Most common failures | No# failures |
---|
Windscreen wiper does not clear the windscreen effectively | 41 |
Headlamp aim out of alignment | 37 |
Registration plate lamp issues | 15 |
Parking brake: efficiency below requirements |3.7.B.7| | 12 |
Rear brake binding | 11 |
Service brake: efficiency below requirements |3.7.B.7| | 7 |
Brakes imbalanced across an axle | 6 |
Exhaust has a major leak of exhaust gases |7.1.2| | 6 |
Nearside Front wheel bearing rough when rotated |2.5.A.2| | 6 |
Brake pipe excessively corroded | 5 |
Horn not working |1.6.2a| | 5 |
Brake hose excessively deteriorated | 4 |
Front brake disc in such a condition that it is seriously weakened | 4 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 4 |
Offside Front Direction indicator incorrect colour |1.4.A.2f| | 4 |
Registration plate issues | 3 |
Horn not working (7.7 (a) (ii)) | 3 |
Nearside front brake binding |3.7.B.1| | 3 |
Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 3 |
Brake load sensing valve linkage seized |3.6.E.3| | 3 |
Nearside Stop lamp not working |1.2.1b| | 3 |
Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 3 |
Rear Brake load sensing valve seized |3.6.E.3| | 2 |
Offside front brake binding |3.7.B.1| | 2 |
Parking brake: efficiency below requirements |3.7.C.1b| | 2 |
Service brake efficiency below requirements (1.2.2 (a) (i)) | 2 |
Brake hose has insufficient room to move | 2 |
Offside Front wheel bearing rough when rotated |2.5.A.2| | 2 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
Parking brake lever has no reserve travel |3.1.6b| | 2 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
Offside Rear fog lamp not working |1.3.2b| | 2 |
Anti-lock braking system warning lamp indicates an ABS fault | 2 |
Offside Front front brake binding |3.7.B.1| | 2 |
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 2 |
Nearside Rear position lamp|s| not working |1.1.A.3b| | 2 |
Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 2 |
Windscreen washer not working | 2 |
Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 2 |
Nearside Front Headlamp aim beam image kick up to the offside |1.8| | 2 |
Offside Front Headlamp aim beam image kick up to the offside |1.8| | 2 |
Mechanical brake component has restricted free movement | 1 |
Nearside Front Suspension component mounting prescribed area damaged to the extent that control of the vehicle is likely to be adversely affected |5.3.6 |a| |ii|| | 1 |
Offside Front Suspension component mounting prescribed area damaged to the extent that control of the vehicle is likely to be adversely affected |5.3.6 |a| |ii|| | 1 |
Front Battery insecure |1.9.1| | 1 |
Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Nearside Rear Stop lamp emits other than a steady red light |1.2.1e| | 1 |
Offside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Rear Brake valve leaking |3.6.A.1| | 1 |
Nearside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Offside Upper Front position lamp|s| has less than 50% of the light sources illuminating |1.1.A.3b| | 1 |
Nearside Front Inner Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Offside Front Seat belt anchorage prescribed area is excessively corroded step/ inner sill |5.2.6| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded outer chassis next to step |2.4.A.3| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded outer chassis next to step |2.4.A.3| | 1 |
Offside Front Suspension spring mounting prescribed area is excessively corroded front inner wing next to shocker/coil spring |2.4.A.3| | 1 |
Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Front Fuel system component leaking (6.1.3 (b) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner top wheel arch (5.3.6 (a) (i)) | 1 |
Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Nearside Front Shock absorbers has a serious fluid leak | 1 |
Offside Inner Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Brake pipe inadequately clipped full length |3.6.B.1| | 1 |
brake disc excessively pitted |3.5.1h| | 1 |
Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced outrigger (6.1.1 (c) (i)) | 1 |
Offside Rear Service brake excessively binding parking brake not releasing fully (1.2.1 (f)) | 1 |
Nearside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
Rear Brake load sensing valve seized and ABS not fitted or inoperative (1.1.17 (c) (ii)) | 1 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings jacking point |6.1.B.2| | 1 |
Stop lamp not working Both |1.2.1b| | 1 |
Front Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
Horn not working (7.7 (a)) | 1 |
Offside Stop lamp(s) adversely affected by the operation of another lamp (4.3.3 (b)) | 1 |
Nearside Front front brake binding |3.7.B.1| | 1 |
Brake hose damaged | 1 |
front brake binding |3.7.B.1| | 1 |
Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
Stop lamp remains on when the brakes are released | 1 |
Nearside Stop lamp|s| all not working |4.3.1 |a| |iii|| | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength |5.3.6 |a| |i|| | 1 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings strut top area |6.1.B.2| | 1 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings underside doorstep |6.1.B.2| | 1 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings inner arch |6.1.B.2| | 1 |
Nearside Subframe mounting prescribed area is excessively corroded chassis rail |2.4.A.3| | 1 |
Offside Subframe mounting prescribed area is excessively corroded chassis rail |2.4.A.3| | 1 |
Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings front cross member ,radiator mount |6.1.B.2| | 1 |
Offside Front Brake pipe inadequately supported mounting plate inner arch |3.6.B.1| | 1 |
Nearside Front Brake pipe inadequately supported mounting plate inner arch |3.6.B.1| | 1 |
Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 1 |
Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting |6.2.2 |d| |i|| | 1 |
Offside Rear Service brake lagging in operation |1.2.1 |d|| | 1 |
Parking brake efficiency less than 50% of the required value |1.4.2 |a| |ii|| | 1 |
Nearside Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
Offside Front Electrical wiring inadequately supported loom at engine bay fouling on alternator close to pulley / drive belt |1.9.2a| | 1 |
Nearside Headlamp insecure |1.7.3| | 1 |
Driver`s seat insecure |6.2.A.1| | 1 |
Offside Rear wheel bearing rough when rotated |2.6.1| | 1 |
Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point (5.3.6 (a) (i)) | 1 |
Offside Front Outer Suspension component mounting prescribed area is inadequately repaired doorstep (5.3.6 (a) (i)) | 1 |
Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Offside Rear Rear fog lamp not working |1.3.2b| | 1 |
Nearside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Nearside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
Fuel tank leaking |7.2.3| | 1 |
Fuel pipe leaking |7.2.3| | 1 |
Nearside Rear Upper Outline marker lamp does not illuminate simultaneously with the position lamps (4.2.2 (a)) | 1 |
Offside Headlamp levelling device inoperative |4.1.5 |a|| | 1 |
Exhaust system not adequately supported |7.1.1| | 1 |
Nearside Front Outline marker lamp not working |4.2.1 |a|| | 1 |
Offside Front Outline marker lamp not working |4.2.1 |a|| | 1 |
Offside Rear Service brake excessively binding (1.2.1 (f)) | 1 |
Nearside Front Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength turret (5.3.6 (a) (i)) | 1 |
Nearside Rear Upper Rear position lamp|s| not working |1.1.A.3b| | 1 |
Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Marked in yellow paint (6.1.1 (c) (i)) | 1 |
Offside Upper Front position lamp|s| not working |1.1.A.3b| | 1 |
Parking brake efficiency below requirements |1.4.2 |a| |i|| | 1 |
Nearside Rear Brake pipe at imminent risk of failure or fracture front to rear |1.1.11 |a|| | 1 |
Nearside Lower Battery insecure under car leisure battery insure |1.9.1| | 1 |
Central Lower Electrical wiring inadequately supported above exhaust |1.9.2a| | 1 |
Rear Brake cable insecure | 1 |
Rear brake application uneven | 1 |
Rear parking brake recording little or no effort | 1 |
Windscreen wiper blade deteriorated |8.2.2| | 1 |
Brake servo vacuum pipe deteriorated |3.6.C.1b| | 1 |
Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.1 |c| |ii|| | 1 |
Offside Rear Upper Rear position lamp|s| not working |1.1.A.3b| | 1 |
Bootlid cannot be secured in the closed position |6.4.1| | 1 |
Parking brake is not capable of being maintained in operation by direct mechanical action only |3.1.2| | 1 |
Nearside Front Subframe mounting prescribed area is fractured split |2.4.A.3| | 1 |
Rear Mechanical brake component has restricted free movement | 1 |
Front Bonnet cannot be secured in the closed position |8.4.1| | 1 |
Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Nearside Rear Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
Rear Exhaust emits excessive smoke or vapour of any colour |7.4.B.4| | 1 |
Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
Nearside Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
Rear fog lamp switch faulty |1.3.1a| | 1 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 1 |
Nearside Rear Stop lamp not working |1.2.1b| | 1 |
Rear Rear fog lamp not working |1.3.2b| | 1 |
Rear fog lamp tell tale not working |1.3.1b| | 1 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Nearside Rear Upper Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Offside Rear brake disc excessively pitted |3.5.1h| | 1 |
Nearside Front Seat belt affected by an insecure seat fixing |5.2.1b| | 1 |
Nearside Headlamp aim beam image kick up to the offside |1.8| | 1 |
Offside Headlamp aim beam image kick up to the offside |1.8| | 1 |
Offside Rear fog lamp missing |1.3.2a| | 1 |
Front Windscreen wiper not working (3.4 (a)) | 1 |
All direction indicators not working (4.4.1 (a) (ii)) | 1 |
Offside Rear Upper Position lamp not working (4.2.1 (a) (ii)) | 1 |
Stop lamp(s) remains on when the brakes are released All Stop lights (4.3.2 (a) (iii)) | 1 |
Nearside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
Offside Rear Brake disc significantly and obviously worn (1.1.14 (a) (i)) | 1 |
Offside Rear Direction indicator not working (4.4.1 (a) (ii)) | 1 |
Nearside Inner Drive shaft joint constant velocity boot split or insecure, no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
Front Brake pipe inadequately clipped |3.6.B.1| | 1 |
Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 1 |
Electrical wiring inadequately supported engine bay |1.9.2a| | 1 |
Other passenger door cannot be opened from outside the vehicle |6.2.3 |a|| | 1 |
Service brake has no recorded effort at a wheel both |1.2.1 |a| |ii|| | 1 |
Service brake efficiency below requirements |1.2.2 |a| |i|| | 1 |
Front Direction indicator incorrect colour |1.4.A.2f| | 1 |
Offside Rear Stop lamp not working |1.2.1b| | 1 |
Brake cable has restricted free movement |3.5.1k| | 1 |
Nearside Front An item not tested |Manual| | 1 |
Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Offside Front Battery insecure |1.9.1| | 1 |
Nearside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
Offside Headlamp aim aimed so that it dazzles other road users |1.8.A.1a| | 1 |
Nearside Rear Position lamp adversely affected by the operation of another lamp (4.2.3 (c)) | 1 |
Nearside Rear Stop lamp(s) all not working (4.3.1 (a) (iii)) | 1 |
Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced Cross Member Mount (6.1.1 (c) (i)) | 1 |
Offside Front Upper Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Windscreen wiper blade deteriorated |8.2.2| | 1 |
Offside Windscreen wiper blade deteriorated |8.2.2| | 1 |
Offside Front Brake performance not tested Brake locked on (1.2.1 (g)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill, under vehicle (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill, under vehicle (5.3.6 (a) (i)) | 1 |
Offside Rear Service brake grabbing severely brake sticking (1.2.1 (c)) | 1 |
Brake load sensing valve linkage defective and function impaired seized (1.1.17 (a)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear of wheel under wing (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength rear of wheel under wing (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength panel at shock absorber (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength panel at shock absorber (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill holed |5.3.6 |a| |i|| | 1 |
Exhaust emissions exceed manufacturer`s specified limit |8.2.2.2 |a|| | 1 |
Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
Nearside Front All direction indicators incorrect colour (4.4.3 (a)) | 1 |
Offside Front All direction indicators incorrect colour (4.4.3 (a)) | 1 |
Offside Rear All direction indicators incorrect colour (4.4.3 (a)) | 1 |
Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
Nearside Front Upper Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Rear Upper Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Rear Service brake excessively binding axle 2 (1.2.1 (f)) | 1 |
Direction indicator incorrect colour |1.4.A.2f| | 1 |
Nearside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
Offside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Rear Front position lamp|s| not working |1.1.A.3b| | 1 |
Stop lamp not working bulb incorrectly fitted |1.2.1b| | 1 |
Offside Stop lamp not working |1.2.1b| | 1 |
Exhaust emissions exceed manufacturer`s specified limit plate limit 0.9 |8.2.2.2 |a|| | 1 |
Stop lamp not working |1.2.1b| | 1 |
Nearside Headlamp lens seriously defective no pattern |4.1.1 |b| |ii|| | 1 |
Offside Headlamp lens seriously defective no pattern |4.1.1 |b| |ii|| | 1 |
Rear fog lamp not working |1.3.2b| | 1 |
Offside Front Parking brake lever has no reserve travel |3.1.6b| | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch area holed badly (6.1.1 (c) (i)) | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch holed at front panels (6.1.1 (c) (i)) | 1 |
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch area holed badly (6.1.1 (c) (i)) | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch area holed beside front chassis leg (6.1.1 (c) (i)) | 1 |
Offside Front Upper Position lamp not working marker out (4.2.1 (a) (ii)) | 1 |
Front Direction indicator incorrect colour x2 (4.4.3 (a)) | 1 |
Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings nearside front inner wheel arch by jacking |6.1.B.2| | 1 |
Nearside Front Upper Suspension spring mounting prescribed area is excessively corroded wheel arch |2.4.A.3| | 1 |