) | 1 |
| Nearside Front Direction indicator missing |1.4.A.2b| | 1 |
| Offside Front Direction indicator missing |1.4.A.2b| | 1 |
| Passengers seat insecure (6.2.6 (a) (ii)) | 1 |
| Drivers seat insecure (6.2.5 (a) (ii)) | 1 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Offside Rear Direction indicator incorrect colour (4.4.3 (a)) | 1 |
| Offside Rear Position lamp showing white light to the rear (4.2.3 (a) (ii)) | 1 |
| Offside Rear reflector missing (4.8.2 (a) (ii)) | 1 |
| Rear fog lamp does not emit a steady red light (4.5.4 (a)) | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired inner wheel arch (5.3.6 (a) (i)) | 1 |
| Brake pedal anti-slip provision missing (1.1.2 (c)) | 1 |
| Nearside Obligatory mirror does not provide a view to the rear (3.3 (c)) | 1 |
| Offside Rear Outer Suspension component mounting prescribed area is excessively corroded sill rusted |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is excessively corroded bulkhead |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded chassis |2.4.A.3| | 1 |
| Nearside Front Inner Suspension component mounting prescribed area is excessively corroded wheel arch |2.4.A.3| | 1 |
| Offside Front Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
| Nearside Front Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc inner |2.5.C.1a| | 1 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside Inner Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded chassis |2.4.A.3| | 1 |
| Offside Front Subframe mounting prescribed area is excessively corroded inner arch |2.4.A.3| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded floor |2.4.A.3| | 1 |
| Nearside Front Subframe mounting prescribed area is excessively corroded chassis outrigger |2.4.A.3| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded sill |5.2.6| | 1 |
| Offside Front Brake actuating linkage mounting prescribed area is excessively corroded footwell |3.3.A.2| | 1 |
| Nearside Front Brake master cylinder/servo mounting prescribed area is excessively corroded bulkhead behind dash |3.6.C.3| | 1 |
| Nearside Front Brake master cylinder/servo mounting prescribed area is excessively corroded bulkhead |3.6.C.3| | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Front Hydraulic brake cylinder leaking hydraulic fluid |3.6.A.1| | 1 |
| Offside Rear Vehicle structure excessively corroded within 30cm of towbar mounting |6.6.6| | 1 |
| Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Nearside Seat belt anchorage prescribed area is fractured |5.2.6| | 1 |
| Nearside Front Seat belt anchorage prescribed area is fractured |5.2.6| | 1 |
| Nearside Rear Suspension component mounting prescribed area is fractured |2.4.A.3| | 1 |
| Offside Rear Suspension component mounting prescribed area is fractured |2.4.A.3| | 1 |
| Nearside Rear Axle has inadequate clearance with the chassis |2.4.A.1a| | 1 |
| Nearside Rear Sub-frame has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Front Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill area |6.1.B.2| | 1 |
| Nearside Front Integral body structure is fractured and structural rigidity is significantly reduced door outer sill |6.1.1 |a| |i|| | 1 |
| Offside Front Integral body structure is fractured and structural rigidity is significantly reduced outer sill |6.1.1 |a| |i|| | 1 |
| Offside Outer Integral body structure is fractured and structural rigidity is significantly reduced sill |6.1.1 |a| |i|| | 1 |
| Nearside Front Inner Integral body structure is fractured and structural rigidity is significantly reduced wheel arch |6.1.1 |a| |i|| | 1 |
| Offside Front Inner Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting wheel arch |6.2.2 |d| |i|| | 1 |
| Nearside Front Direction indicator not working side repeater |4.4.1 |a| |ii|| | 1 |
| Hazard warning switch inoperative |4.4.2 |a| |ii|| | 1 |
| Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
| Front Windscreen wiper not operating automatically when switched on |8.2.1b| | 1 |
| Horn not working |7.7 |a| |ii|| | 1 |
| Offside Front All direction indicators incorrect colour |4.4.3 |a|| | 1 |
| Hazard warning switch inoperative all lights not working |4.4.2 |a| |ii|| | 1 |
| Nearside Side repeater not working |4.4.1 |a| |ii|| | 1 |
| Nearside Front Brake master cylinder/servo mounting prescribed area is excessively corroded and functionality of the braking system is affected bulkhead |1.1.21 |e| |ii|| | 1 |
| Offside Front Brake prescribed area is excessively corroded and functionality of the braking system is affected bulkhead around brake pedal mounting |1.1.21 |e| |ii|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill |5.3.6 |a| |i|| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch |5.3.6 |a| |i|| | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing |5.3.6 |a| |i|| | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing |5.3.6 |a| |i|| | 1 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Outer Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Hazard warning lamps inoperative |1.4.B.1b| | 1 |
| Offside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Front Anti-roll bar has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Front Position lamp not working |4.2.1 |a|| | 1 |
| Nearside Rear Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Rear Brake pipe leaking |3.6.A.1| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner /outer sills (5.3.6 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength x2 (5.3.6 (a) (i)) | 1 |
| Nearside Front Shock absorbers has a serious fluid leak | 1 |
| Nearside Front Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Windscreen wiper blade insecure | 1 |
| Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Rear Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Front Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside front brake binding |3.7.B.1| | 1 |
| Offside Front Steering system fouling |2.2.D.2a| | 1 |
| Offside Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
| Offside Front Suspension arm pin or bush excessively worn (5.3.4 (a) (i)) | 1 |
| Nearside Front Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Offside Front Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Brake pedal anti-slip provision missing |3.3.A.1b| | 1 |
| Offside Rear Parking brake inoperative on one side |1.4.1 |a|| | 1 |
| Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
| Front Fuel system component leaking |7.2.3| | 1 |
| Nearside Rear Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Steering rack insecure |2.2.B.1a| | 1 |
| Offside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Steering system has excessive free play detected at the steering wheel |steering rack fitted| |2.2.A.1b| | 1 |
| Front Fuel hose leaking |7.2.3| | 1 |
| Nearside Front Shock absorber has negligible damping effect |2.7.5| | 1 |
| Offside Front Shock absorber has negligible damping effect |2.7.5| | 1 |
| Offside Rear Radius arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Front Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 1 |
| Offside Front Front suspension has excessive play in a upper suspension ball joint |2.5.B.1a| | 1 |
| Brake actuating linkage mounting prescribed area is excessively corroded |3.3.A.2| | 1 |
| Rear brake application uneven | 1 |
| Nearside Front Direction indicators not working |1.4.A.2c| | 1 |
| Front position lamp|s| not working both sides |1.1.A.3b| | 1 |
| Offside Front Sub-frame corroded and seriously weakened |2.4.G.1| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
| Offside Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected floor |5.3.6 |a| |ii|| | 1 |
| Offside Outer Suspension component mounting prescribed area is corroded to the extent that control of the vehicle is likely to be adversely affected sill |5.3.6 |a| |ii|| | 1 |
| Offside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Exhaust system not adequately supported |7.1.1| | 1 |
| Nearside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill holed |6.1.B.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings sill holed |6.1.B.2| | 1 |
| Nearside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Offside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced outer sill corroded (7.1.1 (a) (i)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg split (6.1.1 (c) (i)) | 1 |
| Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 1 |
| Nearside Front Suspension arm ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Nearside Front Electrical wiring damaged and bare wires exposed |1.9.2c| | 1 |
| Nearside Front Headlamp insecure (4.1.1 (c)) | 1 |
| Offside Front Headlamp insecure (4.1.1 (c)) | 1 |
| Nearside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Offside Front Headlamp light intensity severely reduced (4.1.4 (a)) | 1 |
| Nearside Front Steering component mounting prescribed area is fractured inner wheel arch (2.1.2 (e) (i)) | 1 |
| Offside Front Steering component mounting prescribed area is fractured inner wheel arch (2.1.2 (e) (i)) | 1 |
| Offside Rear Subframe mounting prescribed area excessively corroded significantly reducing structural strength rear axle mount (5.3.6 (a) (i)) | 1 |
| Front Brake prescribed area is excessively damaged bulkhead holed (1.1.21 (e) (i)) | 1 |
| Nearside Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed (7.1.1 (a) (i)) | 1 |
| Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill holed (7.1.1 (a) (i)) | 1 |
| Offside Front Headlamp not working on main beam |1.7.5a| | 1 |
| Nearside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 1 |
| Nearside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Offside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded floor |5.2.6| | 1 |
| Lower engine mounting deteriorated resulting in excessive movement |6.1.D.1a| | 1 |
| Offside Outer Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Front Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Offside Rear Lower Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Lower Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Exhaust mounting missing |7.1.1b| | 1 |
| Offside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Direction indicator flashing less than 60 times a minute |1.4.A.2g| | 1 |
| Offside Stop lamp adversely affected by the operation of another lamp |1.2.1f| | 1 |
| Offside Rear fog lamp adversely affected by the operation of another lamp |1.3.2f| | 1 |
| Nearside Front Lower Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Nearside Headlamp insecure (4.1.1 (c)) | 1 |
| Offside Headlamp insecure (4.1.1 (c)) | 1 |
| Bonnet cannot be secured in the closed position (3.1 (b) (i)) | 1 |
| Nearside Rear Service brake lagging in operation (1.2.1 (d)) | 1 |
| Nearside Outer Rear Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Bonnet cannot be secured in the closed position |3.1 |b| |i|| | 1 |
| Brake performance not tested |1.2.1 |g|| | 1 |
| Nearside Front Front position lamp|s| not in good working order |function impaired| |1.1.4a| | 1 |
| Offside Front Front position lamp|s| not in good working order |function impaired| |1.1.4a| | 1 |
| Rear Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Rear Rear fog lamp not working |1.3.2b| | 1 |
| Hazard warning tell tale not working correctly |1.4.B.1e| | 1 |
| Nearside Headlamp aim not tested |1.8.A.1c| | 1 |
| Nearside Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Braking system leaking |3.6.A.1| | 1 |
| Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Stop lamp adversely affected by the operation of another lamp indicator |1.2.1f| | 1 |
| Front Electrical wiring insecure alternator wiring |1.9.2a| | 1 |
| Electrical wiring insecure Battery terminal |1.9.2a| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded Bulk head |2.4.A.3| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded bulkhead |2.4.A.3| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded floor pan |2.4.A.3| | 1 |
| Offside Front Steering component mounting prescribed area is excessively corroded bulkhead |2.2.C.1h| | 1 |
| Offside Front Brake actuating linkage mounting prescribed area is excessively corroded bulkhead |3.3.A.2| | 1 |
| Offside Front Seat belt anchorage prescribed area is excessively corroded floor pan |5.2.6| | 1 |
| Nearside Front Seat belt anchorage prescribed area is excessively corroded floor pan |5.2.6| | 1 |
| Offside Front Inner Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Offside Front Outer Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Front Electrical wiring inadequately supported catching drive shaft |1.9.2a| | 1 |
| Nearside Front Torque/reaction arm has a deteriorated rubber bush resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Torque/reaction arm has a deteriorated rubber bush resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front Lower Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Offside Front Seat belt has a cut which has significantly weakened the webbing |5.2.2a| | 1 |
| Brake vacuum build up too slow |3.3.E.6| | 1 |
| Nearside Front suspension has excessive movement at a wishbone pin or bush |2.5.A.1c| | 1 |
| Offside Front Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Horn emits two or more alternating tones |1.6.2d| | 1 |
| Rear fog lamp not working |1.3.2b| | 1 |
| Offside Front suspension has a suspension lower ball joint securing nut loose |2.5.B.1a| | 1 |
| Nearside Front Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Front Vehicle structure is damaged, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front brake caliper has restricted free movement |3.5.1k| | 1 |
| Nearside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Front Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
| Offside Inner Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Centre Lower Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Windscreen has damage | 1 |
| Steering rack gaiter split |2.2.D.2d| | 1 |
| Offside Inner Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Front Brake master cylinder/servo mounting prescribed area is excessively corroded |3.6.C.3| | 1 |
| Offside Front Brake actuating linkage mounting prescribed area is excessively corroded |3.3.A.2| | 1 |
| Offside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Front Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Nearside Front Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| Nearside Rear Brake pipe fouled by moving parts |3.6.B.2a| | 1 |
| Nearside Rear Rear position lamp|s| not working sidelight |1.1.A.3b| | 1 |
| Exhaust emits excessive smoke or vapour of any colour |7.4.B.4| | 1 |
| Central Fuel pipe leaking underside |7.2.3| | 1 |
| Nearside Front Steering arm has relative movement at its fixings |2.2.B.1h| | 1 |
| Driver`s seat insecure |6.2.A.1| | 1 |
| Nearside Rear Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Nearside Front Front constant velocity joint is insecure |2.5.C.1b| | 1 |
| Nearside Front Suspension arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Brake servo damaged and function impaired |3.6.A.2c| | 1 |
| Driver`s door hinge insecure |6.2.B.2| | 1 |
| Front passenger door pillar deteriorated so the door cannot be readily opened or closed |6.2.B.2| | 1 |
| Nearside Front Front position lamp|s| insecure |1.1.A.3a| | 1 |
| Offside Front Front position lamp|s| insecure |1.1.A.3a| | 1 |
| Nearside Rear Rear position lamp|s| insecure |1.1.A.3a| | 1 |
| Nearside Front Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 1 |
| Offside Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Front Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Front position lamp|s| obviously incorrectly positioned |1.1.A.3a| | 1 |
| Nearside Subframe mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Rear position lamp|s| insecure |1.1.A.3a| | 1 |
| Offside Rear position lamp|s| insecure |1.1.A.3a| | 1 |
| Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 1 |
| Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Registration plate issues | 1 |
| Nearside front brake recording little or no effort |3.7.B.5a| | 1 |
| Offside Rear Radius arm has excessive play in a pin/bearing |2.4.G.2| | 1 |
| Nearside Inner Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Inner Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Brake master cylinder fluid level below minimum level |3.6.G.1e| | 1 |
| Offside Front Suspension component mounting prescribed area is inadequately repaired |2.4.A.3| | 1 |
| Nearside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Front Anti-roll bar rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear Vehicle structure has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Lower Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Offside Outer Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Centre Parking brake mechanism/associated mounting prescribed area is excessively corroded |3.1.9| | 1 |
| Offside Obligatory mirror insecure |8.1.1| | 1 |
| Offside Windscreen wiper blade deteriorated |8.2.2| | 1 |
| Inner Rear Fuel hose leaking |7.2.3| | 1 |
| Offside Front position lamp|s| not in good working order |function impaired| |1.1.4a| | 1 |
| Offside Front Suspension arm has excessive play in a ball joint |2.4.G.2| | 1 |
| Offside Lower Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
| Hazard warning switch faulty |1.4.B.1d| | 1 |
| Nearside Front brake disc excessively pitted |3.5.1h| | 1 |
| Offside Front brake disc excessively pitted |3.5.1h| | 1 |
| Nearside Outer Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Inner Rear Parking brake mechanism/associated mounting prescribed area is excessively corroded |3.1.9| | 1 |
| Steering system excessively tight |2.2.D.1| | 1 |
| Nearside Rear Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Nearside Front Front constant velocity joint gaiter insecurely mounted to its housing |2.5.C.1a| | 1 |
| Offside Front Brake pipe inadequately clipped |3.6.B.1| | 1 |
| Nearside Front Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Offside Front coil spring incomplete |2.4.C.1a| | 1 |
| Direction indicators not working |1.4.A.2c| | 1 |
| Offside Rear Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Vehicle structure has damage which adversely affects braking or steering |6.1.A.1| | 1 |
| Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 1 |
| Nearside Rear Vehicle structure has an inadequate repair which adversely affects braking or steering |6.1.A.1| | 1 |
| Offside Inner Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Rear Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 1 |