Most common failures | No# failures |
---|
Headlamp aim out of alignment | 52 |
Windscreen wiper does not clear the windscreen effectively | 44 |
Service brake: efficiency below requirements |3.7.B.7| | 31 |
Parking brake: efficiency below requirements |3.7.B.7| | 30 |
Registration plate lamp issues | 28 |
Brakes imbalanced across an axle | 18 |
Rear brake binding | 16 |
Brake pipe excessively corroded | 12 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 12 |
Service brake efficiency below requirements (1.2.2 (a) (i)) | 11 |
Exhaust has a major leak of exhaust gases |7.1.2| | 8 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 7 |
Parking brake efficiency below requirements |1.4.2 |a| |i|| | 7 |
Registration plate issues | 7 |
Brake load sensing valve linkage seized |3.6.E.3| | 6 |
Brake load sensing valve seized |3.6.E.3| | 5 |
Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 5 |
Parking brake efficiency less than 50% of the required value (1.4.2 (a) (ii)) | 5 |
Horn not working |1.6.2a| | 5 |
Nearside Stop lamp not working |1.2.1b| | 4 |
Nearside Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 4 |
Offside Front Direction indicator incorrect colour |1.4.A.2f| | 4 |
Rear parking brake recording little or no effort | 4 |
Rear fog lamp not working |1.3.2b| | 4 |
Offside Rear Direction indicator incorrect colour |1.4.A.2f| | 4 |
Offside Stop lamp not working |1.2.1b| | 4 |
Brake hose damaged | 3 |
Offside Rear Stop lamp not working |1.2.1b| | 3 |
Nearside Rear Rear position lamp|s| not working |1.1.A.3b| | 3 |
Horn not working (7.7 (a) (ii)) | 3 |
Rear brake application uneven | 3 |
Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 3 |
Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Service brake efficiency below requirements |1.2.2 |a| |i|| | 3 |
Parking brake lever has no reserve travel |3.1.6b| | 3 |
Offside Front wheel bearing rough when rotated |2.5.A.2| | 3 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 3 |
Anti-lock braking system warning lamp indicates an ABS fault | 3 |
Nearside Front front brake binding |3.7.B.1| | 3 |
Brake hose excessively deteriorated | 3 |
Front brake application uneven | 3 |
Nearside front brake binding |3.7.B.1| | 2 |
Parking brake: efficiency below requirements |3.7.C.1b| | 2 |
Offside Rear fog lamp not working |4.5.1 |a| |ii|| | 2 |
Nearside Rear Brake cable has wires broken and is significantly weakened |3.5.1b| | 2 |
Nearside Windscreen wiper blade deteriorated |8.2.2| | 2 |
Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Brake pedal has insufficient reserve travel (1.1.2 (a)) | 2 |
Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
Offside Rear Service brake excessively binding (1.2.1 (f)) | 2 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 2 |
Stop lamp(s) all not working (4.3.1 (a) (iii)) | 2 |
Offside Front Direction indicator incorrect colour (4.4.3 (a)) | 2 |
Offside Rear Direction indicator incorrect colour (4.4.3 (a)) | 2 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength jacking point area (5.3.6 (a) (i)) | 2 |
Exhaust has a major leak of exhaust gases front pipe (6.1.2 (a)) | 2 |
Emissions not tested (8.2.2.2 (e)) | 2 |
Nearside Front wheel bearing rough when rotated |2.5.A.2| | 2 |
Nearside Front Wheel bearing rough when rotated |5.1.3 |b| |i|| | 2 |
Nearside Front Inner Subframe mounting prescribed area is excessively corroded wing |2.4.A.3| | 2 |
Nearside Front Front wheel bearing rough when rotated |2.5.A.2| | 2 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
Offside Front Wheel bearing rough when rotated |5.1.3 |b| |i|| | 2 |
Nearside Front Direction indicator incorrect colour |1.4.A.2f| | 2 |
Nearside Rear Stop lamp not working |1.2.1b| | 2 |
Offside Rear Rear fog lamp not working |1.3.2b| | 2 |
Nearside Rear position lamp|s| not working |1.1.A.3b| | 2 |
Nearside Front Upper Front position lamp|s| not working |1.1.A.3b| | 2 |
Windscreen has a sticker or other obstruction encroaching into the swept area by more than 40mm outside zone `A` |8.3.1e| | 2 |
Offside Front Upper Front position lamp|s| not working |1.1.A.3b| | 2 |
Offside Rear fog lamp not working |1.3.2b| | 2 |
Offside front brake binding |3.7.B.1| | 2 |
Offside rear brake recording little or no effort |3.7.B.5a| | 2 |
Fuel system component leaking |7.2.3| | 2 |
Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
Offside Rear position lamp|s| not working |1.1.A.3b| | 2 |
Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 2 |
Offside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 2 |
Offside Front Lower Seat belt anchorage prescribed area is excessively corroded underneath inner step rotten |5.2.6| | 1 |
Nearside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
Offside Front Shock absorber has a serious fluid leak |2.7.3| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Bay panel under wing. (5.3.6 (a) (i)) | 1 |
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis leg by lower crossmember (6.1.1 (c) (i)) | 1 |
Offside Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner and outer sills (6.1.1 (c) (i)) | 1 |
Nearside Rear Additional braking device inoperative brake compensator seized (1.5 (b)) | 1 |
Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting jacking point and inner wing corroded and holed within 30cm of subframe mounting (6.2.2 (d) (i)) | 1 |
Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting jacking point corroded and holed within 30cm of subframe mounting (6.2.2 (d) (i)) | 1 |
Nearside Front Suspension spring mounting prescribed area is excessively corroded inner wing |2.4.A.3| | 1 |
Power steering pipe|s| or hose|s| excessively corroded at rack body |2.3.2| | 1 |
Nearside Front Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
rear brakes release unevenly |3.7.B.4| | 1 |
Rear Electrical wiring damaged, likely to cause a short |1.9.2b| | 1 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded inner wheel arch |2.4.A.3| | 1 |
Brake hydraulic reservoir fluid level significantly below minimum level (1.1.10 (d) (ii)) | 1 |
Brake performance not tested (1.2.1 (g)) | 1 |
Nearside Front Headlamp not working on dipped beam |4.1.1 |a| |ii|| | 1 |
Nearside Rear Position lamp likely to become detached (4.2.1 (c) (ii)) | 1 |
Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced both under inner jacking points (6.1.1 (c) (i)) | 1 |
Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
Nearside Front Upper Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
Offside Front Upper Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Front position lamp|s| incorrect colour |1.1.A.3e| | 1 |
Offside Front position lamp|s| incorrect colour |1.1.A.3e| | 1 |
Direction indicators flashing more than 120 times a minute |1.4.A.2g| | 1 |
Nearside Front Brake hose bulging under pressure |3.6.B.3| | 1 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting inner step badly corroded, outer sill (6.2.2 (d) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheel arch/strut area (5.3.6 (a) (i)) | 1 |
Brake lever has insufficient reserve travel (1.1.2 (a)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength crossmember mounting (5.3.6 (a) (i)) | 1 |
Service brake efficiency less than 50% of the required value (1.2.2 (a) (ii)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength behind wheel, chalked yellow (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength behind wheel, chalked yellow (5.3.6 (a) (i)) | 1 |
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength holed in 7 places all marked with bright paint (5.3.6 (a) (i)) | 1 |
Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength holed in two places marked with paint (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner arch holed near strut top in two places (highlighted) (5.3.6 (a) (i)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength strut top under arch holed (highlighted) (5.3.6 (a) (i)) | 1 |
Nearside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner sill and step holed underneath (6.1.1 (c) (i)) | 1 |
Offside Headlamp not working on dipped beam |1.7.5a| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded at top of inner wing |2.4.A.3| | 1 |
Nearside Front Wheel bearing so rough it is likely to overheat or break up (5.1.3 (b) (ii)) | 1 |
Offside Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
Rear Brake load sensing valve linkage seized |3.6.E.3| | 1 |
Exhaust has a major leak of exhaust gases front pipe on join to middle |7.1.2| | 1 |
Offside Rear Position lamp not working |4.2.1 |a|| | 1 |
Offside Front Service brake excessively binding |1.2.1 |f|| | 1 |
Horn sounds harsh or grating |1.6.2e| | 1 |
Nearside Front All position lamps not working |1.1.A.3b| | 1 |
Offside Front Driver`s seat insecure |6.2.A.1| | 1 |
Nearside Inner Front constant velocity joint gaiter damaged to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Nearside Outer Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Offside Lower Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Driver`s airbag missing |5.4.1| | 1 |
Offside front brake juddering severely |3.7.A.2b| | 1 |
Brake cable damaged Parking brake secondary cable excessively frayed (1.1.15 (a)) | 1 |
Exhaust system insecure Rear exhaust mounting attachment bracket broken/insecure (6.1.2 (a)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 1 |
Centre Front Exhaust has part of the system excessively deteriorated |7.1.1a| | 1 |
Nearside Rear Shock absorber has negligible damping effect |2.7.5| | 1 |
Offside Front Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
Nearside Front Suspension arm ball joint excessively worn (5.3.4 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under wing close to strut mounting (5.3.6 (a) (i)) | 1 |
Offside Front Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced under step (6.1.1 (c) (i)) | 1 |
Nearside Upper Rear position lamp|s| not working |1.1.A.3b| | 1 |
Central Stop lamp has less than 50% of the light sources illuminating |1.2.1b| | 1 |
Brake cable damaged (1.1.15 (a)) | 1 |
Nearside Rear Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 1 |
Offside Rear Suspension has inadequate clearance with the bump stop |2.4.A.1a| | 1 |
Rear Brake cable insecure | 1 |
Rear Parking brake efficiency below requirements (1.4.2 (a) (i)) | 1 |
rear parking |secondary| brake grabbing severely |3.7.B.6b| | 1 |
Offside front brakes release unevenly bind |3.7.B.4| | 1 |
Offside rear parking |secondary| brake grabbing severely |3.7.B.6b| | 1 |
Offside Rear Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheelarch (5.3.6 (a) (i)) | 1 |
Offside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength wheelarch (5.3.6 (a) (i)) | 1 |
Offside Front Outer Seat belt anchorage prescribed area strength or continuity significantly reduced sill/step (7.1.1 (a) (i)) | 1 |
Offside Front Direction indicator incorrect colour |4.4.3 |a|| | 1 |
Offside Rear Direction indicator incorrect colour |4.4.3 |a|| | 1 |
Nearside Rear Direction indicator incorrect colour |4.4.3 |a|| | 1 |
Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
Offside Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced Radiator cross member mounting area (6.1.1 (c) (i)) | 1 |
Offside Front Upper Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner arch (6.1.1 (c) (i)) | 1 |
Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength suspension turret (5.3.6 (a) (i)) | 1 |
Centre Rear Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
Centre Rear Exhaust system not adequately supported |7.1.1| | 1 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Front Upper Position lamp not working (4.2.1 (a)) | 1 |
Power steering pipe/hose leaking (2.1.5 (a)) | 1 |
Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (jacking point) (6.2.2 (d) (i)) | 1 |
Offside Front Front wheel bearing has excessive play |2.5.A.3c| | 1 |
Offside Front Front wheel bearing rough when rotated |2.5.A.2| | 1 |
Offside Front Lower Ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i)) | 1 |
Offside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength outrigger (5.3.6 (a) (i)) | 1 |
Power steering pipe|s| or hose|s| leaking from a joint Pipe from pump |2.3.3b| | 1 |
Nearside Brake cable insecure |3.5.1d| | 1 |
Offside Brake cable insecure |3.5.1d| | 1 |
Offside Rear fog lamp has less than 50% of the light sources illuminating |1.3.2b| | 1 |
Offside Front Suspension component mounting prescribed area is excessively corroded inner wheelarch |2.4.A.3| | 1 |
Offside Front Track rod end ball joint has excessive play (2.1.3 (b) (i)) | 1 |
Offside Front Lower Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Offside Front Upper Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis to inner arch by strut holed (6.1.1 (c) (i)) | 1 |
Nearside Front Upper Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced chassis to inner arch by strut fractured (6.1.1 (c) (i)) | 1 |
Nearside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point holed (6.1.1 (c) (i)) | 1 |
Offside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced jacking point holed (6.1.1 (c) (i)) | 1 |
Nearside Front Upper Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch holed (6.1.1 (c) (i)) | 1 |
Offside Front Upper Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch holed (6.1.1 (c) (i)) | 1 |
Nearside Front Lower Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced inner step holed (6.1.1 (c) (i)) | 1 |
Nearside Rear Outline marker lamp not working |4.2.1 |a|| | 1 |
Nearside Rear Upper Position lamp not working |4.2.1 |a|| | 1 |
Nearside Front Shock absorbers has a serious fluid leak | 1 |
Offside Front Shock absorbers has a serious fluid leak | 1 |
Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting (6.2.2 (d) (i)) | 1 |
Offside Front Lower Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inside step holed (6.1.1 (c) (i)) | 1 |
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inside step holed (6.1.1 (c) (i)) | 1 |
Nearside Front Upper Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced inner wheel arch holed at side if suspension spring mount. (6.1.1 (c) (i)) | 1 |
Front Lower Fuel system component leaking at fuel pump area at the front of engine. (6.1.3 (b) (i)) | 1 |
Nearside Front Wheel bearing has excessive play wheel bearing (5.1.3 (a) (i)) | 1 |
Nearside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Offside Parking brake inoperative on one side (1.4.1 (a)) | 1 |
Parking brake lever defective so that it cannot be satisfactorily operated restricted movement (1.1.6 (d)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength under battery/inner wheel arch (5.3.6 (a) (i)) | 1 |
Rear Mechanical brake component has restricted free movement | 1 |
Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
Horn not working (7.7 (a)) | 1 |
Offside Rear Stop lamp|s| not working |4.3.1 |a| |ii|| | 1 |
Front brake excessively fluctuating | 1 |
Exhaust system not adequately supported |7.1.1| | 1 |
Brake load sensing valve linkage defective and function impaired |3.6.E.3| | 1 |
Exhaust has a major leak of exhaust gases front pipe hole by hanger |7.1.2| | 1 |
Exhaust system not adequately supported tail pipe broken |7.1.1| | 1 |
Fuel pipe leaking from cap to tank |7.2.3| | 1 |
Nearside Electrical wiring inadequately supported |1.9.2a| | 1 |
Nearside rear brake grabbing severely |3.7.A.5b| | 1 |
Battery insecure |1.9.1| | 1 |
Nearside Lower Rear position lamp|s| not working |1.1.A.3b| | 1 |
Service brake: efficiency below requirements |3.7.C.1a| | 1 |
Nearside Front Prop shaft joint constant velocity boot no longer prevents the ingress of dirt |6.1.7 |g| |ii|| | 1 |
Nearside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
Nearside Front Front constant velocity joint gaiter deteriorated to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Exhaust system insecure (6.1.2 (a)) | 1 |
Suspension component mounting prescribed area is excessively corroded n/s/f shock tower area corodded |2.4.A.3| | 1 |
Exhaust emits an excessive level of metered smoke for a turbo charged engine 3.43 |7.4.B.3b| | 1 |
Drive shaft which forms part of the suspension coupling gaiter damaged to the extent that it no longer prevents the ingress of dirt etc o/s/f outer cv boot split |2.4.G.4e| | 1 |
Offside Rear Position lamp has a product on the lens or light source which shows white light to the rear Lens damaged / broken (4.2.3 (b) (ii)) | 1 |
Front Exhaust system not adequately supported |7.1.1| | 1 |
Emissions not tested |7.0| | 1 |
Nearside Front Inner Suspension component mounting prescribed area excessively corroded significantly reducing structural strength WING / ARCH STRUT MOUNT AREA (5.3.6 (a) (i)) | 1 |
Nearside Front Service brake excessively binding (1.2.1 (f)) | 1 |
Front Exhaust has a major leak of exhaust gases (6.1.2 (a)) | 1 |
Nearside Front Fuel system component leaking @ fuel filter area (6.1.3 (b) (i)) | 1 |
Offside Rear Hydraulic brake cylinder leaking hydraulic fluid back plate wet n contaminated (1.1.16 (b) (i)) | 1 |
Offside Front Seat belt anchorage prescribed area is excessively corroded inner sill |5.2.6| | 1 |
Offside Upper Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Offside Front Brake hose excessively damaged |3.6.B.4d| | 1 |
Nearside Rear position lamp|s| adversely affected by the operation of another lamp INTERACTION WITH INDICATOR |1.1.A.3f| | 1 |
Offside Outer Front constant velocity joint gaiter insecure to the extent that it no longer prevents the ingress of dirt etc |2.5.C.1a| | 1 |
Exhaust has a major leak of exhaust gases SILENCER |7.1.2| | 1 |
Offside Rear wheel bearing rough when rotated rear and mid |2.6.1| | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel Arch |5.3.6 |a| |i|| | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength Wheel Arch |5.3.6 |a| |i|| | 1 |
Nearside Rear Upper Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Upper Front position lamp|s| not working |1.1.A.3b| | 1 |
Offside Track rod end ball joint has excessive play |2.2.B.1f| | 1 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
Offside Front Side repeater not working (4.4.1 (a) (ii)) | 1 |
Nearside Front Lower Steering linkage ball joint has excessive play (2.1.3 (b) (i)) | 1 |
Offside Front Upper Macpherson strut mounting corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced step area (7.1.1 (a) (i)) | 1 |
Front Exhaust has a major leak of exhaust gases cat (6.1.2 (a)) | 1 |
Offside Front Front position lamp|s| not working |1.1.A.3b| | 1 |
Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
Offside Rear Service brake excessively binding |1.2.1 |f|| | 1 |
Offside Rear fog lamp adversely affected by the operation of another lamp |1.3.2f| | 1 |
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced cross member (6.1.1 (c) (i)) | 1 |
Nearside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced bulk head (6.1.1 (c) (i)) | 1 |
Offside Rear Rear position lamp|s| not working |1.1.A.3b| | 1 |
Offside Front Outline marker lamp not working (4.2.1 (a) (ii)) | 1 |
Nearside Side repeater not working |1.4.A.2c| | 1 |
Offside Rear Towbar component insecure |6.6.1| | 1 |
Offside Obligatory mirror seriously damaged, affecting the rear view |8.1.2a| | 1 |
Nearside Front Seat belt anchorage prescribed area strength or continuity significantly reduced |7.1.1 |a| |i|| | 1 |
Front Exhaust has a major leak of exhaust gases |6.1.2 |a|| | 1 |
Central Integral body structure corroded to the extent that the rigidity of the assembly is significantly reduced |6.1.1 |c| |i|| | 1 |
Battery insecure and likely to fall from carrier (4.13 (a) (ii)) | 1 |
Nearside Front Direction indicator incorrect colour (4.4.3 (a)) | 1 |
Offside Front Suspension component attachment bracket/mounting corroded and seriously weakened (5.3.3 (b) (i)) | 1 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 1 |
Offside Rear Brake cable has wires broken and is significantly weakened |3.5.1b| | 1 |
Offside Rear All position lamps not working |1.1.A.3b| | 1 |
Nearside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outrigger |6.2.2 |d| |i|| | 1 |
Offside Front Integral body structure or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mounting outrigger |6.2.2 |d| |i|| | 1 |
Front Service brake is causing the vehicle to swerve to the nearside |3.7.C.2| | 1 |
Offside Front Vehicle structure corroded to the extent that the rigidity of the assembly is significantly reduced (6.1.1 (c) (i)) | 1 |
Nearside Rear Direction indicator incorrect colour (4.4.3 (a)) | 1 |
Nearside Front Inner Brake disc significantly and obviously worn surface (1.1.14 (a) (i)) | 1 |
Offside Front Inner Brake disc significantly and obviously worn surface (1.1.14 (a) (i)) | 1 |
Rear Towbar component excessively corroded (6.1.6 (a)) | 1 |
Offside Front Suspension component mounting prescribed area fractured to the extent that control of the vehicle is likely to be adversely affected step and inner sill (5.3.6 (a) (ii)) | 1 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch areas. McPherson strut mount prescribed area - marked in yellow (5.3.6 (a) (i)) | 1 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch areas. McPherson strut mount prescribed area - marked in yellow (5.3.6 (a) (i)) | 1 |
Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch areas x2 - marked in yellow (5.3.6 (a) (i)) | 1 |
Nearside Front Subframe mounting prescribed area excessively corroded significantly reducing structural strength under side of jacking point - marked in yellow (5.3.6 (a) (i)) | 1 |
Nearside Front Direction indicator incorrect colour (1.4.A.2f) | 1 |
Offside Front Direction indicator incorrect colour (1.4.A.2f) | 1 |
Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 1 |
Exhaust has a major leak of exhaust gases front pipe |7.1.2| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded at rear of jacking point |2.4.A.3| | 1 |
Offside Front brake disc excessively pitted |3.5.1h| | 1 |
Offside Seat belt anchorage prescribed area strength or continuity significantly reduced sill/innersill (7.1.1 (a) (i)) | 1 |
Offside Suspension component mounting prescribed area excessively corroded significantly reducing structural strength innerwing (5.3.6 (a) (i)) | 1 |
Offside Rear Body has a sharp edge caused by damage light lens on bicycle rack |6.1.C.1| | 1 |
Nearside Front Electrical wiring insecure |1.9.2a| | 1 |
Offside Front Lower Ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.2.C.1c| | 1 |
Steering column top mounting bracket insecure |2.1.2d| | 1 |
Nearside Front Subframe mounting prescribed area is excessively corroded at jacking point |2.4.A.3| | 1 |
Offside Front Subframe mounting prescribed area is excessively corroded at jacking point |2.4.A.3| | 1 |
Nearside Rear position lamp|s| insecure |1.1.A.3a| | 1 |