| Most common failures | No# failures |
|---|
| Windscreen wiper does not clear the windscreen effectively | 45 |
| Headlamp aim out of alignment | 23 |
| Registration plate lamp issues | 14 |
| Rear brake binding | 7 |
| Horn not working |1.6.2a| | 7 |
| Brakes imbalanced across an axle | 5 |
| Parking brake: efficiency below requirements |3.7.B.7| | 4 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 4 |
| Nearside Stop lamp not working |1.2.1b| | 3 |
| Front brake disc in such a condition that it is seriously weakened | 3 |
| Front brake application uneven | 3 |
| Brake pipe excessively corroded | 3 |
| Rear parking brake recording little or no effort | 3 |
| Offside Front wheel bearing rough when rotated |2.5.A.2| | 3 |
| Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 3 |
| Parking brake lever has excessive movement indicating incorrect adjustment (1.1.6 (c)) | 3 |
| Service brake: efficiency below requirements |3.7.B.7| | 2 |
| Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
| Nearside Windscreen wiper blade deteriorated |8.2.2| | 2 |
| Offside Stop lamp not working |1.2.1b| | 2 |
| Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Rear Rear fog lamp not working |1.3.2b| | 2 |
| Offside Front Front position lamp|s| not working |1.1.A.3b| | 2 |
| Exhaust system not adequately supported |7.1.1| | 2 |
| Rear Mechanical brake component has restricted free movement | 2 |
| Offside Upper Front position lamp|s| not working |1.1.A.3b| | 2 |
| Nearside Rear position lamp|s| not working |1.1.A.3b| | 2 |
| Nearside Rear Service brake excessively binding |1.2.1 |f|| | 2 |
| Front brake excessively fluctuating | 2 |
| Brake load sensing valve linkage seized |3.6.E.3| | 2 |
| Rear brake application uneven | 2 |
| Registration plate issues | 2 |
| Nearside Rear Stop lamp not working |1.2.1b| | 2 |
| Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 2 |
| Nearside Front Shock absorbers has a serious fluid leak | 2 |
| Brake load sensing valve seized but ABS functioning (1.1.17 (c) (i)) | 2 |
| Nearside Front Service brake excessively binding (1.2.1 (f)) | 2 |
| Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
| Brake lever has insufficient reserve travel (1.1.2 (a)) | 2 |
| Windscreen washer not working | 1 |
| Nearside Side repeater incomplete |1.5.A1b| | 1 |
| Nearside Rear Direction indicator not working |1.4.A.2c| | 1 |
| Offside Seat belt damaged sufficient to significantly weakened the webbing |5.2.2a| | 1 |
| Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Front Upper Front position lamp|s| not working |1.1.A.3b| | 1 |
| Horn not working |7.7 |a| |ii|| | 1 |
| Nearside Rear Upper All position lamps not working and lens missing |4.2.1 |a|| | 1 |
| Offside Rear Upper All position lamps not working |4.2.1 |a|| | 1 |
| Exhaust catalytic converter missing where one was fitted as standard |7.1.3| | 1 |
| Rear Axle has inadequate clearance with the bump stop |2.4.A.1a| | 1 |
| Nearside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Offside Rear Service brake excessively binding |1.2.1 |f|| | 1 |
| Central Front Brake pivot has restricted free movement |1.1.15 |e|| | 1 |
| Power steering pipe|s| or hose|s| excessively corroded |2.3.2| | 1 |
| Brake pipe leaking on a hydraulic braking system Front to rear pipe |1.1.11 |b| |ii|| | 1 |
| Brake performance not tested |1.2.1 |g|| | 1 |
| Rear Brake load sensing valve linkage seized |3.6.E.3| | 1 |
| Rear Brake load sensing valve seized |3.6.E.3| | 1 |
| Nearside Front Headlamp not working on dipped beam |1.7.5a| | 1 |
| Offside Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
| Nearside Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Front position lamp|s| not working o/s centre |1.1.A.3b| | 1 |
| Centre Stop lamp has less than 50% of the light sources illuminating |1.2.1b| | 1 |
| Offside Obligatory mirror insecure |8.1.1| | 1 |
| Brake load sensing valve seized |3.6.E.3| | 1 |
| Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
| Parking brake lever has no reserve travel |3.1.6b| | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength leaf spring front mounting bracket |5.3.6 |a| |i|| | 1 |
| Central Stop lamp not working |1.2.1b| | 1 |
| Brake load sensing valve defective and function impaired |3.6.E.3| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner wheel arch area |6.1.B.2| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings rear cross member corroded & holed n/s and o/s |6.1.B.2| | 1 |
| Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings n/s 3rd from rear cross member corroded & holed close to spring mounting |6.1.B.2| | 1 |
| Nearside Rear Suspension spring mounting prescribed area is excessively corroded and holed |2.4.A.3| | 1 |
| rear parking |secondary| brakes imbalanced | 1 |
| Nearside Front Front suspension has excessive play in a lower suspension ball joint |2.5.B.1a| | 1 |
| Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Offside Front Headlamp not working on main beam |1.7.5a| | 1 |
| Offside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
| Nearside Front wheel bearing rough when rotated |2.5.A.2| | 1 |
| Offside Rear Stop lamp not working |1.2.1b| | 1 |
| Nearside Front front brake binding |3.7.B.1| | 1 |
| An item not tested |Manual| | 1 |
| Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
| Nearside Front Upper All outline marker lamps not working |4.2.1 |a|| | 1 |
| Nearside Rear Upper All outline marker lamps not working |4.2.1 |a|| | 1 |
| Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Nearside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Front Windscreen wiper not working |3.4 |a|| | 1 |
| Horn emits two or more alternating tones |1.6.2d| | 1 |
| Nearside Rear Outline marker lamp missing |4.2.1 |a|| | 1 |
| Nearside Rear Outline marker lamp not working |4.2.1 |a|| | 1 |
| Service brake efficiency below requirements |1.2.2 |a| |i|| | 1 |
| Centre Rear Stop lamp not working |1.2.1b| | 1 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 1 |
| Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 1 |
| Parking brake: efficiency below requirements |3.7.C.1b| | 1 |
| Offside Outer Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Offside All position lamps not working |1.1.A.3b| | 1 |
| Nearside All position lamps not working |1.1.A.3b| | 1 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
| Nearside front brake binding |3.7.B.1| | 1 |
| Offside front brake binding |3.7.B.1| | 1 |
| Nearside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Offside Front Lower Front suspension has excessive play in an outer ball joint |2.5.B.2a| | 1 |
| Upper Stop lamp has less than 50% of the light sources illuminating |1.2.1b| | 1 |
| Offside Front Wheel bearing play so excessive it is likely to break up |5.1.3 |a| |ii|| | 1 |
| Nearside Front Wheel bearing has excessive play |5.1.3 |a| |i|| | 1 |
| Offside Front Shock absorbers has a serious fluid leak | 1 |
| Offside Front Inner Suspension component mounting prescribed area is excessively corroded wing |2.4.A.3| | 1 |
| Offside Front Brake pipe inadequately supported bracket detatched |3.6.B.1| | 1 |
| Rear Brake load sensing valve inoperative and ABS not fitted or inoperative |1.1.17 |c| |ii|| | 1 |
| Nearside Front Service brake excessively binding |1.2.1 |f|| | 1 |
| Offside Front Service brake excessively binding |1.2.1 |f|| | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
| Offside Rear Upper Rear position lamp|s| not working |1.1.A.3b| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner footstep |6.1.B.2| | 1 |
| Offside Front Outer Body or chassis has an unsatisfactory modification, seriously affecting its strength within 30cm of the body mountings sill at footstep |6.1.B.2| | 1 |
| Brake linkage has restricted free movement load sensing valve |3.5.1k| | 1 |
| Fuel cap/sealing device sealing washer missing |7.2.4c| | 1 |
| Rear Stop lamp not working |1.2.1b| | 1 |
| Nearside Obligatory mirror seriously deteriorated, affecting the rear view |8.1.2a| | 1 |
| Centre Stop lamp not working |1.2.1b| | 1 |
| Offside Front Direction indicator incorrect colour (1.4.A.2f) | 1 |
| Nearside Rear An item not tested (Manual) | 1 |
| Offside Front Wheel bearing has excessive play (5.1.3 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced under step (7.1.1 (a) (i)) | 1 |
| Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Exhaust emissions exceed manufacturers specified limit (8.2.2.2 (a)) | 1 |
| Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced floor to jacking point (6.1.1 (c) (i)) | 1 |
| Stop lamp(s) light intensity significantly reduced High level lamp (4.3.3 (a) (ii)) | 1 |
| Horn not working (7.7 (a) (ii)) | 1 |
| Central Rear Upper Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Nearside Front Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Front Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing corroded (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing corroded (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Seat belt anchorage prescribed area strength or continuity significantly reduced step (7.1.1 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength chassis (5.3.6 (a) (i)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheelarch (5.3.6 (a) (i)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheelarch (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking area (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking area (5.3.6 (a) (i)) | 1 |
| Offside Front Outer Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Offside Front Inner Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced sill (6.1.1 (c) (i)) | 1 |
| Rear Brake cable insecure | 1 |
| Offside Front Outer Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Sill (6.1.1 (c) (i)) | 1 |
| Brake pedal has insufficient reserve travel (1.1.2 (a)) | 1 |
| Brake fluid significantly below minimum mark (1.1.10 (d) (ii)) | 1 |
| Rear Brake cable damaged (1.1.15 (a)) | 1 |
| Rear Towbar component excessively corroded lateral member and coupling bracket. (6.1.6 (a)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
| Nearside Rear Upper Outline marker lamp showing white light to the rear (4.2.3 (a) (ii)) | 1 |
| Offside Rear Upper Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
| Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
| Nearside Front Headlamp aim not tested (4.1.2 (b)) | 1 |
| Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Rear Exhaust silencer insecure rear section (8.1.1 (b) (i)) | 1 |
| Rear Brake load sensing valve seized and ABS not fitted or inoperative (1.1.17 (c) (ii)) | 1 |
| Emissions not tested due to exhaust gas leak (8.2.2.2 (e)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength @ front mount (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength @ front mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength @ rear mount (5.3.6 (a) (i)) | 1 |
| Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength @ rear mount (5.3.6 (a) (i)) | 1 |
| Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced @ step area (7.1.1 (a) (i)) | 1 |
| Offside Front Seat belt anchorage prescribed area strength or continuity significantly reduced @ step area (7.1.1 (a) (i)) | 1 |
| Nearside Front Upper Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
| Fuel system component leaking filter (6.1.3 (b) (i)) | 1 |
| Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting Wheel arch (6.2.2 (d) (i)) | 1 |
| Subframe mounting prescribed area excessively corroded significantly reducing structural strength Front Radwell Crossmember (5.3.6 (a) (i)) | 1 |
| Horn not working (7.7 (a)) | 1 |
| Nearside Rear Upper Outline marker lamp missing (4.2.1 (a) (ii)) | 1 |
| Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wing (5.3.6 (a) (i)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer jacking point area/step area and up into wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch area where brake flexi mounts (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear of wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner jacking point area up into wheel arch (5.3.6 (a) (i)) | 1 |
| Offside Inner Seat belt anchorage prescribed area strength or continuity significantly reduced sill (7.1.1 (a) (i)) | 1 |
| Battery insecure and likely to cause a short circuit (4.13 (a) (ii)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Parking brake mechanism/associated mounting prescribed area is excessively corroded (1.1.21 (e) (i)) | 1 |
| Brake prescribed area is excessively corroded At limiter valve (1.1.21 (e) (i)) | 1 |
| Emissions unable to be completed due to exhaust blow (8.2.2.2 (e)) | 1 |
| Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wing (5.3.6 (a) (i)) | 1 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wing/arch (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
| Nearside Front Wheel bearing so rough it is likely to overheat or break up (5.1.3 (b) (ii)) | 1 |
| Side repeater not working All ns (4.4.1 (a) (ii)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner chassis leg at front (6.1.1 (c) (i)) | 1 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
| Nearside Front Wheel bearing so rough it is likely to overheat or break up (5.1.3 (b) (ii)) | 1 |
| Side repeater not working All ns (4.4.1 (a) (ii)) | 1 |
| Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Inner chassis leg at front (6.1.1 (c) (i)) | 1 |
| Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |