Most common failures | No# failures |
---|
Headlamp aim out of alignment | 111 |
Service brake: efficiency below requirements |3.7.B.7| | 59 |
Windscreen wiper does not clear the windscreen effectively | 53 |
Registration plate issues | 45 |
Exhaust emissions carbon monoxide content after 2nd fast idle excessive |7.3.D.3| | 40 |
Brakes imbalanced across an axle | 38 |
Registration plate lamp issues | 31 |
Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 29 |
Exhaust emissions Lambda reading after 2nd fast idle outside specified limits |7.3.D.3| | 27 |
Exhaust emissions carbon monoxide content at idle excessive |7.3.D.4| | 25 |
Parking brake: efficiency below requirements |3.7.B.7| | 21 |
Rear parking brake recording little or no effort | 20 |
Rear brake binding | 19 |
Stop lamp remains on when the brakes are released | 19 |
Nearside Stop lamp not working |1.2.1b| | 18 |
Offside Rear wheel bearing has excessive play |2.6.2| | 16 |
Windscreen washer not working | 15 |
Nearside Rear wheel bearing has excessive play |2.6.2| | 14 |
Exhaust has a major leak of exhaust gases |7.1.2| | 13 |
Nearside Headlamp not working on main beam |1.7.5a| | 13 |
Nearside Headlamp not working on dipped beam |1.7.5a| | 12 |
Nearside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 12 |
Offside Stop lamp not working |1.2.1b| | 12 |
Rear Exhaust has a major leak of exhaust gases |7.1.2| | 12 |
Nearside Front Direction indicator not working |1.4.A.2c| | 11 |
Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 11 |
Nearside Front position lamp|s| not working |1.1.A.3b| | 10 |
Centre Exhaust has a major leak of exhaust gases |7.1.2| | 10 |
Exhaust emissions hydrocarbon content after 2nd fast idle excessive |7.3.D.3| | 10 |
Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 10 |
Horn not working |1.6.2a| | 10 |
Offside front brake binding |3.7.B.1| | 10 |
Nearside front brake binding |3.7.B.1| | 10 |
Nearside Front Headlamp not working on dipped beam |1.7.5a| | 8 |
Offside Front position lamp|s| not working |1.1.A.3b| | 8 |
Nearside Rear Stop lamp not working |1.2.1b| | 8 |
Parking brake lever releases when knocked |3.1.6a| | 8 |
Offside Rear Stop lamp not working |1.2.1b| | 8 |
Service brake efficiency below requirements (1.2.2 (a) (i)) | 8 |
Offside Headlamp not working on main beam |1.7.5a| | 7 |
Offside Rear fog lamp not working |1.3.2b| | 7 |
Front Exhaust has a major leak of exhaust gases |7.1.2| | 7 |
Parking brake lever ratchet mechanism is excessively worn |3.1.5| | 7 |
Nearside Headlamp aim beam image kick up to the offside |1.8| | 7 |
Offside Headlamp aim beam image kick up to the offside |1.8| | 7 |
Battery insecure |1.9.1| | 6 |
Braking system leaking |3.6.A.1| | 6 |
Service brake efficiency below requirements |1.2.2 |a| |i|| | 6 |
Direction indicators not working |1.4.A.2c| | 6 |
Offside Front Headlamp not working on main beam |1.7.5a| | 6 |
Nearside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 6 |
Offside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 5 |
Stop lamp not working |1.2.1b| | 5 |
Offside Front Position lamp not working (4.2.1 (a) (ii)) | 5 |
Nearside Front Direction indicators not working |1.4.A.2c| | 5 |
Nearside Front Position lamp not working (4.2.1 (a) (ii)) | 5 |
Offside Front front brake binding |3.7.B.1| | 5 |
Front brake application uneven | 5 |
Offside Front Front position lamp|s| not working |1.1.A.3b| | 5 |
Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 5 |
Offside Front Headlamp not working on dipped beam |1.7.5a| | 5 |
Nearside Front Headlamp aim beam image kick up to the offside |1.8| | 5 |
Offside Front Headlamp aim beam image kick up to the offside |1.8| | 5 |
Nearside Front Service brake excessively binding (1.2.1 (f)) | 4 |
Rear fog lamp tell tale not working |1.3.1b| | 4 |
Nearside Front Headlamp not working on main beam |1.7.5a| | 4 |
Exhaust carbon monoxide content after 2nd fast idle exceeds default limits |8.2.1.2 |b|| | 4 |
Brake hydraulic reservoir fluid level below minimum level |3.6.G.1b| | 4 |
Exhaust carbon monoxide content at idle exceeds default limits (8.2.1.2 (b)) | 4 |
Offside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
Offside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 4 |
Offside Rear Position lamp not working (4.2.1 (a) (ii)) | 4 |
Rear fog lamp not working |1.3.2b| | 4 |
Fuel tank leaking |7.2.3| | 4 |
Offside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 4 |
Exhaust emits dense blue smoke at idle |7.3.A.2b| | 4 |
Nearside Rear Direction indicator not working |1.4.A.2c| | 4 |
Nearside Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 4 |
Offside Rear wheel bearing rough when rotated |2.6.1| | 4 |
Hazard warning lamps not flashing in phase, with ignition off |1.4.B.1f| | 4 |
Offside Rear Rear fog lamp not working |1.3.2b| | 3 |
Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 3 |
Nearside Headlamp not working on main beam (4.1.1 (a) (ii)) | 3 |
Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 3 |
Offside Rear Service brake excessively binding (1.2.1 (f)) | 3 |
Exhaust emissions carbon monoxide content excessive (8.2.1.2 (b)) | 3 |
Offside Front Direction indicator not working |1.4.A.2c| | 3 |
Offside Headlamp not working on dipped beam |1.7.5a| | 3 |
Exhaust catalytic converter missing where one was fitted as standard |7.1.3| | 3 |
Nearside Front Front position lamp|s| not working |1.1.A.3b| | 3 |
Front brake excessively fluctuating | 3 |
Offside rear brake recording little or no effort |3.7.B.5a| | 3 |
Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 3 |
Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) | 3 |
Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) | 3 |
Nearside Front Direction indicator not working (4.4.1 (a) (ii)) | 3 |
Nearside Track rod end ball joint has excessive play |2.2.B.1f| | 3 |
Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Parking brake efficiency below requirements (1.4.2 (a) (i)) | 3 |
Front Windscreen wiper not operating automatically when switched on |8.2.1b| | 3 |
Hazard warning lamps not flashing in phase, with ignition on |1.4.B.1f| | 3 |
Rear Exhaust system not adequately supported |7.1.1| | 3 |
Offside Rear Rear wheel bearing has excessive play |2.6.2| | 3 |
Brake pipe excessively corroded | 3 |
Exhaust carbon monoxide content after 2nd fast idle exceeds manufacturers specified limits (8.2.1.2 (a)) | 3 |
Stop lamp(s) all not working (4.3.1 (a) (iii)) | 3 |
Driver`s door cannot be opened from outside the vehicle |6.2.B.1b| | 3 |
Hazard warning switch faulty |1.4.B.1d| | 3 |
Nearside Front front brake binding |3.7.B.1| | 3 |
Offside Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
Nearside Front Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
rear brake recording little or no effort |3.7.B.5a| | 3 |
Rear Shock absorber has an excessively worn bush |2.7.4| | 3 |
Offside Rear Rear wheel bearing rough when rotated |2.6.1| | 3 |
Emissions not tested |7.0| | 3 |
Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 3 |
Nearside Steering pivot point has excessive play |2.2.B.1g| | 3 |
Nearside Front Suspension spring mounting prescribed area is excessively corroded |2.4.A.3| | 3 |
Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt (5.3.4 (b) (ii)) | 2 |
Offside Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
Nearside Front Steering component mounting prescribed area is excessively corroded |2.2.C.1h| | 2 |
Offside Inner Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Front Headlamp not working on main beam |1.7.5a| | 2 |
Nearside Rear Rear position lamp|s| excessively deteriorated so that it is not visible from a reasonable distance |1.1.A.3d| | 2 |
Offside Drag link end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
Main beam `tell-tale` not working |1.7.4c| | 2 |
Nearside rear brake recording little or no effort |3.7.B.5a| | 2 |
Hazard warning lamps inoperative |1.4.B.1b| | 2 |
Brake pedal spongy |3.3.B.1b| | 2 |
Exhaust carbon monoxide content at idle exceeds manufacturers specified limits (8.2.1.2 (b)) | 2 |
Offside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
Nearside Rear Stop lamp(s) not working (4.3.1 (a) (ii)) | 2 |
Nearside Rear position lamp|s| not working |1.1.A.3b| | 2 |
Offside Headlamp insecure |1.7.3| | 2 |
Exhaust Lambda reading after 2nd fast idle outside specified limits |8.2.1.2 |c|| | 2 |
Nearside Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 2 |
Nearside Rear Position lamp not working (4.2.1 (a) (ii)) | 2 |
Rear fog lamp not working (4.5.1 (a) (ii)) | 2 |
Nearside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
Offside Front Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
Mechanical brake component has restricted free movement | 2 |
Rear brake application uneven | 2 |
Indicator tell tale inoperative |1.4.A.2a| | 2 |
Nearside Front Front position lamp|s| adversely affected by the operation of another lamp |1.1.A.3f| | 2 |
Headlamp aim not tested |1.8.A.1c| | 2 |
Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength (5.3.6 (a) (i)) | 2 |
Offside Front Anti-roll bar linkage ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Exhaust engine idle speed too high |7.3.A.2a| | 2 |
Nearside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
Offside Front Upper Suspension arm ball joint dust cover no longer prevents the ingress of dirt |5.3.4 |b| |ii|| | 2 |
Offside Rear Trailing arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
Centre Stop lamp not working |1.2.1b| | 2 |
Fuel cap/sealing device sealing washer missing |7.2.4c| | 2 |
Offside Front brake caliper has restricted free movement |3.5.1k| | 2 |
Oil leaking excessively from engine |8.4.1 |a| |i|| | 2 |
Parking brake lever has no reserve travel |3.1.6b| | 2 |
Exhaust emits excessive dense blue smoke during acceleration |7.3.A.2c| | 2 |
Offside Rear position lamp|s| not working |1.1.A.3b| | 2 |
Nearside Front Vehicle structure has excessive corrosion which adversely affects braking or steering |6.1.A.1| | 2 |
Centre Exhaust system not adequately supported |7.1.1| | 2 |
Nearside Direction indicators not working |1.4.A.2c| | 2 |
Steering system has excessive free play detected at the steering wheel |steering box fitted| |2.2.A.1a| | 2 |
Nearside Front Lower Suspension arm ball joint dust cover excessively deteriorated so that it no longer prevents the ingress of dirt |2.4.G.2| | 2 |
Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 2 |
Offside Front Upper Tie bar/rod rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 2 |
Nearside Inner Track rod end ball joint has excessive play |2.2.B.1f| | 2 |
Offside Front coil spring incomplete |2.4.C.1a| | 2 |
Nearside Rear Rear wheel bearing rough when rotated |2.6.1| | 2 |
Nearside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
Offside Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
Nearside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 2 |
Offside Headlamp aim projected beam image is obviously incorrect |4.1.2 |c|| | 2 |
Windscreen wiper blade insecure | 2 |
Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 2 |
Nearside Track rod end ball joint dust cover excessively damaged so that it no longer prevents the ingress of dirt |2.2.C.1c| | 2 |
Nearside Front Anti-roll bar attachment bracket/mounting corroded and its strength is seriously reduced |2.4.G.1| | 2 |
Nearside Rear Coil spring not correctly located |2.4.C.2| | 2 |
Offside Front Headlamp aim beam image obviously incorrect |1.8.A.1b| | 2 |
Offside Front Lower Suspension arm has excessive play in a ball joint |2.4.G.2| | 2 |
Rear Exhaust has part of the system excessively deteriorated |7.1.1a| | 2 |
Nearside Windscreen wiper blade deteriorated |8.2.2| | 2 |
Nearside Rear Direction indicator incorrect colour |1.4.A.2f| | 2 |
Brake master cylinder leaking |1.1.10 |b| |ii|| | 2 |
Nearside Front Steering arm has relative movement at its fixings |2.2.B.1h| | 2 |