| Most common failures | No# failures |
|---|
| Exhaust emissions carbon monoxide content excessive |7.3.B.1a| | 12 |
| Headlamp aim out of alignment | 11 |
| Horn not working |1.6.2a| | 10 |
| Nearside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 10 |
| Offside Rear Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 10 |
| Exhaust emissions hydrocarbon content excessive |7.3.B.1b| | 9 |
| Offside Rear fog lamp not working |1.3.2b| | 7 |
| Brake pipe excessively corroded | 6 |
| Offside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 5 |
| Registration plate lamp issues | 5 |
| Service brake: efficiency below requirements |3.7.B.7| | 5 |
| Rear fog lamp tell tale not working |1.3.1b| | 5 |
| Windscreen wiper does not clear the windscreen effectively | 5 |
| Brakes imbalanced across an axle | 4 |
| Nearside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 4 |
| Offside Stop lamp not working |1.2.1b| | 4 |
| Offside Headlamp not working on dipped beam |1.7.5a| | 3 |
| Offside Headlamp not working on main beam |1.7.5a| | 3 |
| Offside rear brake recording little or no effort |3.7.B.5a| | 3 |
| Nearside Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Offside Rear Seat belt anchorage prescribed area is excessively corroded |5.2.6| | 3 |
| Offside Front position lamp|s| not working |1.1.A.3b| | 2 |
| Registration plate issues | 2 |
| Direction indicators not working |1.4.A.2c| | 2 |
| Nearside Headlamp not working on dipped beam |1.7.5a| | 2 |
| Nearside Headlamp not working on main beam |1.7.5a| | 2 |
| Nearside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 2 |
| Offside front brake binding |3.7.B.1| | 2 |
| Nearside rear brake recording little or no effort |3.7.B.5a| | 2 |
| Rear Exhaust has a major leak of exhaust gases |7.1.2| | 2 |
| Offside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Nearside Rear Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 2 |
| Offside Rear Rear fog lamp not working |1.3.2b| | 2 |
| Offside Side repeater insecure |1.4.A.2b| | 2 |
| Nearside Steering rack gaiter split |2.2.D.2d| | 2 |
| Offside Steering rack gaiter split |2.2.D.2d| | 2 |
| Windscreen has damage | 2 |
| Brake hose excessively deteriorated | 2 |
| Nearside Stop lamp not working |1.2.1b| | 2 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner sill (5.3.6 (a) (i)) | 2 |
| Exhaust emissions hydrocarbon content excessive (8.2.1.2 (b)) | 2 |
| Offside Front Service brake excessively binding (1.2.1 (f)) | 1 |
| Offside Side repeater not working (4.4.1 (a) (ii)) | 1 |
| Dipswitch does not operate immediately when selected on dipped beam (4.1.3 (b)) | 1 |
| Nearside Front Wheel bolt|s| loose |4.2.A.1e| | 1 |
| Fuel hose leaking |7.2.3| | 1 |
| Nearside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Rear Service brake application uneven across the axle |3.7.D.2b| | 1 |
| Offside Rear Brake pipe inadequately supported |3.6.B.1| | 1 |
| Hazard warning lamps inoperative |1.4.B.1b| | 1 |
| Nearside Rear Upper Tie bar/rod inappropriately repaired fitted wrong rubbing wheel. |2.4.A.2| | 1 |
| Offside Front wheel bearing has excessive play |2.5.A.3c| | 1 |
| Nearside Suspension has inadequate clearance with the bump stop suspension tide down. |2.4.A.1a| | 1 |
| Nearside Front Suspension has inadequate clearance with the bump stop tide down. |2.4.A.1a| | 1 |
| Nearside Headlamp excessively deteriorated so that the light output is severely reduced |1.7.5a| | 1 |
| Offside Front position lamp|s| not in good working order |function impaired| |1.1.4a| | 1 |
| Exhaust engine idle speed too high |7.3.A.2a| | 1 |
| Nearside Front position lamp|s| not in good working order |function impaired| |1.1.4a| | 1 |
| Offside Rear position lamp|s| excessively damaged so that it is not visible from a reasonable distance |1.1.A.3d| | 1 |
| Fuel cap/sealing device does not fasten securely by positive means |7.2.4b| | 1 |
| Nearside Rear Trailing arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Rear Trailing arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Nearside Rear wheel bearing rough when rotated |2.6.1| | 1 |
| Offside Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Rear parking brake recording little or no effort | 1 |
| Parking brake: efficiency below requirements |3.7.B.7| | 1 |
| Nearside Rear Inner Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings to outer sill |6.1.B.2| | 1 |
| Centre Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Nearside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Battery insecure |1.9.1| | 1 |
| Nearside Front Exhaust has a major leak of exhaust gases |7.1.2| | 1 |
| Offside Front Front constant velocity joint gaiter split |2.5.C.1a| | 1 |
| Nearside Stop lamp(s) not working (4.3.1 (a) (ii)) | 1 |
| Rear Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Horn not working (7.7 (a)) | 1 |
| Offside Front Outer Prop shaft joint constant velocity boot no longer prevents the ingress of dirt Clip missing (6.1.7 (g) (ii)) | 1 |
| Offside Rear Shock absorbers has a serious fluid leak | 1 |
| Offside Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Rear fog lamp switch inoperative (4.5.3 (a) (ii)) | 1 |
| Windscreen washer not working | 1 |
| Front passenger door cannot be opened from inside the vehicle |6.2.B.1b| | 1 |
| Front passenger door cannot be opened from outside the vehicle |6.2.B.1b| | 1 |
| Hazard warning switch faulty |1.4.B.1d| | 1 |
| Nearside front brake binding |3.7.B.1| | 1 |
| Nearside Rear Suspension arm has excessive play in a pin/bush front arm both bushes |2.4.G.2| | 1 |
| Offside Rear Suspension arm has excessive play in a pin/bush front arm both bushes |2.4.G.2| | 1 |
| Rear fog lamp not working |4.5.1 |a| |ii|| | 1 |
| Nearside Front Direction indicator light intensity significantly reduced bulb not correctly positioned |4.4.3 |a|| | 1 |
| Nearside Rear Radius arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Offside Front Radius arm has excessive play in a pin/bush |2.4.G.2| | 1 |
| Rear Direction indicator adversely affected by the operation of another lamp |1.4.A.2h| | 1 |
| Nearside Rear Brake hose excessively damaged |3.6.B.4d| | 1 |
| Offside Rear Coil spring mounting corroded and seriously weakened |2.4.C.3c| | 1 |
| Offside Front Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Fuel system component insecure |7.2.1| | 1 |
| Exhaust system not adequately supported |7.1.1| | 1 |
| Front Suspension arm corroded and seriously weakened |2.4.G.1| | 1 |
| Offside Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Offside Front Body or chassis has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Stop lamp not working |1.2.1b| | 1 |
| Offside Rear Direction indicator excessively damaged so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Offside Headlamp not in good working order adversely affecting beam image |1.2.4a| | 1 |
| Offside Front Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Nearside Suspension component mounting prescribed area is excessively corroded |2.4.A.3| | 1 |
| Nearside Rear Service brake has no recorded effort at a wheel (1.2.1 (a) (ii)) | 1 |
| Service brake efficiency below requirements (1.2.2 (a) (i)) | 1 |
| Nearside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Offside Rear Service brake effort inadequate at a wheel (1.2.1 (a) (i)) | 1 |
| Offside Rear fog lamp not working (4.5.1 (a) (ii)) | 1 |
| Nearside Rear Statutory seat belt missing |5.1.1| | 1 |
| Offside Rear Statutory seat belt missing |5.1.1| | 1 |
| Nearside Rear Trailing arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Trailing arm rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear Vehicle structure has excessive corrosion, seriously affecting its strength within 30cm of the body mountings |6.1.B.2| | 1 |
| Rear Seat belt locking mechanism does not secure or release |5.2.5a| | 1 |
| Nearside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Offside Rear Shock absorber has a serious fluid leak |2.7.3| | 1 |
| Offside Front coil spring incomplete |2.4.C.1a| | 1 |
| Fuel pipe leaking |7.2.3| | 1 |
| Offside Headlamp insecure (4.1.1 (c)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength outer sill (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (front section) (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength section of floor at rear upper suspension arm, rear mounting (5.3.6 (a) (i)) | 1 |
| Offside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (rear section) (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (front section) (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength section of floor, at rear upper suspension arm, rear mounting (5.3.6 (a) (i)) | 1 |
| Nearside Rear Suspension component mounting prescribed area excessively corroded significantly reducing structural strength inner wheel arch (rear section) (5.3.6 (a) (i)) | 1 |
| Nearside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Offside Rear Wheel bearing rough when rotated (5.1.3 (b) (i)) | 1 |
| Nearside Rear Direction indicator excessively deteriorated so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Offside Rear Direction indicator excessively deteriorated so that it is not visible from a reasonable distance |1.4.A.2e| | 1 |
| Towbar component insecure |6.6.1| | 1 |
| Nearside Front Suspension arm fractured |2.4.G.1| | 1 |
| Offside Front Headlamp not working on dipped beam (4.1.1 (a) (ii)) | 1 |
| Offside Front Direction indicator adversely affected by the operation of another lamp (4.4.3 (b)) | 1 |
| Offside Front Headlamp not working on main beam (4.1.1 (a) (ii)) | 1 |
| Nearside Rear Direction indicator not working |1.4.A.2c| | 1 |
| Tie bar/rod rubber bush deteriorated resulting in excessive movement |2.4.G.2| | 1 |
| Offside Rear rear brake recording little or no effort |3.7.B.5a| | 1 |
| Nearside Rear Body has a sharp edge caused by corrosion |6.1.C.1| | 1 |
| Nearside Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Offside Headlamp aim beam image kick up to the offside |1.8| | 1 |
| Fuel cap/sealing device does not fasten securely maintaining the sealing arrangement |7.2.4b| | 1 |