Most common failures | No# failures |
---|
Rear Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 5 |
Drive chain excessively loose |6.2.1d| | 3 |
Headlamp aim out of alignment | 3 |
Front position lamp does not illuminate immediately when switched on |1.1.3a| | 2 |
Front wheel bearings have excessive free play |2.3.5b| | 2 |
Drive chain worn to excess |6.2.1e| | 2 |
Throttle operating incorrectly |6.2.1f| | 2 |
Front Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 1 |
Steering control handlebar movement restricted by taut cables |2.1.2c| | 1 |
Nearside Rear Direction indicator not working |1.5.1c| | 1 |
Offside Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Front Brake disc|s| friction surface contaminated by oil or grease |3.2.A1k| | 1 |
Front suspension has inadequate damping effect. |2.3.6c| | 1 |
Roller brake test The less effective brake control does not achieve an efficiency of 25%. |3.3.A2b| | 1 |
Exhaust is leaking and excessively noisey By mounting point of lower silencer |7.1.1b| | 1 |
Front Brake fluid reservoir leaking hydraulic fluid |3.2.B1e| | 1 |
Front Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 1 |
Front Roller brake test indicates a severely grabbing brake |3.3.A1b| | 1 |
Offside Front Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Rear position lamp incorrect colour |1.1.2b| | 1 |
Front Floor brake test indicates a binding brake |3.3.C2c| | 1 |
Wheel alignment incorrect which adversely affects the steering |2.5.1| | 1 |
Offside Front Brake master cylinder leaking hydraulic fluid |3.2.B1e| | 1 |
Centre Rear Stop lamp does not illuminate immediately a brake applies |1.3.1a| | 1 |
Front Stop lamp remains on when the brake is released |1.3.1e| | 1 |
Front Roller brake test indicates a binding brake |3.3.A1a| | 1 |
Nearside Front Direction indicator flashing less than 60 times a minute |1.5.1c| | 1 |
Roller brake test indicates a binding brake |3.3.A1a| | 1 |
Headlamp at least one does not illuminate on dipped beam |1.2.2a|i|| | 1 |
Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 1 |
Locking device|s| not correctly fitted which may make the motor bicycle dangerous to ride |6.2.1h| | 1 |
Horn not working |1.7.3a| | 1 |
Registration plate issues | 1 |
Rear Rear shock absorber has inadequate damping effect. |2.4.A.3b| | 1 |
Front Brake cylinder leaking hydraulic fluid |3.2.B1e| | 1 |
Rear Roller brake test indicates a sticking brake |3.3.A1a| | 1 |
Rear Rear position lamp does not illuminate immediately when it is switched on |1.1.3a| | 1 |
Rear Brake locking device missing |3.2.A1e| | 1 |
Nearside Front shock absorber seal failed and leaking oil |2.3.3| | 1 |
Offside Rear Direction indicator incorrect colour |1.5.1b| | 1 |
Front Direction indicator incorrect colour |1.5.1b| | 1 |
Front Brake lever insecure (1.1.2 (e) (i)) | 1 |
Offside Handlebar retaining device missing Clamp bolt missing and holes don???t line up (2.2.1 (b) (i)) | 1 |
Rear Brake pedal is bent and the brake cannot be readily applied (1.1.2 (d)) | 1 |
Nearside Front Footrest missing Rubber missing (6.2.12 (a)) | 1 |
Rear Position lamp not working (4.2.1 (a)) | 1 |
Registration plate lamp issues | 1 |